| Age | Commit message (Collapse) | Author |
|---|
|
The node names should be generic and DT schema expects certain pattern:
qcom/msm8998-oneplus-cheeseburger.dtb: leds: 'button-backlight' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
qcom/sc7180-trogdor-coachz-r1.dtb: pwmleds: 'keyboard-backlight' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221125144209.477328-1-krzysztof.kozlowski@linaro.org
|
|
The DBVDD and LDO1-IN supplies for rt5682 are required but are missing.
They are supplied by the same power rail as AVDD. Add them.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221102182002.255282-8-nfraprado@collabora.com
|
|
Update the fingerprint node on Trogdor to match the fingerprint DT
binding. This will allow us to drive the reset and boot gpios from the
driver when it is re-attached after flashing. We'll also be able to boot
the fingerprint processor if the BIOS isn't doing it for us.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221107191535.624371-3-swboyd@chromium.org
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Merge subnodes named 'pinconf' and 'pinmux' into one entry, add function
where missing (required by bindings for GPIOs) and reorganize overriding
pins by boards.
Split the SPI and UART configuration into separate nodes
1. SPI (MOSI, MISO, SCLK), SPI chip-select, SPI chip-select via GPIO,
2. UART per each pin: TX, RX and optional CTS/RTS.
This allows each board to customize them easily without adding any new
nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020225135.31750-4-krzysztof.kozlowski@linaro.org
|
|
SPI CS at bootup on trogdor"
This reverts commit e440e30e26dd6b0424002ad0ddcbbcea783efd85 because it
is not a reliable way of fixing SPI CS glitch and it depends on specific
Linux kernel pin controller driver behavior.
This behavior of kernel driver was changed in commit b991f8c3622c
("pinctrl: core: Handling pinmux and pinconf separately") thus
effectively the DTS fix stopped being effective.
Proper solution for the glitching SPI chip select must be implemented in
the drivers, not via ordering of entries in DTS, and is already
introduced in commit d21f4b7ffc22 ("pinctrl: qcom: Avoid glitching lines
when we first mux to output").
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020225135.31750-3-krzysztof.kozlowski@linaro.org
|
|
Add missing space or remove redundant one before opening {.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220919163333.129989-1-krzysztof.kozlowski@linaro.org
|
|
Add nodes for the onboard USB hub on trogdor devices. Remove the
'always-on' property from the hub regulator, since the regulator
is now managed by the onboard_usb_hub driver.
For anyone using trogdor-based devices on Linux, it should be
noted that this requires "CONFIG_USB_ONBOARD_HUB=y".
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220722093238.v24.1.I7a1a6448d50bdd38e6082204a9818c59cc7a9bfd@changeid
|
|
Both vdda-1p2-supply and vdda-0p9-supply regulators are controlled
by dp combo phy. Therefore remove them from dp controller.
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1656690436-15221-1-git-send-email-quic_khsieh@quicinc.com
|
|
detachables
Trogdor devices that have a detachable keyboard still have a
non-detachable keyboard input device present because we include the
cros-ec-keyboard.dtsi snippet in the top-level sc7180-trogdor.dtsi file
that every variant board includes. We do this because the
keyboard-controller node also provides some buttons like the power
button and volume buttons. Unfortunately, this means we register a
keyboard input device that doesn't do anything on boards with a
detachable keyboard.
Change the node's compatible on detachables to the newly introduced
"google,cros-ec-keyb-switches" compatible to indicate that there are
only switches and no keyboard to register. Similarly, move the keyboard
include that defines the keyboard-controller node out of
sc7180-trogdor.dtsi to boards that actually have a keyboard so that the
matrix properties are not defined on boards with the switches
compatible. Future boards can either use the include approach or the
node definition approach to describe a keyboard with possible switches
or just some switches.
Cc: Benson Leung <bleung@chromium.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220627212802.3593012-1-swboyd@chromium.org
|
|
Add common LED property - the function - to LED node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220607102931.102805-8-krzysztof.kozlowski@linaro.org
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-21-krzysztof.kozlowski@linaro.org
|
|
We don't use this carveout on trogdor boards, and having it defined in
the sc7180 SoC file causes an overlap message to be printed at boot.
OF: reserved mem: OVERLAP DETECTED!
memory@86000000 (0x0000000086000000--0x000000008ec00000) overlaps with memory@8b700000 (0x000000008b700000--0x000000008b710000)
Delete the node in the trogdor dtsi file to fix the overlap problem and
remove the error message.
Cc: Alex Elder <elder@linaro.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Fixes: 310b266655a3 ("arm64: dts: qcom: sc7180: define ipa_fw_mem node")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220517193307.3034602-1-swboyd@chromium.org
|
|
The SoC is always present on sc7180-trogdor.dtsi and thus we should
include it in the "generic" dtsi file for trogdor. Previously we had
removed it from there because we had to do the spi6/spi0 swizzle, so
each trogdor variant board had to include sc7180.dtsi and then
sc7180-trogdor.dtsi so that the latter dtsi file could modify the right
spi bus for EC and H1 properties that are common to all trogdor boards.
Now that we're done with that we can replace sc7180.dtsi includes with
sc7180-trogdor.dtsi and include sc7180.dtsi in sc7180-trogdor.dtsi as
was originally intended. We still need to include sc7180-trogdor.dtsi
before the bridge dtsi files though because those rely on the panel
label.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-4-swboyd@chromium.org
|
|
We had to do this spi0/spi6 flip-flop on trogdor-r0 because the spi
buses got swizzled between r0 and r1. The swizzle stopped after r1, but
we kept this around to support either hardware possibility and to keep
trogdor-r0 working.
trogdor-r0 isn't supported upstream, so this swizzle is not doing
anything besides making a pattern that others tryt to copy for the EC and
H1 nodes. Let's remove it and simplify the dts files.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-3-swboyd@chromium.org
|
|
Trogdor boards with a detachable keyboard don't have a trackpad over
i2c. Instead the trackpad is on the detachable keyboard base. Let's move
the enabling of the trackpad i2c bus out of the base sc7180-trogdor.dtsi
file so that each trogdor board that is detachable, of which there are
many, doesn't have to disable the trackpad bus.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-2-swboyd@chromium.org
|
|
The SAR node, ap_sar_sensor, needs to be enabled in addition to the i2c
bus it resides on. Let's simplify this by leaving the sensor node
enabled by default while leaving the i2c bus disabled by default. On
boards that use the sensor, we already enable the i2c bus so we can
simply remove the extra bit that enables the sar sensor node. This saves
some lines but is otherwise a non-functional change.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220325211640.54228-1-swboyd@chromium.org
|
|
dtschema expects PWM node name to be a generic "pwm". This also matches
Devicetree specification requirements about generic node names.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220214081916.162014-4-krzysztof.kozlowski@canonical.com
|
|
All of the other fixed regulators have the "-regulator" suffix. Add it
to pp3300_hub to match.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.1.I7b284531f1c992932f7eef8abaf7cc5548064f33@changeid
|
|
Some trogdor boards have on-board regulators for the MIPI camera
components. Add nodes describing these regulators so boards with these
supplies can consume them.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211216044529.733652-1-swboyd@chromium.org
|
|
MSM DSI host driver actually parses "data-lanes" in DT and compare
it with the number of DSI lanes the bridge driver sets for
mipi_dsi_device. So we need to always specify "data-lanes" for the
DSI host output. As of now, "data-lanes" is added to ti-sn65dsi86 dts
fragment, but missing in parade-ps8640 dts fragment, which requires
a fixup.
Since we'll do 4-lane DSI regardless of which bridge chip is used,
instead of adding "data-lanes" to parade-ps8640 dts fragment, let's
just move "data-lanes" from the bridge dts to sc7180-trogdor.dtsi.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211029152647.v3.2.If23c83a786fc4d318a1986f43803f22b4b1d82cd@changeid
|
|
Pull ARM SoC DT updates from Arnd Bergmann:
"This is a rather large update for the ARM devicetree files, after a
few quieter releases, with 775 total commits and 47 branches pulled
into this one.
There are 5 new SoC types plus some minor variations, and a total of
60 new machines, so I'm limiting the summary to the main noteworthy
items:
- Apple M1 gain support for PCI and pinctrl, getting a bit closer to
a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
SM7225, 11 new smartphones, and three additional Chromebooks, and
improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version of
their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
of improvements for the recently added SAMA7 family. The LAN966 SoC
that was added in the platform code does not have dts files yet.
Two board files are added for the older at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600 as
BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new development
boards using RK3328/RK3399/RK3566, and one Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the new
MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
readers, and three additional development boards, which is notably
less than their usual additions, but they also gain improvements to
their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with a
reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many updates
for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for more
hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub home
automation controllers, along with changes to other machines
- Rob Herring continues his work on fixing dtc warnings all over the
tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc"
* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
arm64: dts: apple: t8103: Add root port interrupt routing
arm64: dts: apple: t8103: Add PCIe DARTs
arm64: apple: Add PCIe node
arm64: apple: Add pinctrl nodes
ARM: dts: arm: Update ICST clock nodes 'reg' and node names
ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
arm64: dts: exynos: add chipid node for exynosautov9 SoC
ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
arm64: dts: qcom: sm8350: Add CPU topology and idle-states
arm64: dts: qcom: Drop unneeded extra device-specific includes
arm64: dts: qcom: msm8916: Drop standalone smem node
arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
...
|
|
Factor out ti-sn65dsi86 edp bridge as a separate dts fragment.
This helps us introduce the second source edp bridge later.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008113839.v3.1.Ibada67e75d2982157e64164f1d11715d46cdc42c@changeid
|
|
The current drive strength values are not sufficient on non discrete
boards and this leads to CRC errors during switching to HS400 enhanced
strobe mode.
Hardware simulation results on non discrete boards shows up that use the
maximum drive strength values for data and command lines could helps
in avoiding these CRC errors.
So, update data and command line drive strength values to maximum.
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1629132650-26277-1-git-send-email-sbhanu@codeaurora.org
|
|
Enable the IPA node for LTE and skip for wifi-only SKUs
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210920113220.v1.1.I904da9664f294fcf222f6f378d37eaadd72ca92e@changeid
|
|
This should be the dai for display port. Without this set properly we
fail to get audio routed through external displays on trogdor. It looks
like we picked up v4[1] of this patch when there was a v7[2]. The v7
patch still had the wrong sound-dai but at least we can fix all this up
and audio works.
Cc: Srinivasa Rao Mandadapu <srivasam@qti.qualcomm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: b22d313e1772 ("arm64: dts: qcom: sc7180-trogdor: Add lpass dai link for HDMI")
Link: https://lore.kernel.org/r/20210721080549.28822-3-srivasam@qti.qualcomm.com [1]
Link: https://lore.kernel.org/r/20210726120910.20335-3-srivasam@codeaurora.org [2]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210811224141.1110495-1-swboyd@chromium.org
|
|
Putting the panel under the bridge chip (under the aux-bus node)
allows the panel driver to get access to the DP AUX bus, enabling all
sorts of fabulous new features.
While we're at this, get rid of a level of hierarchy for the panel
node. It doesn't need "ports / port" and can just have a "port" child.
For Linux, this patch has a hard requirement on the patches adding DP
AUX bus support to the ti-sn65dsi86 bridge chip driver. See the patch
("drm/bridge: ti-sn65dsi86: Add support for the DP AUX bus").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210611101711.v10.11.Ibdb7735fb1844561b902252215a69526a14f9abd@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add dai link in sc7180-trogdor.dtsi for supporting audio over DP
Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@qti.qualcomm.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210721080549.28822-3-srivasam@qti.qualcomm.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Use max98360a dts node to correctly describe the hardware.
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210625045010.2914289-1-judyhsiao@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add DP device node on sc7180.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1622758940-13485-1-git-send-email-khsieh@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This spi flash part is actually being clocked at 37.5MHz, not 25MHz,
because of the way the clk driver is rounding up the rate that is
requested to the nearest supported frequency. Let's update the frequency
here, and remove the TODO because this is the fastest frequency we're
going to be able to use here.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210519054030.3217704-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This compatible string isn't present upstream. Let's drop the node as it
isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601185959.3101132-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
We don't use the PON module on Trogdor devices. Instead the reboot
reason is sort of stored in the 'eventlog' and the bootloader figures
out if the boot is abnormal and records that there. Disable the PON node
and then drop the power key disabling because that's a child node that
will no longer be enabled if the PON node is disabled.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601184417.3020834-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
On coachz it could be observed that SPI_CLK voltage level was only
1.4V during active transfers because the drive strength was too
weak. The line hadn't finished slewing up by the time we started
driving it down again. Using a drive strength of 8 lets us achieve the
correct voltage level of 1.8V.
Though the worst problems were observed on coachz hardware, let's do
this across the board for trogdor devices. Scoping other boards shows
that this makes the clk line look nicer on them too and doesn't
introduce any problems.
Only the clk line is adjusted, not any data lines. Because SPI isn't a
DDR protocol we only sample the data lines on either rising or falling
edges, not both. That means the clk line needs to toggle twice as fast
as data lines so having the higher drive strength is more important
there.
Signed-off-by: Wenchao Han <hanwenchao@huaqin.corp-partner.google.com>
[dianders: Adjust author real name; adjust commit message]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210510075253.1.Ib4c296d6ff9819f26bcaf91e8a08729cc203fed0@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Some SC7180 based boards do not have external pull-up for cd-gpio.
Set this pin to internal pull-up for sleep config to avoid frequent
regulator toggle events.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210602121313.v3.2.I52f30ddfe62041b7e6c3c362f0ad8f695ac28224@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Move sdc1/sdc2 pinconf from SoC specific DT file to board specific DT
files
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210602121313.v3.1.Ia83c80aec3b9535f01441247b6c3fb6f80b0ec7f@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Adds label for MI2S secondary block to allow follower projects to override
for the four speaker support which uses I2S SD1 line on gpio52 pin.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20210601022117.4071117-1-judyhsiao@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be wasting power
powering hpd when we don't use it on trogdor boards. We didn't notice
this before because the kernel driver blindly disables hpd, but that
won't be true for much longer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 7ec3e67307f8 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324025534.1837405-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
qcom camera driver allocates the ICP firmware memory
dynamically, so the carveout region is unnecessary.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Link: https://lore.kernel.org/r/20210525133242.188603-1-senozhatsky@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Move rmtfs memory region so that it does not overlap with system
RAM (kernel data) when KAsan is enabled. This puts rmtfs right
after mba_mem which is not supposed to increase beyond 0x94600000
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210330014610.1451198-1-sujitka@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add dai link for supporting lpass I2S driver, which is used
for audio capture and playback.
Add lpass-cpu node with pin controls and i2s primary
and secondary dai-links.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ajit Pandey <ajitp@codeaurora.org>
Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/20210314061054.19451-2-srivasam@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This moved from being trogdor specific to being part of the general
sc7180.dtsi SoC file in commit 681a607ad21a ("arm64: dts: qcom:
sc7180: Add DisplayPort HPD pin dt node"). Then we dropped the pinconf
from the general sc7180.dtsi file in commit 8d079bf20410 ("arm64: dts:
qcom: sc7180: Drop pinconf on dp_hot_plug_det") and added it back to
the trogdor dts file in commit f772081f4883 ("arm64: dts: qcom:
sc7180: Add "dp_hot_plug_det" pinconf for trogdor").
As part of this we managed to forget to drop the old copy in the
trogdor dts. Let's do it now.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[dianders: updated desc]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210311131008.1.I85fc8146c0ee47e261faa0c54dd621467b81952d@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
At boot time the following happens:
1. Device core gets ready to probe our SPI driver.
2. Device core applies SPI controller's "default" pinctrl.
3. Device core calls the SPI driver's probe() function which will
eventually setup the chip select GPIO as "unasserted".
Thinking about the above, we can find:
a) For SPI devices that the BIOS inits (Cr50 and EC), the BIOS would
have had them configured as "GENI" pins and not as "GPIO" pins.
b) It turns out that our BIOS also happens to init these pins as
"output" (even though it doesn't need to since they're not muxed as
GPIO) but leaves them at the default state of "low".
c) As soon as we apply the "default" chip select it'll switch the
function to GPIO and stop driving the chip select high (which is
how "GENI" was driving it) and start driving it low.
d) As of commit 9378f46040be ("UPSTREAM: spi: spi-geni-qcom: Use the
new method of gpio CS control"), when the SPI core inits things it
inits the GPIO to be "deasserted". Prior to that commit the GPIO
was left untouched until first use.
e) When the first transaction happens we'll assert the chip select and
then deassert it after done.
So before the commit to change us to use gpio descriptors we used to
have a _really long_ assertion of chip select before our first
transaction (because it got pulled down and then the first "assert"
was a no-op). That wasn't great but (apparently) didn't cause any
real harm.
After the commit to change us to use gpio descriptors we end up
glitching the chip select line during probe. It would go low and then
high with no data transferred. The other side ought to be robust
against this, but it certainly could cause some confusion. It's known
to at least cause an error message on the EC console and it's believed
that, under certain timing conditions, it could be getting the EC into
a confused state causing the EC driver to fail to probe.
Let's fix things to avoid the glitch. We'll add an extra pinctrl
entry that sets the value of the pin to output high (CS deasserted)
before doing anything else. We'll do this in its own pinctrl node
that comes before the normal pinctrl entries to ensure that the order
is correct and that this gets applied before the mux change.
This change is in the trogdor board file rather than in the SoC dtsi
file because chip select polarity can be different depending on what's
hooked up and it doesn't feel worth it to spam the SoC dtsi file with
both options. The board file would need to pick the right one anyway.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: cfbb97fde694 ("arm64: dts: qcom: Switch sc7180-trogdor to control SPI CS via GPIO")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210218145456.1.I1da01a075dd86e005152f993b2d5d82dd9686238@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Removed voting for RPMH_RF_CLK2 which is not required as it is
getting managed by BT SoC through SW_CTRL line.
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.8.I80c268f163e6d49a70af1238be442b5de400c579@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Removed the pinctrl and pin{mux,conf} for the control pins because:
1. The only need for them is for userspace control via flash_fp_mcu
2. cros-ec doesn't know what to do with them, and even if it did,
it would interfere with flash_fp_mcu at the most inopportune times
Since we're not using hogs, we rely on AP firmware to set all the
control pins correctly.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Craig Hesling <hesling@chromium.org>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
[dianders: adjusted since coachz isn't upstream yet]
Reviewed-by; Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.7.Ifd7b86f826b18410eada75758a7bca1eebfa336d@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
We only want to use this clk driver on CoachZ devices. Disable it for
all other Trogdor boards. NOTE: CoachZ devices aren't yet supported
upstream so until it is this is just disabled for all trogdor.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[dianders:adjusted since no coachz upstream yet]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.6.I22522b0c9db505ee43ed08e8d5d9e8fe632e7447@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Configure the pen to be a wakeup source only when the pen is ejected
instead of both when the pen is ejected and inserted. This corresponds
to wake source requirements.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.5.Ib9672bfbe639c96c85408d6f0217a2609eb0b70f@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Let's avoid a bit of duplication by pushing this up to the trogdor.dtsi
file.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.4.I1483fac4c5ae4b2d7660290ff85d69945292618f@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The trackpad interrupt got renamed and also moved to a new GPIO on
newer boards. Let's do the move in the "trogdor.dtsi" file and then
undo it in the two old boards.
NOTE: since none of the new boards have device trees yet, this change
looks silly on its own but it will make sense after more boards are
supported.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.3.Iddf6dc8102aa4fbc3847936226fc7bf2e2cd315c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
In general pinconf belongs in board files, not SoC files. Move it to
the only current user (trogdor). Also adjust the drive strengths and
pulls.
Cc: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Cc: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Cc: Tzung-Bi Shih <tzungbi@chromium.org>
Cc: Judy Hsiao <judyhsiao@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210301133318.v2.2.Id27e7e6f90c29bf623fa4880e18a14ba1dffd2d2@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
charger temperature
On trogdor the ADC thermal monitor is used for monitoring certain
device temperatures. All trogdor boards have at least a thermistor
for the charger temperature, optionally they may have others.
Currently the ADC thermal monitor is configured to use channel 1
for the charger temperature. Given that all trogdor boards have
the charger thermistor it makes more sense to use channel 0,
and then let boards with other thermistors use channels 1, 2, 3,
rather than 0, 2, 3.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210225103330.v2.4.I67e29f2854bad22e3581d6a6e1879b9fc8abbdea@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
