Age | Commit message (Collapse) | Author |
|
With this patch it always reboots or freeze when
Lauterbach is connected, until that is solved this
patch will be reverted.
This reverts commit b58bbc0ca8a76f079fcb9abc68b76dc55797d4d1.
Conflicts:
arch/arm/mach-ux500/board-mop500-regulators.c
drivers/regulator/ab8500.c
Change-Id: Icb4d095ddb6a1fa479265015695140fd82e13a64
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17697
Reviewed-by: Rickard ANDERSSON <rickard.andersson@stericsson.com>
|
|
ST-Ericsson Linux next: -
ST-Ericsson ID: 327057
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: Ie527522083674cd94368e51f648a0b43c74c5bd6
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17675
Tested-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Lukasz RYMANOWSKI <lukasz.rymanowski@stericsson.com>
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
The APE OPP 50% mode requires no client to request
"prcmu_request_ape_opp_100_voltage" which means 1.1 V.
This APE OPP requirement is then removed from SDMMC
clock handling. Due to that the voltage is decreased
the SDMMC clock rate must also be decreased from
100 MHz to 50 MHz.
ST-Ericsson ID: 326602
Change-Id: Ie3fe11d6d031b0ba3d9eff0e698ece099490afe0
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17400
Reviewed-by: Sebastian RASMUSSEN <sebastian.rasmussen@stericsson.com>
Tested-by: Sebastian RASMUSSEN <sebastian.rasmussen@stericsson.com>
|
|
To be able to fully support APE OPP 50% without any impact
on the power consumtion, all the SDI controller configurations
must be limited. The SDMMC MCLK frequency is fixed to 50 MHz
and the voltage level is set to 0.95V.
- DDR support requires 100 MHz MCLK and 1.1 V, thus right now
not possible to support.
- 50 MHz is only possible if clock by-pass mode is working.
1. For eMMC-POP (sdi2) and for eMMC-PCB (sdi4) this is
verified.
2. For SD cards (sdi0) this is verified.
3. For sdi1 (WLAN/SDIO) the connected cw1200 chip only support
25MHz, which means the clock by-pass mode will not be used
anyway.
This patch will affect MMC performance in a negative way.
ST-Ericsson ID: ER326602
Change-Id: Ia1ea1d57f96e51ef4460ed86b28992b0cb61b9b2
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17399
Reviewed-by: Sebastian RASMUSSEN <sebastian.rasmussen@stericsson.com>
Tested-by: Sebastian RASMUSSEN <sebastian.rasmussen@stericsson.com>
|
|
To avoid unnecessarily disabling and re-enabling the PL180
eMMC controller during boot phase the disable timeout is
increased to 5 seconds. To avoid the same type of
re-enabling for external SD-cards its disable timeout is
changed accordingly.
Change-Id: I9e6f0c6bf7d8d9673efabc908a7367ccb5590f8f
Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17654
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
|
|
It provides the driver to access and configure the System
Trace Module (also known as XTI) hardware
ST-Ericsson ID: 283174, 276183
ST-Ericsson FOSS-OUT ID: Trivial
Signed-off-by: Pierre Peiffer <pierre.peiffer@stericsson.com>
Change-Id: Ief4f4970db7011b4b5087a568d175fcab94c2bc4
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/14699
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
Add thermal sensor driver for db8500
ST-Ericsson ID: CR267428
Change-Id: I6c1baaf0427fc4ed4f6308613d54cadede58f823
Signed-off-by: WenHai Fang <wenhai.h.fang@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17116
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
Write protecting some of the structs used by the AB8500 battery
manager.
Change-Id: I248caab3204eb914eda6bd1c3a85a46f4157bea7
Signed-off-by: Kalle Komierowski <karl.komierowski@gmail.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17447
Reviewed-by: QATOOLS
Reviewed-by: Johan PALSSON <johan.palsson@stericsson.com>
Tested-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
|
|
This patch adds functions for configuring the thermal sensor
functionality in the PRCMU FW.
ST Ericsson ID: 323515
ST Ericsson Linux next: 318371
ST Ericsson FOSS-OUT ID: Trivial
Change-Id: Icb5047ec8603b26a0da0dc9a91261caa12a17530
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17114
Reviewed-by: Wenhai FANG <wenhai.h.fang@stericsson.com>
Tested-by: Wenhai FANG <wenhai.h.fang@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
A small hysteresis has been added when going from a too high/low
temperature to less critical level
ST-Ericsson ID: -
Change-Id: I622b856dd14b9027ed8172f1e129980fd71b8f1d
Signed-off-by: Kalle Komierowski <karl.komierowski@gmail.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17344
Reviewed-by: Johan PALSSON <johan.palsson@stericsson.com>
Tested-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
ST-Ericsson ID: CR258978
Change-Id: I20c8e94908e620f0701649e1268ad6841fc75063
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17352
Reviewed-by: Julius GUSTAVSSON <julius.gustavsson@stericsson.com>
Reviewed-by: Maxime COQUELIN <maxime.coquelin-nonst@stericsson.com>
Tested-by: Maxime COQUELIN <maxime.coquelin-nonst@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
1) Increase RX FIFO threshold so that there
is a reduction in the number of interrupts
handled to complete a transaction.
2) Fill TX FIFO in the write function.
ST-Ericsson ID: ER 326383
Change-Id: Ib75946bed8fdb3f81dfa0e2ffeb29d6ba0be36bb
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17473
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
It is seen that i2c-nomadik controller randomly stops
generating the interrupts leading to a i2c timeout.
As a workaround to this problem add retries, to the on going
transfer on failure.
Since this behaviour does not get changed with a wait for
longer duration, the timeout can be reduced to a lower
value, leading to a quicker retry attempt.
ST-Ericsson ID: ER 325661
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Change-Id: Ic9db2b15ff5ce7e656cbbdfeb19270da9e32f9d1
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16972
Tested-by: Virupax SADASHIVPETIMATH <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
Added base offset to register addresses
ST-Ericsson ID: -
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: I58717d4d17f98fc9006b74c114f21eecaaf630c8
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17464
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
ST-Ericsson Linux next: -
ST-Ericsson ID: -
Change-Id: I6b97c355d66a836b9f2465c289588c4741516720
Signed-off-by: Alexandre Torgue <alexandre.torgue@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16960
Reviewed-by: Martin PERSSON <martin.persson@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Etienne CARRIERE <etienne.carriere@stericsson.com>
Reviewed-by: Emeric VIGIER <emeric.vigier@stericsson.com>
Tested-by: Emeric VIGIER <emeric.vigier@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
Adds API for resetting the modem via prcmu-fw.
Compatible with 8500B0_v2.1.0 PRCMU Fw
ST-Ericsson ID: CR258978
Change-Id: I452c169300c9258cd680333382e194fd4c5ba10b
Reviewed-by: Sebastien RAULT <sebastien.rault@stericsson.com>
Tested-by: Sebastien RAULT <sebastien.rault@stericsson.com>
Signed-off-by: Maxime COQUELIN <maxime.coquelin-nonst@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17351
Reviewed-by: Mattias NILSSON <mattias.i.nilsson@stericsson.com>
|
|
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Change-Id: Ib2a10aba1e8f5fb0ba45a8b2f810ac387056a6e5
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17514
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
|
|
Updates the Netlink value for MSR by using one from next available
un-used values.
ST-Ericsson ID: CR258978
Change-Id: I626e3f8b406542e02d8b5df97497f49f037edec3
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17393
Tested-by: Leelavathi PUTTASWAMY <leelavathi.puttaswamy@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
The AB8500 driver is inited too late. Trying to use
a fixed regulator with a GPIO pin fails as the fixed
regulator driver also inits at level subsys. This is
solved by changing the MFD device of AB8500
and the AB8500 GPIO driver to init at arch level.
Normally gpio drivers are inited at core level (even higher).
ST-Ericsson ID: ER 325855
Change-Id: Iae015211cfc00ab2704fe4532a111aa7a1e9dd50
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16910
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Joakim AXELSSON <joakim.axelsson@stericsson.com>
|
|
Remove U5500_MLOADER_HELPER Kconfig entry
ST-Ericsson ID: 258978
Signed-off-by: Maxime Coquelin <maxime.coquelin-nonst@stericsson.com>
Change-Id: I88ba890bc9f869a3e87de6512262fffa4c2300d6
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17482
Reviewed-by: Julius GUSTAVSSON <julius.gustavsson@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
This patch adds a function to ask the PRCMU FW to release the
power state requirements related to a USB wakeup.
This is necessary for having full support for the new APE OPP
implementation.
Change-Id: I7cd837c4c259e642132ff1324616be114b1889fc
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17159
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
During restoring of musb context ,musb clock is disabled
(peripheral clock).Enabling and disabling of peripheral clock correctly.
ST-EricssonID : ER 326730
Change-Id: I55b4b14bfc5e76b618d045eaad756d49f1cf6a1a
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17505
Reviewed-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
- Reimplementation of the MTU clocks to always run on 2.4 MHz (TIMCLK).
- Cleanup of the CLKOUT defines.
Change-Id: I8968516bb04ff02aad3688e9e7fbb3e4bd58a039
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16837
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Tested-by: Mattias WALLIN <mattias.wallin@stericsson.com>
|
|
Enabling the L3G4200D gyroscope device through mop500_power_defconfig
configuration.
ST Ericsson ID : ER326907
Change-Id: I154f82b5ef45823b0839ac1f817d0e30cd0930a1
Signed-off-by: Chethan Krishna N <chethan.krishna@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17503
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
ST-Ericsson Linux next: -
ST-Ericsson ID: -
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: Ie7cb9366abf26d22f59e51035233b4b6f703bfdd
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16852
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
|
|
During suspend uart.0 seem to handle it's irq incorrectly.
BT works after suspend and resume.This has been fixed by
store and restoring only the enabled uart ports
and console port register values.
ST-Ericsson Id: ER 326768
Change-Id: Id5a12e69e92f7992c250e00bb7c8d857f99eb6c9
Signed-off-by: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17484
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Martin PERSSON <martin.persson@stericsson.com>
|
|
Modem FW upload & download driver. Silent-reboot feature.
Remove mloader_helper, as db5500 should use the new mloader implementation.
ST-Ericsson ID: 258978
Change-Id: I3f9b0ff1792ac47d6ff431b60ddb929f57b961db
Signed-off-by: Ludovic Barre <ludovic.barre@stericsson.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin-nonst@stericsson.com>
Reviewed-by: Sebastien RAULT <sebastien.rault@stericsson.com>
Tested-by: Sebastien RAULT <sebastien.rault@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/11747
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
UART1 is not used.
ST-Ericsson Linux next: -
ST-Ericsson ID: ER323382
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: Iaf88a3bac053719426543526f75eac7ae54f6838
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17377
Reviewed-by: QATOOLS
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
ST Ericsson ID: 316281
Depends-On: I57ea2c2c68a7f02ece8c588a4d419d1a022db78e
Change-Id: I57ea2c2c68a7f02ece8c588a4d419d1a022db78e
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17469
Reviewed-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com>
Tested-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com>
|
|
ST-Ericsson Linux next: -
ST-Ericsson ID: -
ST-Ericsson FOSS-OUT ID: Trivial
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Change-Id: I2029d1600548fc1650d9c223ace29d57e76e18a9
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17337
Reviewed-by: Martin PERSSON <martin.persson@stericsson.com>
|
|
Basic support for vibrators in HREFP_20_V71 board which has
linear vibrator AAC ELV1411A. This will be sufficient for
haptic feedback purpose.
This patch enables the support for small (<50ms) vibration,
and not for longer vibration periods.
ST-Ericsson ID: ER322597
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Change-Id: I084a0d3a5a663f3e28076175399787e1b0876d62
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17264
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
Set VPll in HW ctrl by SysclkReq1 with HP/LP mode
Change-Id: I852ec045b895a3c4531b90f7f9343cbb6a125d6a
Signed-off-by: David Paris <david.paris-nonst@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16959
Reviewed-by: Martin PERSSON <martin.persson@stericsson.com>
Tested-by: Martin PERSSON <martin.persson@stericsson.com>
|
|
Disable bodybiasing, change Vsmpsext4, Vaux1 and Vpll configs
Change-Id: I17defafcf8813b483e80d4db1aac7ce26b868d5a
Signed-off-by: Alexandre Torgue <alexandre.torgue@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16958
Reviewed-by: Martin PERSSON <martin.persson@stericsson.com>
Tested-by: Martin PERSSON <martin.persson@stericsson.com>
|
|
The exit latency value for the sleep state ApSleep
was too low. The new value is 800 us and the old
value was 200 us.
ST-Ericsson ID: -
Change-Id: Iec5cb022f3e8f4617ad6f32ad51e7bbcc7d00b52
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17158
Reviewed-by: QATOOLS
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
Charger current is now maximized to compensate
for the system load while charging.
This will increase the amount of current that actually goes into
the battery.
Change-Id: I9e6a1c62758ede495b2f0dddd68e46131591233d
Signed-off-by: Kalle Komierowski <karl.komierowski@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16774
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
This patch removes a warning in order to reach a point where
we have zero warnings and Hudson can start to give -1 results
on any added ones.
This patch shall never reach mainline.
ST-Ericsson Linux next: Never
ST-Ericsson ID: -
ST-Ericsson FOSS-OUT ID: Trivial
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Change-Id: Ic80fb9b7280a52c1e03948de91b602d148b1a760
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17154
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
|
|
For some reason, IR was enabled although we have no IR in U8500's scope.
ST-Ericsson Linux next: -
ST-Ericsson ID: -
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: I05a508b2bd18d6ae9e6bd316e9464625941dfa33
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17094
|
|
SSP0 is not used.
ST-Ericsson Linux next: -
ST-Ericsson ID: ER323382
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: I2afacc66b78a1bda71164d08cf6829dcfae886ae
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17087
Tested-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Reviewed-by: Virupax SADASHIVPETIMATH <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
This patch enables support for 32bpp framebuffer. The color
depth is configured in menuconfig (System Type -> Display
selection -> Color depth). Color depth defaults to 16 bpp.
ST-Ericsson ID: ER323026
Linux-next: ST-Ericsson ID: ER282779
Change-Id: Ib5efd01afed81f89011afe311fe8b83ba02dcfdf
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16946
Tested-by: Dan JOHANSSON <dan.johansson@stericsson.com>
Reviewed-by: Jimmy RUBIN <jimmy.rubin@stericsson.com>
Reviewed-by: Per-Daniel OLSSON <per-daniel.olsson@stericsson.com>
Tested-by: Per-Daniel OLSSON <per-daniel.olsson@stericsson.com>
Reviewed-by: Robert FEKETE <robert.fekete@stericsson.com>
|
|
USB register context is lost when the regulators are disabled
as part of cpu idle.So saving the register context after
initialization and restoring it back when usb cable is connected.
ST-Ericsson ID: ER 325213
Change-Id: I2fdd0bf33c23844b3d42bd1856ae879e8529f087
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17068
Reviewed-by: QATOOLS
Reviewed-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
Correct uart-db8500.c author's list.
ST-Ericsson Linux next: -
ST-Ericsson ID: -
ST-Ericsson FOSS-OUT ID: Trivial
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Change-Id: I8bda958788c360b81d7049a8cea65b7381fa4fd0
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17075
Reviewed-by: Arun MURTHY <arun.murthy@stericsson.com>
Reviewed-by: QATOOLS
|
|
So that the pins are not set to alternate function when SKE is not used, for
power saving.
ST-Ericsson Linux next: -
ST-Ericsson ID: ER323382
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: I08418079ace063498ca912a55a48334ecc0606d0
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17070
Tested-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
Use the new dev_power_domain support to implement runtime pm. This also AMBA
drivers to gain runtime pm support without any further modifications in the
AMBA bus.
ST-Ericsson Linux next: -
ST-Ericsson ID: ER323382
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: Ic79287584cc08a370c52bf9289375afbefd38b18
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16998
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
Adds API for resetting the modem via prcmu-fw
ST-Ericsson ID: CR258978
Change-Id: Ia67828a284324025aba69e9ed9e56f5b8741508e
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/17018
Reviewed-by: Kumar A SANGHVI <kumar.sanghvi@stericsson.com>
Tested-by: Kumar A SANGHVI <kumar.sanghvi@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
Unblocks shrm_char clients waiting on read/select, on detecting
Modem Silent Reboot
ST-Ericsson ID: CR258978
Change-Id: I2e44bd8e0b54dce36930faa78d3308340350e3dd
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/9395
Reviewed-by: Christophe GUIBOUT <christophe.guibout@stericsson.com>
Tested-by: Christophe GUIBOUT <christophe.guibout@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/13225
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
SPI2 configured by selecting OtherAlternateC1 in GPIO mux. SPI2_SELECT must be
set in PRCMU_GPIOCR register to enable SPI2.
ST-Ericsson ID: ER276027
ST-Ericsson FOSS-OUT ID: Trivial
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Change-Id: I14c6286708483a0d7233bf0e23e98a753bbe788e
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16714
Reviewed-by: Daniel WILLERUD <daniel.willerud@stericsson.com>
Tested-by: Daniel WILLERUD <daniel.willerud@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
This reverts commit b073dbc4113c241ef63f3d6cc0007524169c1c86.
ST-Ericsson Linux next: -
ST-Ericsson ID: -
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: I6cb84f1ed0fcc4f2a4c3bece0be6e961b6d9f745
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16950
Reviewed-by: Mikael VATAU <mikael.vatau@stericsson.com>
Tested-by: Mikael VATAU <mikael.vatau@stericsson.com>
Reviewed-by: QATOOLS
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
|
|
Useful to check the status of the runtime pin muxing.
ST-Ericsson Linux next: -
ST-Ericsson ID: ER323382
ST-Ericsson FOSS-OUT ID: Trivial
Change-Id: I280126beedcbeaa8f7d7c28fddec877c06f34d5b
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16675
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
Change the reported rate of sgaclk back to 320MHz for hardware
that supports ARM OPP MAX.
ST Ericsson ID: 325049
ST Ericsson Linux next: 318371
ST Ericsson FOSS-OUT ID: Trivial
Change-Id: I77c3323e2df62d899cea19101382adcb1cf43a64
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Change-Id: I3b38e15b96d7077ae0734bd3a98a56fa88948d88
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16964
|
|
Required by Google CTS
Config was enabled in kernel commit: 38c9a5610e150c86ff3b74039883460e7e5cdf44
but seems to have disappeared since then.
Please refer to http://gerrit.lud.stericsson.com/gerrit/#change,4368
ST-Ericsson ID: 325036
Change-Id: I50cb55eca7b83d7ba60d03a114c82047c620227d
Reviewed-on: http://gerrit.lud.stericsson.com/gerrit/16940
Tested-by: Julius GUSTAVSSON <julius.gustavsson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|