From e14eb051ff73ab8692770762adf44045ba092398 Mon Sep 17 00:00:00 2001 From: Milosz Wasilewski Date: Wed, 1 Oct 2014 15:24:10 +0100 Subject: Update to aad7fb916a10f1065ad23de0c80a4a04bcba8437 from repo git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git branch master --- firmware/Makefile | 27 ++++++++++++++ firmware/fw_filesystem.sh | 62 +++++++++++++++++++++++++++++++++ firmware/fw_userhelper.sh | 89 +++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 178 insertions(+) create mode 100644 firmware/Makefile create mode 100644 firmware/fw_filesystem.sh create mode 100644 firmware/fw_userhelper.sh (limited to 'firmware') diff --git a/firmware/Makefile b/firmware/Makefile new file mode 100644 index 0000000..e23cce0 --- /dev/null +++ b/firmware/Makefile @@ -0,0 +1,27 @@ +# Makefile for firmware loading selftests + +# No binaries, but make sure arg-less "make" doesn't trigger "run_tests" +all: + +fw_filesystem: + @if /bin/sh ./fw_filesystem.sh ; then \ + echo "fw_filesystem: ok"; \ + else \ + echo "fw_filesystem: [FAIL]"; \ + exit 1; \ + fi + +fw_userhelper: + @if /bin/sh ./fw_userhelper.sh ; then \ + echo "fw_userhelper: ok"; \ + else \ + echo "fw_userhelper: [FAIL]"; \ + exit 1; \ + fi + +run_tests: all fw_filesystem fw_userhelper + +# Nothing to clean up. +clean: + +.PHONY: all clean run_tests fw_filesystem fw_userhelper diff --git a/firmware/fw_filesystem.sh b/firmware/fw_filesystem.sh new file mode 100644 index 0000000..3fc6c10 --- /dev/null +++ b/firmware/fw_filesystem.sh @@ -0,0 +1,62 @@ +#!/bin/sh +# This validates that the kernel will load firmware out of its list of +# firmware locations on disk. Since the user helper does similar work, +# we reset the custom load directory to a location the user helper doesn't +# know so we can be sure we're not accidentally testing the user helper. +set -e + +modprobe test_firmware + +DIR=/sys/devices/virtual/misc/test_firmware + +OLD_TIMEOUT=$(cat /sys/class/firmware/timeout) +OLD_FWPATH=$(cat /sys/module/firmware_class/parameters/path) + +FWPATH=$(mktemp -d) +FW="$FWPATH/test-firmware.bin" + +test_finish() +{ + echo "$OLD_TIMEOUT" >/sys/class/firmware/timeout + echo -n "$OLD_PATH" >/sys/module/firmware_class/parameters/path + rm -f "$FW" + rmdir "$FWPATH" +} + +trap "test_finish" EXIT + +# Turn down the timeout so failures don't take so long. +echo 1 >/sys/class/firmware/timeout +# Set the kernel search path. +echo -n "$FWPATH" >/sys/module/firmware_class/parameters/path + +# This is an unlikely real-world firmware content. :) +echo "ABCD0123" >"$FW" + +NAME=$(basename "$FW") + +# Request a firmware that doesn't exist, it should fail. +echo -n "nope-$NAME" >"$DIR"/trigger_request +if diff -q "$FW" /dev/test_firmware >/dev/null ; then + echo "$0: firmware was not expected to match" >&2 + exit 1 +else + echo "$0: timeout works" +fi + +# This should succeed via kernel load or will fail after 1 second after +# being handed over to the user helper, which won't find the fw either. +if ! echo -n "$NAME" >"$DIR"/trigger_request ; then + echo "$0: could not trigger request" >&2 + exit 1 +fi + +# Verify the contents are what we expect. +if ! diff -q "$FW" /dev/test_firmware >/dev/null ; then + echo "$0: firmware was not loaded" >&2 + exit 1 +else + echo "$0: filesystem loading works" +fi + +exit 0 diff --git a/firmware/fw_userhelper.sh b/firmware/fw_userhelper.sh new file mode 100644 index 0000000..6efbade --- /dev/null +++ b/firmware/fw_userhelper.sh @@ -0,0 +1,89 @@ +#!/bin/sh +# This validates that the kernel will fall back to using the user helper +# to load firmware it can't find on disk itself. We must request a firmware +# that the kernel won't find, and any installed helper (e.g. udev) also +# won't find so that we can do the load ourself manually. +set -e + +modprobe test_firmware + +DIR=/sys/devices/virtual/misc/test_firmware + +OLD_TIMEOUT=$(cat /sys/class/firmware/timeout) + +FWPATH=$(mktemp -d) +FW="$FWPATH/test-firmware.bin" + +test_finish() +{ + echo "$OLD_TIMEOUT" >/sys/class/firmware/timeout + rm -f "$FW" + rmdir "$FWPATH" +} + +load_fw() +{ + local name="$1" + local file="$2" + + # This will block until our load (below) has finished. + echo -n "$name" >"$DIR"/trigger_request & + + # Give kernel a chance to react. + local timeout=10 + while [ ! -e "$DIR"/"$name"/loading ]; do + sleep 0.1 + timeout=$(( $timeout - 1 )) + if [ "$timeout" -eq 0 ]; then + echo "$0: firmware interface never appeared" >&2 + exit 1 + fi + done + + echo 1 >"$DIR"/"$name"/loading + cat "$file" >"$DIR"/"$name"/data + echo 0 >"$DIR"/"$name"/loading + + # Wait for request to finish. + wait +} + +trap "test_finish" EXIT + +# This is an unlikely real-world firmware content. :) +echo "ABCD0123" >"$FW" +NAME=$(basename "$FW") + +# Test failure when doing nothing (timeout works). +echo 1 >/sys/class/firmware/timeout +echo -n "$NAME" >"$DIR"/trigger_request +if diff -q "$FW" /dev/test_firmware >/dev/null ; then + echo "$0: firmware was not expected to match" >&2 + exit 1 +else + echo "$0: timeout works" +fi + +# Put timeout high enough for us to do work but not so long that failures +# slow down this test too much. +echo 4 >/sys/class/firmware/timeout + +# Load this script instead of the desired firmware. +load_fw "$NAME" "$0" +if diff -q "$FW" /dev/test_firmware >/dev/null ; then + echo "$0: firmware was not expected to match" >&2 + exit 1 +else + echo "$0: firmware comparison works" +fi + +# Do a proper load, which should work correctly. +load_fw "$NAME" "$FW" +if ! diff -q "$FW" /dev/test_firmware >/dev/null ; then + echo "$0: firmware was not loaded" >&2 + exit 1 +else + echo "$0: user helper firmware loading works" +fi + +exit 0 -- cgit v1.2.3