diff options
Diffstat (limited to 'ports/stm32/help.c')
| -rw-r--r-- | ports/stm32/help.c | 82 |
1 files changed, 41 insertions, 41 deletions
diff --git a/ports/stm32/help.c b/ports/stm32/help.c index f9d97b70d..fba0a6937 100644 --- a/ports/stm32/help.c +++ b/ports/stm32/help.c @@ -27,45 +27,45 @@ #include "py/builtin.h" const char stm32_help_text[] = -"Welcome to MicroPython!\n" -"\n" -"For online help please visit http://micropython.org/help/.\n" -"\n" -"Quick overview of commands for the board:\n" -" pyb.info() -- print some general information\n" -" pyb.delay(n) -- wait for n milliseconds\n" -" pyb.millis() -- get number of milliseconds since hard reset\n" -" pyb.Switch() -- create a switch object\n" -" Switch methods: (), callback(f)\n" -" pyb.LED(n) -- create an LED object for LED n (n=1,2,3,4)\n" -" LED methods: on(), off(), toggle(), intensity(<n>)\n" -" pyb.Pin(pin) -- get a pin, eg pyb.Pin('X1')\n" -" pyb.Pin(pin, m, [p]) -- get a pin and configure it for IO mode m, pull mode p\n" -" Pin methods: init(..), value([v]), high(), low()\n" -" pyb.ExtInt(pin, m, p, callback) -- create an external interrupt object\n" -" pyb.ADC(pin) -- make an analog object from a pin\n" -" ADC methods: read(), read_timed(buf, freq)\n" -" pyb.DAC(port) -- make a DAC object\n" -" DAC methods: triangle(freq), write(n), write_timed(buf, freq)\n" -" pyb.RTC() -- make an RTC object; methods: datetime([val])\n" -" pyb.rng() -- get a 30-bit hardware random number\n" -" pyb.Servo(n) -- create Servo object for servo n (n=1,2,3,4)\n" -" Servo methods: calibration(..), angle([x, [t]]), speed([x, [t]])\n" -" pyb.Accel() -- create an Accelerometer object\n" -" Accelerometer methods: x(), y(), z(), tilt(), filtered_xyz()\n" -"\n" -"Pins are numbered X1-X12, X17-X22, Y1-Y12, or by their MCU name\n" -"Pin IO modes are: pyb.Pin.IN, pyb.Pin.OUT_PP, pyb.Pin.OUT_OD\n" -"Pin pull modes are: pyb.Pin.PULL_NONE, pyb.Pin.PULL_UP, pyb.Pin.PULL_DOWN\n" -"Additional serial bus objects: pyb.I2C(n), pyb.SPI(n), pyb.UART(n)\n" -"\n" -"Control commands:\n" -" CTRL-A -- on a blank line, enter raw REPL mode\n" -" CTRL-B -- on a blank line, enter normal REPL mode\n" -" CTRL-C -- interrupt a running program\n" -" CTRL-D -- on a blank line, do a soft reset of the board\n" -" CTRL-E -- on a blank line, enter paste mode\n" -"\n" -"For further help on a specific object, type help(obj)\n" -"For a list of available modules, type help('modules')\n" + "Welcome to MicroPython!\n" + "\n" + "For online help please visit http://micropython.org/help/.\n" + "\n" + "Quick overview of commands for the board:\n" + " pyb.info() -- print some general information\n" + " pyb.delay(n) -- wait for n milliseconds\n" + " pyb.millis() -- get number of milliseconds since hard reset\n" + " pyb.Switch() -- create a switch object\n" + " Switch methods: (), callback(f)\n" + " pyb.LED(n) -- create an LED object for LED n (n=1,2,3,4)\n" + " LED methods: on(), off(), toggle(), intensity(<n>)\n" + " pyb.Pin(pin) -- get a pin, eg pyb.Pin('X1')\n" + " pyb.Pin(pin, m, [p]) -- get a pin and configure it for IO mode m, pull mode p\n" + " Pin methods: init(..), value([v]), high(), low()\n" + " pyb.ExtInt(pin, m, p, callback) -- create an external interrupt object\n" + " pyb.ADC(pin) -- make an analog object from a pin\n" + " ADC methods: read(), read_timed(buf, freq)\n" + " pyb.DAC(port) -- make a DAC object\n" + " DAC methods: triangle(freq), write(n), write_timed(buf, freq)\n" + " pyb.RTC() -- make an RTC object; methods: datetime([val])\n" + " pyb.rng() -- get a 30-bit hardware random number\n" + " pyb.Servo(n) -- create Servo object for servo n (n=1,2,3,4)\n" + " Servo methods: calibration(..), angle([x, [t]]), speed([x, [t]])\n" + " pyb.Accel() -- create an Accelerometer object\n" + " Accelerometer methods: x(), y(), z(), tilt(), filtered_xyz()\n" + "\n" + "Pins are numbered X1-X12, X17-X22, Y1-Y12, or by their MCU name\n" + "Pin IO modes are: pyb.Pin.IN, pyb.Pin.OUT_PP, pyb.Pin.OUT_OD\n" + "Pin pull modes are: pyb.Pin.PULL_NONE, pyb.Pin.PULL_UP, pyb.Pin.PULL_DOWN\n" + "Additional serial bus objects: pyb.I2C(n), pyb.SPI(n), pyb.UART(n)\n" + "\n" + "Control commands:\n" + " CTRL-A -- on a blank line, enter raw REPL mode\n" + " CTRL-B -- on a blank line, enter normal REPL mode\n" + " CTRL-C -- interrupt a running program\n" + " CTRL-D -- on a blank line, do a soft reset of the board\n" + " CTRL-E -- on a blank line, enter paste mode\n" + "\n" + "For further help on a specific object, type help(obj)\n" + "For a list of available modules, type help('modules')\n" ; |