Age | Commit message (Collapse) | Author |
|
commit 90a9b102eddf6a3f987d15f4454e26a2532c1c98 upstream.
As per PAPR we have to look for both EPOW sensor value and event
modifier to identify the type of event and take appropriate action.
In LoPAPR v1.1 section 10.2.2 includes table 136 "EPOW Action Codes":
SYSTEM_SHUTDOWN 3
The system must be shut down. An EPOW-aware OS logs the EPOW error
log information, then schedules the system to be shut down to begin
after an OS defined delay internal (default is 10 minutes.)
Then in section 10.3.2.2.8 there is table 146 "Platform Event Log
Format, Version 6, EPOW Section", which includes the "EPOW Event
Modifier":
For EPOW sensor value = 3
0x01 = Normal system shutdown with no additional delay
0x02 = Loss of utility power, system is running on UPS/Battery
0x03 = Loss of system critical functions, system should be shutdown
0x04 = Ambient temperature too high
All other values = reserved
We have a user space tool (rtas_errd) on LPAR to monitor for
EPOW_SHUTDOWN_ON_UPS. Once it gets an event it initiates shutdown
after predefined time. It also starts monitoring for any new EPOW
events. If it receives "Power restored" event before predefined time
it will cancel the shutdown. Otherwise after predefined time it will
shutdown the system.
Commit 79872e35469b ("powerpc/pseries: All events of
EPOW_SYSTEM_SHUTDOWN must initiate shutdown") changed our handling of
the "on UPS/Battery" case, to immediately shutdown the system. This
breaks existing setups that rely on the userspace tool to delay
shutdown and let the system run on the UPS.
Fixes: 79872e35469b ("powerpc/pseries: All events of EPOW_SYSTEM_SHUTDOWN must initiate shutdown")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
[mpe: Massage change log and add PAPR references]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200820061844.306460-1-hegdevasant@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bd72866b8da499e60633ff28f8a4f6e09ca78efe ]
These accessors must be used to read/write a big-endian bus. The value
returned or written is native-endian.
However, these accessors are defined using be{16,32}_to_cpu() or
cpu_to_be{16,32}() to make the endian conversion but these expect a
__be{16,32} when none is present. Keeping them would need a force cast
that would solve nothing at all.
So, do the conversion using swab{16,32}, like done in asm-generic for
similar situations.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/20200622114232.80039-1-luc.vanoostenryck@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bdee0e793cea10c516ff48bf3ebb4ef1820a116b ]
The Cache Control Register (CACR) of the ColdFire V3 has bits that
control high level caching functions, and also enable/disable the use
of the alternate stack pointer register (the EUSP bit) to provide
separate supervisor and user stack pointer registers. The code as
it is today will blindly clear the EUSP bit on cache actions like
invalidation. So it is broken for this case - and that will result
in failed booting (interrupt entry and exit processing will be
completely hosed).
This only affects ColdFire V3 parts that support the alternate stack
register (like the 5329 for example) - generally speaking new parts do,
older parts don't. It has no impact on ColdFire V3 parts with the single
stack pointer, like the 5307 for example.
Fix the cache bit defines used, so they maintain the EUSP bit when
carrying out cache actions through the CACR register.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63dee5df43a31f3844efabc58972f0a206ca4534 ]
We have powerpc specific logic in our page fault handling to decide if
an access to an unmapped address below the stack pointer should expand
the stack VMA.
The code was originally added in 2004 "ported from 2.4". The rough
logic is that the stack is allowed to grow to 1MB with no extra
checking. Over 1MB the access must be within 2048 bytes of the stack
pointer, or be from a user instruction that updates the stack pointer.
The 2048 byte allowance below the stack pointer is there to cover the
288 byte "red zone" as well as the "about 1.5kB" needed by the signal
delivery code.
Unfortunately since then the signal frame has expanded, and is now
4224 bytes on 64-bit kernels with transactional memory enabled. This
means if a process has consumed more than 1MB of stack, and its stack
pointer lies less than 4224 bytes from the next page boundary, signal
delivery will fault when trying to expand the stack and the process
will see a SEGV.
The total size of the signal frame is the size of struct rt_sigframe
(which includes the red zone) plus __SIGNAL_FRAMESIZE (128 bytes on
64-bit).
The 2048 byte allowance was correct until 2008 as the signal frame
was:
struct rt_sigframe {
struct ucontext uc; /* 0 1440 */
/* --- cacheline 11 boundary (1408 bytes) was 32 bytes ago --- */
long unsigned int _unused[2]; /* 1440 16 */
unsigned int tramp[6]; /* 1456 24 */
struct siginfo * pinfo; /* 1480 8 */
void * puc; /* 1488 8 */
struct siginfo info; /* 1496 128 */
/* --- cacheline 12 boundary (1536 bytes) was 88 bytes ago --- */
char abigap[288]; /* 1624 288 */
/* size: 1920, cachelines: 15, members: 7 */
/* padding: 8 */
};
1920 + 128 = 2048
Then in commit ce48b2100785 ("powerpc: Add VSX context save/restore,
ptrace and signal support") (Jul 2008) the signal frame expanded to
2304 bytes:
struct rt_sigframe {
struct ucontext uc; /* 0 1696 */ <--
/* --- cacheline 13 boundary (1664 bytes) was 32 bytes ago --- */
long unsigned int _unused[2]; /* 1696 16 */
unsigned int tramp[6]; /* 1712 24 */
struct siginfo * pinfo; /* 1736 8 */
void * puc; /* 1744 8 */
struct siginfo info; /* 1752 128 */
/* --- cacheline 14 boundary (1792 bytes) was 88 bytes ago --- */
char abigap[288]; /* 1880 288 */
/* size: 2176, cachelines: 17, members: 7 */
/* padding: 8 */
};
2176 + 128 = 2304
At this point we should have been exposed to the bug, though as far as
I know it was never reported. I no longer have a system old enough to
easily test on.
Then in 2010 commit 320b2b8de126 ("mm: keep a guard page below a
grow-down stack segment") caused our stack expansion code to never
trigger, as there was always a VMA found for a write up to PAGE_SIZE
below r1.
That meant the bug was hidden as we continued to expand the signal
frame in commit 2b0a576d15e0 ("powerpc: Add new transactional memory
state to the signal context") (Feb 2013):
struct rt_sigframe {
struct ucontext uc; /* 0 1696 */
/* --- cacheline 13 boundary (1664 bytes) was 32 bytes ago --- */
struct ucontext uc_transact; /* 1696 1696 */ <--
/* --- cacheline 26 boundary (3328 bytes) was 64 bytes ago --- */
long unsigned int _unused[2]; /* 3392 16 */
unsigned int tramp[6]; /* 3408 24 */
struct siginfo * pinfo; /* 3432 8 */
void * puc; /* 3440 8 */
struct siginfo info; /* 3448 128 */
/* --- cacheline 27 boundary (3456 bytes) was 120 bytes ago --- */
char abigap[288]; /* 3576 288 */
/* size: 3872, cachelines: 31, members: 8 */
/* padding: 8 */
/* last cacheline: 32 bytes */
};
3872 + 128 = 4000
And commit 573ebfa6601f ("powerpc: Increase stack redzone for 64-bit
userspace to 512 bytes") (Feb 2014):
struct rt_sigframe {
struct ucontext uc; /* 0 1696 */
/* --- cacheline 13 boundary (1664 bytes) was 32 bytes ago --- */
struct ucontext uc_transact; /* 1696 1696 */
/* --- cacheline 26 boundary (3328 bytes) was 64 bytes ago --- */
long unsigned int _unused[2]; /* 3392 16 */
unsigned int tramp[6]; /* 3408 24 */
struct siginfo * pinfo; /* 3432 8 */
void * puc; /* 3440 8 */
struct siginfo info; /* 3448 128 */
/* --- cacheline 27 boundary (3456 bytes) was 120 bytes ago --- */
char abigap[512]; /* 3576 512 */ <--
/* size: 4096, cachelines: 32, members: 8 */
/* padding: 8 */
};
4096 + 128 = 4224
Then finally in 2017, commit 1be7107fbe18 ("mm: larger stack guard
gap, between vmas") exposed us to the existing bug, because it changed
the stack VMA to be the correct/real size, meaning our stack expansion
code is now triggered.
Fix it by increasing the allowance to 4224 bytes.
Hard-coding 4224 is obviously unsafe against future expansions of the
signal frame in the same way as the existing code. We can't easily use
sizeof() because the signal frame structure is not in a header. We
will either fix that, or rip out all the custom stack expansion
checking logic entirely.
Fixes: ce48b2100785 ("powerpc: Add VSX context save/restore, ptrace and signal support")
Cc: stable@vger.kernel.org # v2.6.27+
Reported-by: Tom Lane <tgl@sss.pgh.pa.us>
Tested-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200724092528.1578671-2-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0e36b0d12501e278686634712975b785bae11641 ]
Commit a7a9dcd882a67 ("powerpc: Avoid taking a data miss on every
userspace instruction miss") has shown that limiting the read of
faulting instruction to likely cases improves performance.
This patch goes further into this direction by limiting the read
of the faulting instruction to the only cases where it is likely
needed.
On an MPC885, with the same benchmark app as in the commit referred
above, we see a reduction of about 3900 dTLB misses (approx 3%):
Before the patch:
Performance counter stats for './fault 500' (10 runs):
683033312 cpu-cycles ( +- 0.03% )
134538 dTLB-load-misses ( +- 0.03% )
46099 iTLB-load-misses ( +- 0.02% )
19681 faults ( +- 0.02% )
5.389747878 seconds time elapsed ( +- 0.06% )
With the patch:
Performance counter stats for './fault 500' (10 runs):
682112862 cpu-cycles ( +- 0.03% )
130619 dTLB-load-misses ( +- 0.03% )
46073 iTLB-load-misses ( +- 0.05% )
19681 faults ( +- 0.01% )
5.381342641 seconds time elapsed ( +- 0.07% )
The proper work of the huge stack expansion was tested with the
following app:
int main(int argc, char **argv)
{
char buf[1024 * 1025];
sprintf(buf, "Hello world !\n");
printf(buf);
exit(0);
}
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add include of pagemap.h to fix build errors]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f0c7baca180046824e07fc5f1326e83a8fd150c7 upstream.
John reported that on a RK3288 system the perf per CPU interrupts are all
affine to CPU0 and provided the analysis:
"It looks like what happens is that because the interrupts are not per-CPU
in the hardware, armpmu_request_irq() calls irq_force_affinity() while
the interrupt is deactivated and then request_irq() with IRQF_PERCPU |
IRQF_NOBALANCING.
Now when irq_startup() runs with IRQ_STARTUP_NORMAL, it calls
irq_setup_affinity() which returns early because IRQF_PERCPU and
IRQF_NOBALANCING are set, leaving the interrupt on its original CPU."
This was broken by the recent commit which blocked interrupt affinity
setting in hardware before activation of the interrupt. While this works in
general, it does not work for this particular case. As contrary to the
initial analysis not all interrupt chip drivers implement an activate
callback, the safe cure is to make the deferred interrupt affinity setting
at activation time opt-in.
Implement the necessary core logic and make the two irqchip implementations
for which this is required opt-in. In hindsight this would have been the
right thing to do, but ...
Fixes: baedb87d1b53 ("genirq/affinity: Handle affinity setting on inactive interrupts correctly")
Reported-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/87blk4tzgm.fsf@nanos.tec.linutronix.de
[fllinden@amazon.com - backported to 4.14]
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0c64a0dce51faa9c706fdf1f957d6f19878f4b81 ]
The Landisk setup code maps the CF IDE area using ioremap_prot(), and
passes the resulting virtual addresses to the pata_platform driver,
disguising them as I/O port addresses. Hence the pata_platform driver
translates them again using ioport_map().
As CONFIG_GENERIC_IOMAP=n, and CONFIG_HAS_IOPORT_MAP=y, the
SuperH-specific mapping code in arch/sh/kernel/ioport.c translates
I/O port addresses to virtual addresses by adding sh_io_port_base, which
defaults to -1, thus breaking the assumption of an identity mapping.
Fix this by setting sh_io_port_base to zero.
Fixes: 37b7a97884ba64bf ("sh: machvec IO death.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 89c140bbaeee7a55ed0360a88f294ead2b95201b upstream.
Booting with a 4GB LMB size causes us to panic:
qemu-system-ppc64: OS terminated: OS panic:
Memory block size not suitable: 0x0
Fix pseries_memory_block_size() to handle 64 bit LMBs.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200715000820.1255764-1-anton@ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cce844abf07b683cff5f0273977d5f8d0af94c7 upstream.
Now CPU#0 is not hotpluggable on MIPS, so prevent to create /sys/devices
/system/cpu/cpu0/online which confuses some user-space tools.
Cc: stable@vger.kernel.org
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c83b277ada72b585e6a3e52b067669df15bcedb upstream.
Recently random.h started including percpu.h (see commit
f227e3ec3b5c ("random32: update the net random state on interrupt and
activity")), which broke corenet64_smp_defconfig:
In file included from /linux/arch/powerpc/include/asm/paca.h:18,
from /linux/arch/powerpc/include/asm/percpu.h:13,
from /linux/include/linux/random.h:14,
from /linux/lib/uuid.c:14:
/linux/arch/powerpc/include/asm/mmu.h:139:22: error: unknown type name 'next_tlbcam_idx'
139 | DECLARE_PER_CPU(int, next_tlbcam_idx);
This is due to a circular header dependency:
asm/mmu.h includes asm/percpu.h, which includes asm/paca.h, which
includes asm/mmu.h
Which means DECLARE_PER_CPU() isn't defined when mmu.h needs it.
We can fix it by moving the include of paca.h below the include of
asm-generic/percpu.h.
This moves the include of paca.h out of the #ifdef __powerpc64__, but
that is OK because paca.h is almost entirely inside #ifdef
CONFIG_PPC64 anyway.
It also moves the include of paca.h out of the #ifdef CONFIG_SMP,
which could possibly break something, but seems to have no ill
effects.
Fixes: f227e3ec3b5c ("random32: update the net random state on interrupt and activity")
Cc: stable@vger.kernel.org # v5.8
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200804130558.292328-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d65d3769d1910379e1cfa61ebf387efc6bfb22c upstream.
Fix the following build error in configurations with
CONFIG_XTENSA_VARIANT_HAVE_PERF_EVENTS=y:
arch/xtensa/kernel/perf_event.c:420:29: error: passing argument 3 of
‘cpuhp_setup_state’ from incompatible pointer type
Cc: stable@vger.kernel.org
Fixes: 25a77b55e74c ("xtensa/perf: Convert the hotplug notifier to state machine callbacks")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ec0160891e387f4771f953b888b1fe951398e5d9 upstream.
Commit 711419e504eb ("irqdomain: Add the missing assignment of
domain->fwnode for named fwnode") unintentionally caused a dangling pointer
page fault issue on firmware nodes that were freed after IRQ domain
allocation. Commit e3beca48a45b fixed that dangling pointer issue by only
freeing the firmware node after an IRQ domain allocation failure. That fix
no longer frees the firmware node immediately, but leaves the firmware node
allocated after the domain is removed.
The firmware node must be kept around through irq_domain_remove, but should be
freed it afterwards.
Add the missing free operations after domain removal where where appropriate.
Fixes: e3beca48a45b ("irqdomain/treewide: Keep firmware node unconditionally allocated")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1595363169-7157-1-git-send-email-jonathan.derrick@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b4d5ec9b39f8b31d98f65bc5577b5d15d93795d7 upstream.
Since clang does not push pc and sp in function prologues, the current
implementation of unwind_frame does not work. By using the previous
frame's lr/fp instead of saved pc/sp we get valid unwinds on clang-built
kernels.
The bounds check on next frame pointer must be changed as well since
there are 8 less bytes between frames.
This fixes /proc/<pid>/stack.
Link: https://github.com/ClangBuiltLinux/linux/issues/912
Reported-by: Miles Chen <miles.chen@mediatek.com>
Tested-by: Miles Chen <miles.chen@mediatek.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e96ebd589debd9a6a793608c4ec7019c38785dea upstream.
This patch implements the __smp_store_release and __smp_load_acquire barriers
using ordered stores and loads. This avoids the sync instruction present in
the generic implementation.
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Dave Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 44069737ac9625a0f02f0f7f5ab96aae4cd819bc ]
Clang's integrated assembler complains "invalid reassignment of
non-absolute variable 'var_ddq_add'" while assembling
arch/x86/crypto/aes_ctrby8_avx-x86_64.S. It was because var_ddq_add was
reassigned with non-absolute values several times, which IAS did not
support. We can avoid the reassignment by replacing the uses of
var_ddq_add with its definitions accordingly to have compatilibility
with IAS.
Link: https://github.com/ClangBuiltLinux/linux/issues/1008
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Reported-by: Fangrui Song <maskray@google.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # build+boot Linux v5.7.5; clang v11.0.0-git
Signed-off-by: Jian Cai <caij2003@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ab49526b53d3172d1d8dd03a75c7d1f5bd21239 ]
syzbot found its way in 86_fsgsbase_read_task() and triggered this oops:
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
CPU: 0 PID: 6866 Comm: syz-executor262 Not tainted 5.8.0-syzkaller #0
RIP: 0010:x86_fsgsbase_read_task+0x16d/0x310 arch/x86/kernel/process_64.c:393
Call Trace:
putreg32+0x3ab/0x530 arch/x86/kernel/ptrace.c:876
genregs32_set arch/x86/kernel/ptrace.c:1026 [inline]
genregs32_set+0xa4/0x100 arch/x86/kernel/ptrace.c:1006
copy_regset_from_user include/linux/regset.h:326 [inline]
ia32_arch_ptrace arch/x86/kernel/ptrace.c:1061 [inline]
compat_arch_ptrace+0x36c/0xd90 arch/x86/kernel/ptrace.c:1198
__do_compat_sys_ptrace kernel/ptrace.c:1420 [inline]
__se_compat_sys_ptrace kernel/ptrace.c:1389 [inline]
__ia32_compat_sys_ptrace+0x220/0x2f0 kernel/ptrace.c:1389
do_syscall_32_irqs_on arch/x86/entry/common.c:84 [inline]
__do_fast_syscall_32+0x57/0x80 arch/x86/entry/common.c:126
do_fast_syscall_32+0x2f/0x70 arch/x86/entry/common.c:149
entry_SYSENTER_compat_after_hwframe+0x4d/0x5c
This can happen if ptrace() or sigreturn() pokes an LDT selector into FS
or GS for a task with no LDT and something tries to read the base before
a return to usermode notices the bad selector and fixes it.
The fix is to make sure ldt pointer is not NULL.
Fixes: 07e1d88adaae ("x86/fsgsbase/64: Fix ptrace() to read the FS/GS base accurately")
Co-developed-by: Jann Horn <jannh@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Chang S. Bae <chang.seok.bae@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Markus T Metzger <markus.t.metzger@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8b9fc10f2615b9a525fce56981e40b489528355 ]
if of_find_device_by_node() succeed, dwc3_octeon_device_init() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: 93e502b3c2d4 ("MIPS: OCTEON: Platform support for OCTEON III USB controller")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a9f675f950a07d5c1dbcbb97aabac56f5ed085e3 ]
The code in vdso_cpu_init that exposes the cpu and numa node to
userspace via SPRG_VDSO incorrctly masks the cpu to 12 bits. This means
that any kernel running on a box with more than 4096 threads (NR_CPUS
advertises a limit of of 8192 cpus) would expose userspace to two cpu
contexts running at the same time with the same cpu number.
Note: I'm not aware of any distro shipping a kernel with support for more
than 4096 threads today, nor of any system image that currently exceeds
4096 threads. Found via code browsing.
Fixes: 18ad51dd342a7eb09dbcd059d0b451b616d4dafc ("powerpc: Add VDSO version of getcpu")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Anton Blanchard <anton@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200715233704.1352257-1-anton@ozlabs.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bbe28fc3cbabbef781bcdf847615d52ce2e26e42 ]
hi3660-hikey960.dts:
Define a 'ports' node for 'adv7533: adv7533@39' and the
'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
binding.
This fills the requirements to meet the binding requirements,
remote endpoints are not defined.
hi6220-hikey.dts:
Change property name s/pd-gpio/pd-gpios, gpio properties should be
plural. This is just a cosmetic change.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
socfpga_setup_ocram_self_refresh()
[ Upstream commit 3ad7b4e8f89d6bcc9887ca701cf2745a6aedb1a0 ]
if of_find_device_by_node() succeed, socfpga_setup_ocram_self_refresh
doesn't have a corresponding put_device(). Thus add a jump target to
fix the exception handling for this function implementation.
Fixes: 44fd8c7d4005 ("ARM: socfpga: support suspend to ram")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f87a4f022c44e5b87e842a9f3e644fba87e8385f ]
if of_find_device_by_node() succeed, at91_pm_sram_init() doesn't have
a corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Fixes: d2e467905596 ("ARM: at91: pm: use the mmio-sram pool to access SRAM")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200604123301.3905837-1-yukuai3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 931fc82a6aaf4e2e4a5490addaa6a090d78c24a7 ]
When writing values to the IOP status/control register make sure those
values do not have any extraneous bits that will clear interrupt flags.
To place the SCC IOP into bypass mode would be desirable but this is not
achieved by writing IOP_DMAINACTIVE | IOP_RUN | IOP_AUTOINC | IOP_BYPASS
to the control register. Drop this ineffective register write.
Remove the flawed and unused iop_bypass() function. Make use of the
unused iop_stop() function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Cc: Joshua Thompson <funaho@jurai.org>
Link: https://lore.kernel.org/r/09bcb7359a1719a18b551ee515da3c4c3cf709e6.1590880333.git.fthain@telegraphics.com.au
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aeb445bf2194d83e12e85bf5c65baaf1f093bd8f ]
In the following sequence of calls, iop_do_send() gets called when the
"send" channel is not in the IOP_MSG_IDLE state:
iop_ism_irq()
iop_handle_send()
(msg->handler)()
iop_send_message()
iop_do_send()
Avoid this by testing the channel state before calling iop_do_send().
When sending, and iop_send_queue is empty, call iop_do_send() because
the channel is idle. If iop_send_queue is not empty, iop_do_send() will
get called later by iop_handle_send().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Cc: Joshua Thompson <funaho@jurai.org>
Link: https://lore.kernel.org/r/6d667c39e53865661fa5a48f16829d18ed8abe54.1590880333.git.fthain@telegraphics.com.au
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b072714bfc0e42c984b8fd6e069f3ca17de8137a ]
Once regulators are disabled after kernel boot, on Espresso board silent
hang observed because of LDO7 being disabled. LDO7 actually provide
power to CPU cores and non-cpu blocks circuitries. Keep this regulator
always-on to fix this hang.
Fixes: 9589f7721e16 ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1b6a1a162defe649c5599d661b58ac64bb6f31b6 ]
msm8916-pins.dtsi specifies "bias-pull-none" for most of the audio
pin configurations. This was likely copied from the qcom kernel fork
where the same property was used for these audio pins.
However, "bias-pull-none" actually does not exist at all - not in
mainline and not in downstream. I can only guess that the original
intention was to configure "no pull", i.e. bias-disable.
Change it to that instead.
Fixes: 143bb9ad85b7 ("arm64: dts: qcom: add audio pinctrls")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a445086f8af0b7b9bd8d1901d6f306bb154f70d ]
The puma gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7a7184f6cfa9279f1a1c10a1845d247d7fad54ff ]
The puma vcc5v0_host regulator node currently uses opposite active-values
for the enable pin. The gpio-declaration uses active-high while the
separate enable-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
gmac fix.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5d7f7d1d5e01c22894dee7c9c9266500478dca99 ]
The original code is a nop as i_mce.status is or'ed with part of itself,
fix it.
Fixes: a1300e505297 ("x86/ras/mce_amd_inj: Trigger deferred and thresholding errors interrupts")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Yazen Ghannam <yazen.ghannam@amd.com>
Link: https://lkml.kernel.org/r/20200611023238.3830-1-zhenzhong.duan@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 59b6359dd92d18f5dc04b14a4c926fa08ab66f7c upstream.
If CONFIG_DEBUG_LOCK_ALLOC=y, the kernel log is spammed with a few
hundred identical messages:
unwind: Unknown symbol address c0800300
unwind: Index not found c0800300
c0800300 is the return address from the last subroutine call (to
__memzero()) in __mmap_switched(). Apparently having this address in
the link register confuses the unwinder.
To fix this, reset the link register to zero before jumping to
start_kernel().
Fixes: 9520b1a1b5f7a348 ("ARM: head-common.S: speed up startup code")
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
|
|
commit aa54ea903abb02303bf55855fb51e3fcee135d70 upstream.
Fix build error for the case:
defined(CONFIG_SMP) && !defined(CONFIG_CPU_V6)
config: keystone_defconfig
CC arch/arm/kernel/signal.o
In file included from ../include/linux/random.h:14,
from ../arch/arm/kernel/signal.c:8:
../arch/arm/include/asm/percpu.h: In function ‘__my_cpu_offset’:
../arch/arm/include/asm/percpu.h:29:34: error: ‘current_stack_pointer’ undeclared (first use in this function); did you mean ‘user_stack_pointer’?
: "Q" (*(const unsigned long *)current_stack_pointer));
^~~~~~~~~~~~~~~~~~~~~
user_stack_pointer
Fixes: f227e3ec3b5c ("random32: update the net random state on interrupt and activity")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bdd65589593edd79b6a12ce86b3b7a7c6dae5208 upstream.
0day reported a possible circular locking dependency:
Chain exists of:
&irq_desc_lock_class --> console_owner --> &port_lock_key
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&port_lock_key);
lock(console_owner);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
The reason for this is a printk() in the i8259 interrupt chip driver
which is invoked with the irq descriptor lock held, which reverses the
lock operations vs. printk() from arbitrary contexts.
Switch the printk() to printk_deferred() to avoid that.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87365abt2v.fsf@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2286ba7d574ba3103a421a2f9ec17cb5b0d87a1 upstream.
Prevent setting the tscdeadline timer if the lapic is hw disabled.
Fixes: bce87cce88 (KVM: x86: consolidate different ways to test for in-kernel LAPIC)
Cc: <stable@vger.kernel.org>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1596165141-28874-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 372a8eaa05998cd45b3417d0e0ffd3a70978211a ]
The ORC unwinder fails to unwind newly forked tasks which haven't yet
run on the CPU. It correctly reads the 'ret_from_fork' instruction
pointer from the stack, but it incorrectly interprets that value as a
call stack address rather than a "signal" one, so the address gets
incorrectly decremented in the call to orc_find(), resulting in bad ORC
data.
Fix it by forcing 'ret_from_fork' frames to be signal frames.
Reported-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lkml.kernel.org/r/f91a8778dde8aae7f71884b5df2b16d552040441.1594994374.git.jpoimboe@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b344d6a83d01c52fddbefa6b3b4764da5b1022a0 ]
The kernel test bot reported[1] that using set_mask_bits on a u8 causes
the following issue on parisc:
hppa-linux-ld: drivers/phy/ti/phy-tusb1210.o: in function `tusb1210_probe':
>> (.text+0x2f4): undefined reference to `__cmpxchg_called_with_bad_pointer'
>> hppa-linux-ld: (.text+0x324): undefined reference to `__cmpxchg_called_with_bad_pointer'
hppa-linux-ld: (.text+0x354): undefined reference to `__cmpxchg_called_with_bad_pointer'
Add support for cmpxchg on u8 pointers.
[1] https://lore.kernel.org/patchwork/patch/1272617/#1468946
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Tested-by: Dave Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 05fb3dbda187bbd9cc1cd0e97e5d6595af570ac6 ]
Although iph is expected to point to at least 20 bytes of valid memory,
ihl may be bogus, for example on reception of a corrupt packet. If it
happens to be less than 5, we really don't want to run away and
dereference 16GB worth of memory until it wraps back to exactly zero...
Fixes: 0e455d8e80aa ("arm64: Implement optimised IP checksum helpers")
Reported-by: guodeqing <geffrey.guo@huawei.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 966a0acce2fca776391823381dba95c40e03c339 ]
Commit f7b93d42945c ("arm64/alternatives: use subsections for replacement
sequences") breaks LLVM's integrated assembler, because due to its
one-pass design, it cannot compute instruction sequence lengths before the
layout for the subsection has been finalized. This change fixes the build
by moving the .org directives inside the subsection, so they are processed
after the subsection layout is known.
Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences")
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1078
Link: https://lore.kernel.org/r/20200730153701.3892953-1-samitolvanen@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 04a8a3d0a73f51c7c2da84f494db7ec1df230e69 ]
The slow path for traced system call entries accessed a wrong memory
location to get the number of the maximum allowed system call number.
Renumber the numbered "local" label for the correct location to avoid
collisions with actual local labels.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Fixes: f3a8308864f920d2 ("sh: Add a few missing irqflags tracing markers.")
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit de2b41be8fcccb2f5b6c480d35df590476344201 ]
On x86-32 the idt_table with 256 entries needs only 2048 bytes. It is
page-aligned, but the end of the .bss..page_aligned section is not
guaranteed to be page-aligned.
As a result, objects from other .bss sections may end up on the same 4k
page as the idt_table, and will accidentially get mapped read-only during
boot, causing unexpected page-faults when the kernel writes to them.
This could be worked around by making the objects in the page aligned
sections page sized, but that's wrong.
Explicit sections which store only page aligned objects have an implicit
guarantee that the object is alone in the page in which it is placed. That
works for all objects except the last one. That's inconsistent.
Enforcing page sized objects for these sections would wreckage memory
sanitizers, because the object becomes artificially larger than it should
be and out of bound access becomes legit.
Align the end of the .bss..page_aligned and .data..page_aligned section on
page-size so all objects places in these sections are guaranteed to have
their own page.
[ tglx: Amended changelog ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200721093448.10417-1-joro@8bytes.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6a03469a1edc94da52b65478f1e00837add869a3 ]
With CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y, we compile the kernel with
-fdata-sections, which also splits the .bss section.
The new section, with a new .bss.* name, which pattern gets missed by the
main x86 linker script which only expects the '.bss' name. This results
in the discarding of the second part and a too small, truncated .bss
section and an unhappy, non-working kernel.
Use the common BSS_MAIN macro in the linker script to properly capture
and merge all the generated BSS sections.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20190415164956.124067-1-samitolvanen@google.com
[ Extended the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit eec13b42d41b0f3339dcf0c4da43734427c68620 upstream.
Unprivileged memory accesses generated by the so-called "translated"
instructions (e.g. LDRT) in kernel mode can cause user watchpoints to fire
unexpectedly. In such cases, the hw_breakpoint logic will invoke the user
overflow handler which will typically raise a SIGTRAP back to the current
task. This is futile when returning back to the kernel because (a) the
signal won't have been delivered and (b) userspace can't handle the thing
anyway.
Avoid invoking the user overflow handler for watchpoints triggered by
kernel uaccess routines, and instead single-step over the faulting
instruction as we would if no overflow handler had been installed.
Cc: <stable@vger.kernel.org>
Fixes: f81ef4a920c8 ("ARM: 6356/1: hw-breakpoint: add ARM backend for the hw-breakpoint framework")
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8c6de56a42e0c657955e12b882a81ef07d1d073e ]
kvm_steal_time_set_preempted() may accidentally clear KVM_VCPU_FLUSH_TLB
bit if it is called more than once while VCPU is preempted.
This is part of CVE-2019-3016.
(This bug was also independently discovered by Jim Mattson
<jmattson@google.com>)
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit be6577af0cef934ccb036445314072e8cb9217b9 upstream.
Stalls are quite frequent with recent kernels. I enabled
CONFIG_SOFTLOCKUP_DETECTOR and I caught the following stall:
watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [cc1:22803]
CPU: 0 PID: 22803 Comm: cc1 Not tainted 5.6.17+ #3
Hardware name: 9000/800/rp3440
IAOQ[0]: d_alloc_parallel+0x384/0x688
IAOQ[1]: d_alloc_parallel+0x388/0x688
RP(r2): d_alloc_parallel+0x134/0x688
Backtrace:
[<000000004036974c>] __lookup_slow+0xa4/0x200
[<0000000040369fc8>] walk_component+0x288/0x458
[<000000004036a9a0>] path_lookupat+0x88/0x198
[<000000004036e748>] filename_lookup+0xa0/0x168
[<000000004036e95c>] user_path_at_empty+0x64/0x80
[<000000004035d93c>] vfs_statx+0x104/0x158
[<000000004035dfcc>] __do_sys_lstat64+0x44/0x80
[<000000004035e5a0>] sys_lstat64+0x20/0x38
[<0000000040180054>] syscall_exit+0x0/0x14
The code was stuck in this loop in d_alloc_parallel:
4037d414: 0e 00 10 dc ldd 0(r16),ret0
4037d418: c7 fc 5f ed bb,< ret0,1f,4037d414 <d_alloc_parallel+0x384>
4037d41c: 08 00 02 40 nop
This is the inner loop of bit_spin_lock which is called by hlist_bl_unlock in
d_alloc_parallel:
static inline void bit_spin_lock(int bitnum, unsigned long *addr)
{
/*
* Assuming the lock is uncontended, this never enters
* the body of the outer loop. If it is contended, then
* within the inner loop a non-atomic test is used to
* busywait with less bus contention for a good time to
* attempt to acquire the lock bit.
*/
preempt_disable();
#if defined(CONFIG_SMP) || defined(CONFIG_DEBUG_SPINLOCK)
while (unlikely(test_and_set_bit_lock(bitnum, addr))) {
preempt_enable();
do {
cpu_relax();
} while (test_bit(bitnum, addr));
preempt_disable();
}
#endif
__acquire(bitlock);
}
After consideration, I realized that we must be losing bit unlocks.
Then, I noticed that we missed defining atomic64_set_release().
Adding this define fixes the stalls in bit operations.
Signed-off-by: Dave Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 81e96851ea32deb2c921c870eecabf335f598aeb ]
The clang integrated assembler requires the 'cmp' instruction to
have a length prefix here:
arch/x86/math-emu/wm_sqrt.S:212:2: error: ambiguous instructions require an explicit suffix (could be 'cmpb', 'cmpw', or 'cmpl')
cmp $0xffffffff,-24(%ebp)
^
Make this a 32-bit comparison, which it was clearly meant to be.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lkml.kernel.org/r/20200527135352.1198078-1-arnd@arndb.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5afc78551bf5d53279036e0bf63314e35631d79f ]
Rather than open-code test_tsk_thread_flag() at each callsite, simply
replace the couple of offenders with calls to test_tsk_thread_flag()
directly.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3beca48a45b5e0e6e6a4e0124276b8248dcc9bb ]
Quite some non OF/ACPI users of irqdomains allocate firmware nodes of type
IRQCHIP_FWNODE_NAMED or IRQCHIP_FWNODE_NAMED_ID and free them right after
creating the irqdomain. The only purpose of these FW nodes is to convey
name information. When this was introduced the core code did not store the
pointer to the node in the irqdomain. A recent change stored the firmware
node pointer in irqdomain for other reasons and missed to notice that the
usage sites which do the alloc_fwnode/create_domain/free_fwnode sequence
are broken by this. Storing a dangling pointer is dangerous itself, but in
case that the domain is destroyed later on this leads to a double free.
Remove the freeing of the firmware node after creating the irqdomain from
all affected call sites to cure this.
Fixes: 711419e504eb ("irqdomain: Add the missing assignment of domain->fwnode for named fwnode")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/873661qakd.fsf@nanos.tec.linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d5ab144429e8bd80889b856a44d56ab4a5cd59b ]
Increment *pos in the cpuinfo_op.next to fix the following warning
triggered by cat /proc/cpuinfo:
seq_file: buggy .next function c_next did not update position index
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 73f9941306d5ce030f3ffc7db425c7b2a798cf8e ]
Building xtensa kernel with gcc-10 produces the following warnings:
arch/xtensa/kernel/xtensa_ksyms.c:90:15: warning: conflicting types
for built-in function ‘__sync_fetch_and_and_4’;
expected ‘unsigned int(volatile void *, unsigned int)’
[-Wbuiltin-declaration-mismatch]
arch/xtensa/kernel/xtensa_ksyms.c:96:15: warning: conflicting types
for built-in function ‘__sync_fetch_and_or_4’;
expected ‘unsigned int(volatile void *, unsigned int)’
[-Wbuiltin-declaration-mismatch]
Fix declarations of these functions to avoid the warning.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This patch is to fix the backport of the upstream patch:
cc51e5428ea5 x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
When this was backported to the 4.9 and 4.14 stable branches the line
+ c->x86_cache_bits = c->x86_phys_bits;
was applied in the wrong place, being added to the
identify_cpu_without_cpuid() function instead of the get_cpu_cap()
function which it was correctly applied to in the 4.4 backport.
This means that x86_cache_bits is not set correctly resulting in the
following warning due to the cache bits being left uninitalised (zero).
WARNING: CPU: 0 PID: 7566 at arch/x86/kvm/mmu.c:284 kvm_mmu_set_mmio_spte_mask+0x4e/0x60 [kvm
Modules linked in: kvm_intel(+) kvm irqbypass ipv6 crc_ccitt binfmt_misc evdev lpc_ich mfd_core ioatdma pcc_cpufreq dca ena acpi_power_meter hwmon acpi_pad button ext4 crc16 mbcache jbd2 fscrypto nvme nvme_core dm_mirror dm_region_hash dm_log dm_mod dax
Hardware name: Amazon EC2 i3.metal/Not Specified, BIOS 1.0 10/16/2017
task: ffff88ff77704c00 task.stack: ffffc9000edac000
RIP: 0010:kvm_mmu_set_mmio_spte_mask+0x4e/0x60 [kvm
RSP: 0018:ffffc9000edafc60 EFLAGS: 00010206
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 00000000ffffff45
RDX: 000000000000002e RSI: 0008000000000001 RDI: 0008000000000001
RBP: ffffffffa036f000 R08: ffffffffffffff80 R09: ffffe8ffffccb3c0
R10: 0000000000000038 R11: 0000000000000000 R12: 0000000000005b80
R13: ffffffffa0370e40 R14: 0000000000000001 R15: ffff88bf7c0927e0
FS: 00007fa316f24740(0000) GS:ffff88bf7f600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa316ea0000 CR3: 0000003f7e986004 CR4: 00000000003606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
kvm_mmu_module_init+0x166/0x230 [kvm
kvm_arch_init+0x5d/0x150 [kvm
kvm_init+0x1c/0x2d0 [kvm
? hardware_setup+0x4a6/0x4a6 [kvm_intel
vmx_init+0x23/0x6aa [kvm_intel
? hardware_setup+0x4a6/0x4a6 [kvm_intel
do_one_initcall+0x3e/0x15d
do_init_module+0x5b/0x1e5
load_module+0x19e6/0x1dc0
? SYSC_init_module+0x13b/0x170
SYSC_init_module+0x13b/0x170
do_syscall_64+0x67/0x110
entry_SYSCALL_64_after_hwframe+0x41/0xa6
RIP: 0033:0x7fa316828f3a
RSP: 002b:00007ffc9d65c1f8 EFLAGS: 00000246 ORIG_RAX: 00000000000000af
RAX: ffffffffffffffda RBX: 00007fa316b08849 RCX: 00007fa316828f3a
RDX: 00007fa316b08849 RSI: 0000000000071328 RDI: 00007fa316e37000
RBP: 0000000000b47e80 R08: 0000000000000003 R09: 0000000000000000
R10: 00007fa316822dba R11: 0000000000000246 R12: 0000000000b46340
R13: 0000000000b464c0 R14: 0000000000000000 R15: 0000000000040000
Code: e9 65 06 00 75 25 48 b8 00 00 00 00 00 00 00 40 48 09 c6 48 09 c7 48 89 35 f8 65 06 00 48 89 3d f9 65 06 00 c3 0f 0b 0f 0b eb d2 <0f> 0b eb d7 0f 1f 40 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44
Fixes: 4.9.x ef3d45c95764 x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
Fixes: 4.14.x ec4034835eaf x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
Cc: stable@vger.kernel.org # 4.9.x-4.14.x
Signed-off-by: Suraj Jitindar Singh <surajjs@amazon.com>
Reviewed-by: Samuel Mendoza-Jonas <samjonas@amazon.com>
Reviewed-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a5a4366cecc25daa300b9a9174f7fdd352b9068 upstream.
Luis reports that, when reverse debugging with GDB, single-step does not
function as expected on arm64:
| I've noticed, under very specific conditions, that a PTRACE_SINGLESTEP
| request by GDB won't execute the underlying instruction. As a consequence,
| the PC doesn't move, but we return a SIGTRAP just like we would for a
| regular successful PTRACE_SINGLESTEP request.
The underlying problem is that when the CPU register state is restored
as part of a reverse step, the SPSR.SS bit is cleared and so the hardware
single-step state can transition to the "active-pending" state, causing
an unexpected step exception to be taken immediately if a step operation
is attempted.
In hindsight, we probably shouldn't have exposed SPSR.SS in the pstate
accessible by the GPR regset, but it's a bit late for that now. Instead,
simply prevent userspace from configuring the bit to a value which is
inconsistent with the TIF_SINGLESTEP state for the task being traced.
Cc: <stable@vger.kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Keno Fischer <keno@juliacomputing.com>
Link: https://lore.kernel.org/r/1eed6d69-d53d-9657-1fc9-c089be07f98c@linaro.org
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ed26aacfb5f71eecb20a ("mips: Add udelay lpj numbers adjustment")
has backported to 4.4~5.4, but the "struct cpufreq_freqs" (and also the
cpufreq notifier machanism) of 4.4~4.19 are different from the upstream
kernel. These differences cause build errors, and this patch can fix the
build.
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Stable <stable@vger.kernel.org> # 4.4/4.9/4.14/4.19
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|