1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
|
/*
* This file is part of the MicroPython project, http://micropython.org/
*
* The MIT License (MIT)
*
* Copyright (c) 2013, 2014 Damien P. George
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
* THE SOFTWARE.
*/
#include "py/builtin.h"
const char teensy_help_text[] =
"Welcome to MicroPython!\n"
"\n"
"For online help please visit http://micropython.org/help/.\n"
"\n"
"Quick overview of commands for the board:\n"
" pyb.info() -- print some general information\n"
" pyb.gc() -- run the garbage collector\n"
" pyb.delay(n) -- wait for n milliseconds\n"
" pyb.Switch() -- create a switch object\n"
" Switch methods: (), callback(f)\n"
" pyb.LED(n) -- create an LED object for LED n (n=1,2,3,4)\n"
" LED methods: on(), off(), toggle(), intensity(<n>)\n"
" pyb.Pin(pin) -- get a pin, eg pyb.Pin('X1')\n"
" pyb.Pin(pin, m, [p]) -- get a pin and configure it for IO mode m, pull mode p\n"
" Pin methods: init(..), value([v]), high(), low()\n"
" pyb.ExtInt(pin, m, p, callback) -- create an external interrupt object\n"
" pyb.ADC(pin) -- make an analog object from a pin\n"
" ADC methods: read(), read_timed(buf, freq)\n"
" pyb.DAC(port) -- make a DAC object\n"
" DAC methods: triangle(freq), write(n), write_timed(buf, freq)\n"
" pyb.RTC() -- make an RTC object; methods: datetime([val])\n"
" pyb.rng() -- get a 30-bit hardware random number\n"
" pyb.Servo(n) -- create Servo object for servo n (n=1,2,3,4)\n"
" Servo methods: calibration(..), angle([x, [t]]), speed([x, [t]])\n"
" pyb.Accel() -- create an Accelerometer object\n"
" Accelerometer methods: x(), y(), z(), tilt(), filtered_xyz()\n"
"\n"
"Pins are numbered X1-X12, X17-X22, Y1-Y12, or by their MCU name\n"
"Pin IO modes are: pyb.Pin.IN, pyb.Pin.OUT_PP, pyb.Pin.OUT_OD\n"
"Pin pull modes are: pyb.Pin.PULL_NONE, pyb.Pin.PULL_UP, pyb.Pin.PULL_DOWN\n"
"Additional serial bus objects: pyb.I2C(n), pyb.SPI(n), pyb.UART(n)\n"
"\n"
"Control commands:\n"
" CTRL-A -- on a blank line, enter raw REPL mode\n"
" CTRL-B -- on a blank line, enter normal REPL mode\n"
" CTRL-C -- interrupt a running program\n"
" CTRL-D -- on a blank line, do a soft reset of the board\n"
"\n"
"For further help on a specific object, type help(obj)\n"
;
|
