diff options
| author | Michael Hennerich <michael.hennerich@analog.com> | 2010-03-09 20:38:45 -0800 |
|---|---|---|
| committer | Dmitry Torokhov <dmitry.torokhov@gmail.com> | 2010-03-09 22:12:45 -0800 |
| commit | 06a09124b5ec65f81df66c56695d9a9ae04a0114 (patch) | |
| tree | 6ae81521962ce1d013d00ae1d6915e528d8dc638 /drivers/input | |
| parent | 9e49f6c1339a7972e23a335c4c71a289b4c6f65b (diff) | |
Input: ads7846 - add support for AD7843 parts
The AD7873 is almost identical to the ADS7846; the only difference is
related to the Power Management bits PD0 and PD1. This results in a
slightly different PENIRQ enable behavior. For the AD7873, VREF should
be turned off during differential measurements.
So, add the AD7873/43 to the list of driver supported devices, and prevent
VREF usage during differential/ratiometric conversion modes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Diffstat (limited to 'drivers/input')
| -rw-r--r-- | drivers/input/touchscreen/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/input/touchscreen/ads7846.c | 10 |
2 files changed, 15 insertions, 4 deletions
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig index 7208654a94ae..8a8fa4d2d6a8 100644 --- a/drivers/input/touchscreen/Kconfig +++ b/drivers/input/touchscreen/Kconfig @@ -24,17 +24,18 @@ config TOUCHSCREEN_88PM860X module will be called 88pm860x-ts. config TOUCHSCREEN_ADS7846 - tristate "ADS7846/TSC2046 and ADS7843 based touchscreens" + tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens" depends on SPI_MASTER depends on HWMON = n || HWMON help Say Y here if you have a touchscreen interface using the - ADS7846/TSC2046 or ADS7843 controller, and your board-specific - setup code includes that in its table of SPI devices. + ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller, + and your board-specific setup code includes that in its + table of SPI devices. If HWMON is selected, and the driver is told the reference voltage on your board, you will also get hwmon interfaces for the voltage - (and on ads7846/tsc2046, temperature) sensors of this chip. + (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip. If unsure, say N (but it's safe to say "Y"). diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c index 8b05d8e97543..d187be05955f 100644 --- a/drivers/input/touchscreen/ads7846.c +++ b/drivers/input/touchscreen/ads7846.c @@ -36,6 +36,7 @@ * TSC2046 is just newer ads7846 silicon. * Support for ads7843 tested on Atmel at91sam926x-EK. * Support for ads7845 has only been stubbed in. + * Support for Analog Devices AD7873 and AD7843 tested. * * IRQ handling needs a workaround because of a shortcoming in handling * edge triggered IRQs on some platforms like the OMAP1/2. These @@ -984,6 +985,15 @@ static int __devinit ads7846_probe(struct spi_device *spi) vref = pdata->keep_vref_on; + if (ts->model == 7873) { + /* The AD7873 is almost identical to the ADS7846 + * keep VREF off during differential/ratiometric + * conversion modes + */ + ts->model = 7846; + vref = 0; + } + /* set up the transfers to read touchscreen state; this assumes we * use formula #2 for pressure, not #3. */ |