arm64: dts: qcom: db845c: Enable PCIe controllers

Enable the two PCIe controllers found on the Dragonboard845c.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

1 files changed, 91 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index 4a35ceb93c4c..9eb3bee45cd2 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -364,6 +364,39 @@
 	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
 };
 
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
+
+	vddpe-3v3-supply = <&pcie0_3p3v_dual>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_default_state>;
+};
+
+&pcie0_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&pcie1 {
+	status = "okay";
+	perst-gpio = <&tlmm 102 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default_state>;
+};
+
+&pcie1_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
 &pm8998_gpio {
 	vol_up_pin_a: vol-up-active {
 		pins = "gpio6";
@@ -406,6 +439,31 @@
 };
 
 &tlmm {
+	pcie0_default_state: pcie0-default {
+		clkreq {
+			pins = "gpio36";
+			function = "pci_e0";
+			bias-pull-up;
+		};
+
+		reset-n {
+			pins = "gpio35";
+			function = "gpio";
+
+			drive-strength = <2>;
+			output-low;
+			bias-pull-down;
+		};
+
+		wake-n {
+			pins = "gpio37";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	pcie0_pwren_state: pcie0-pwren {
 		pins = "gpio90";
 		function = "gpio";
@@ -414,6 +472,39 @@
 		bias-disable;
 	};
 
+	pcie1_default_state: pcie1-default {
+		perst-n {
+			pins = "gpio102";
+			function = "gpio";
+
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		clkreq {
+			pins = "gpio103";
+			function = "pci_e1";
+			bias-pull-up;
+		};
+
+		wake-n {
+			pins = "gpio11";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		reset-n {
+			pins = "gpio75";
+			function = "gpio";
+
+			drive-strength = <16>;
+			bias-pull-up;
+			output-high;
+		};
+	};
+
 	sdc2_default_state: sdc2-default {
 		clk {
 			pins = "sdc2_clk";