aboutsummaryrefslogtreecommitdiff
path: root/board/palmtreo680/palmtreo680.c
blob: f4f6e1f5b9578e773b9f7eaaa8c16c0b3f1e756f (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
/*
 * Palm Treo 680 Support
 *
 * Copyright (C) 2013 Mike Dunn <mikedunn@newsguy.com>
 *
 * This file is released under the terms of GPL v2 and any later version.
 * See the file COPYING in the root directory of the source tree for details.
 *
 */

#include <common.h>
#include <command.h>
#include <serial.h>
#include <nand.h>
#include <malloc.h>
#include <asm/arch/pxa-regs.h>
#include <asm/arch-pxa/pxa.h>
#include <asm/arch-pxa/regs-mmc.h>
#include <asm/io.h>
#include <asm/global_data.h>
#include <u-boot/crc.h>
#include <linux/mtd/docg4.h>

DECLARE_GLOBAL_DATA_PTR;

static struct nand_chip docg4_nand_chip;

int board_init(void)
{
	/* We have RAM, disable cache */
	dcache_disable();
	icache_disable();

	gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
	gd->bd->bi_boot_params = CONFIG_SYS_DRAM_BASE + 0x100;

	return 0;
}

int dram_init(void)
{
	/* IPL initializes SDRAM (we're already running from it) */
	gd->ram_size = PHYS_SDRAM_1_SIZE;
	return 0;
}

#ifdef CONFIG_LCD
void lcd_enable(void)
{
	/*
	 * Undo the L_BIAS / gpio77 pin configuration performed by the pxa lcd
	 * driver code.  We need it as an output gpio.
	 */
	writel((readl(GAFR2_L) & ~(0xc << 24)), GAFR2_L);

	/* power-up and enable the lcd */
	writel(0x00400000, GPSR(86)); /* enable; drive high */
	writel(0x00002000, GPSR(77)); /* power; drive high */
	writel(0x02000000, GPCR(25)); /* enable_n; drive low */

	/* turn on LCD backlight and configure PWM for reasonable brightness */
	writel(0x00, PWM_CTRL0);
	writel(0x1b1, PWM_PERVAL0);
	writel(0xfd, PWM_PWDUTY0);
	writel(0x00000040, GPSR(38)); /*  backlight power on */
}
#endif

#ifdef CONFIG_MMC
int board_mmc_init(bd_t *bis)
{
	writel(1 << 10, GPSR(42)); /* power on */
	return pxa_mmc_register(0);
}
#endif

void board_nand_init(void)
{
	/* we have one 128M diskonchip G4  */

	struct mtd_info *mtd = &nand_info[0];
	struct nand_chip *nand = &docg4_nand_chip;
	if (docg4_nand_init(mtd, nand, 0))
		hang();
}

#ifdef CONFIG_SPL_BUILD
void nand_boot(void)
{
	__attribute__((noreturn)) void (*uboot)(void);

	extern const void *_start, *_end;   /* boundaries of spl in memory */

	/* size of spl; ipl loads this, and then a portion of u-boot */
	const size_t spl_image_size = ((size_t)&_end - (size_t)&_start);

	/* the flash offset of the blocks that are loaded by the spl */
	const uint32_t spl_load_offset = CONFIG_SYS_NAND_U_BOOT_OFFS +
		DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_SIZE;

	/* total number of bytes loaded by IPL */
	const size_t ipl_load_size =
		DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_CAPACITY_SPL;

	/* number of bytes of u-boot proper that was loaded by the IPL */
	const size_t ipl_uboot_load_size = ipl_load_size - spl_image_size;

	/* number of remaining bytes of u-boot that the SPL must load */
	const size_t spl_load_size =
		CONFIG_SYS_NAND_U_BOOT_SIZE - ipl_load_size;

	/* memory address where we resume loading u-boot */
	void *const load_addr =
		(void *)(CONFIG_SYS_NAND_U_BOOT_DST + ipl_uboot_load_size);

	/*
	 * Copy the portion of u-boot already read from flash by the IPL to its
	 * correct load address.
	 */
	memcpy((void *)CONFIG_SYS_NAND_U_BOOT_DST, &_end, ipl_uboot_load_size);

	/*
	 * Resume loading u-boot where the IPL left off.
	 */
	nand_spl_load_image(spl_load_offset, spl_load_size, load_addr);

#ifdef CONFIG_NAND_ENV_DST
	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
			    (void *)CONFIG_NAND_ENV_DST);

#ifdef CONFIG_ENV_OFFSET_REDUND
	nand_spl_load_image(CONFIG_ENV_OFFSET_REDUND, CONFIG_ENV_SIZE,
			    (void *)CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE);
#endif
#endif
	/*
	 * Jump to U-Boot image
	 */
	uboot = (void *)CONFIG_SYS_NAND_U_BOOT_START;
	(*uboot)();
}

void board_init_f(ulong bootflag)
{
	nand_boot();
}

#endif  /* CONFIG_SPL_BUILD */