Merge remote-tracking branch 'spi/for-next'

4 files changed, 98 insertions, 38 deletions

diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt
index dc975064fa27..64ee489571c4 100644
--- a/Documentation/devicetree/bindings/spi/sh-msiof.txt
+++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt
@@ -38,6 +38,8 @@ Optional properties:
 			 specifiers, one for transmission, and one for
 			 reception.
 - dma-names            : Must contain a list of two DMA names, "tx" and "rx".
+- spi-slave            : Empty property indicating the SPI controller is used
+			 in slave mode.
 - renesas,dtdl         : delay sync signal (setup) in transmit mode.
 			 Must contain one of the following values:
 			 0   (no bit delay)
diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt
index 4b1d6e74c744..1f6e86f787ef 100644
--- a/Documentation/devicetree/bindings/spi/spi-bus.txt
+++ b/Documentation/devicetree/bindings/spi/spi-bus.txt
@@ -1,17 +1,23 @@
 SPI (Serial Peripheral Interface) busses
 
-SPI busses can be described with a node for the SPI master device
-and a set of child nodes for each SPI slave on the bus.  For this
-discussion, it is assumed that the system's SPI controller is in
-SPI master mode.  This binding does not describe SPI controllers
-in slave mode.
+SPI busses can be described with a node for the SPI controller device
+and a set of child nodes for each SPI slave on the bus.  The system's SPI
+controller may be described for use in SPI master mode or in SPI slave mode,
+but not for both at the same time.
 
-The SPI master node requires the following properties:
+The SPI controller node requires the following properties:
+- compatible      - Name of SPI bus controller following generic names
+		    recommended practice.
+
+In master mode, the SPI controller node requires the following additional
+properties:
 - #address-cells  - number of cells required to define a chip select
 		address on the SPI bus.
 - #size-cells     - should be zero.
-- compatible      - name of SPI bus controller following generic names
-		recommended practice.
+
+In slave mode, the SPI controller node requires one additional property:
+- spi-slave       - Empty property.
+
 No other properties are required in the SPI bus node.  It is assumed
 that a driver for an SPI bus device will understand that it is an SPI bus.
 However, the binding does not attempt to define the specific method for
@@ -21,7 +27,7 @@ assumption that board specific platform code will be used to manage
 chip selects.  Individual drivers can define additional properties to
 support describing the chip select layout.
 
-Optional properties:
+Optional properties (master mode only):
 - cs-gpios	  - gpios chip select.
 - num-cs	  - total number of chipselects.
 
@@ -41,28 +47,36 @@ cs1 : native
 cs2 : &gpio1 1 0
 cs3 : &gpio1 2 0
 
-SPI slave nodes must be children of the SPI master node and can
-contain the following properties.
-- reg             - (required) chip select address of device.
-- compatible      - (required) name of SPI device following generic names
-		recommended practice.
-- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz.
-- spi-cpol        - (optional) Empty property indicating device requires
-		inverse clock polarity (CPOL) mode.
-- spi-cpha        - (optional) Empty property indicating device requires
-		shifted clock phase (CPHA) mode.
-- spi-cs-high     - (optional) Empty property indicating device requires
-		chip select active high.
-- spi-3wire       - (optional) Empty property indicating device requires
-		3-wire mode.
-- spi-lsb-first   - (optional) Empty property indicating device requires
-		LSB first mode.
-- spi-tx-bus-width - (optional) The bus width (number of data wires) that is
-                      used for MOSI. Defaults to 1 if not present.
-- spi-rx-bus-width - (optional) The bus width (number of data wires) that is
-                      used for MISO. Defaults to 1 if not present.
-- spi-rx-delay-us  - (optional) Microsecond delay after a read transfer.
-- spi-tx-delay-us  - (optional) Microsecond delay after a write transfer.
+
+SPI slave nodes must be children of the SPI controller node.
+
+In master mode, one or more slave nodes (up to the number of chip selects) can
+be present.  Required properties are:
+- compatible      - Name of SPI device following generic names recommended
+		    practice.
+- reg             - Chip select address of device.
+- spi-max-frequency - Maximum SPI clocking speed of device in Hz.
+
+In slave mode, the (single) slave node is optional.
+If present, it must be called "slave".  Required properties are:
+- compatible      - Name of SPI device following generic names recommended
+		    practice.
+
+All slave nodes can contain the following optional properties:
+- spi-cpol        - Empty property indicating device requires inverse clock
+		    polarity (CPOL) mode.
+- spi-cpha        - Empty property indicating device requires shifted clock
+		    phase (CPHA) mode.
+- spi-cs-high     - Empty property indicating device requires chip select
+		    active high.
+- spi-3wire       - Empty property indicating device requires 3-wire mode.
+- spi-lsb-first   - Empty property indicating device requires LSB first mode.
+- spi-tx-bus-width - The bus width (number of data wires) that is used for MOSI.
+		    Defaults to 1 if not present.
+- spi-rx-bus-width - The bus width (number of data wires) that is used for MISO.
+		    Defaults to 1 if not present.
+- spi-rx-delay-us - Microsecond delay after a read transfer.
+- spi-tx-delay-us - Microsecond delay after a write transfer.
 
 Some SPI controllers and devices support Dual and Quad SPI transfer mode.
 It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4
diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt
index dc6d0313324a..825c39cae74a 100644
--- a/Documentation/devicetree/bindings/spi/spi-meson.txt
+++ b/Documentation/devicetree/bindings/spi/spi-meson.txt
@@ -20,3 +20,34 @@ Required properties:
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
+
+* SPICC (SPI Communication Controller)
+
+The Meson SPICC is generic SPI controller for general purpose Full-Duplex
+communications with dedicated 16 words RX/TX PIO FIFOs.
+
+Required properties:
+ - compatible: should be "amlogic,meson-gx-spicc" on Amlogic GX SoCs.
+ - reg: physical base address and length of the controller registers
+ - interrupts: The interrupt specifier
+ - clock-names: Must contain "core"
+ - clocks: phandle of the input clock for the baud rate generator
+ - #address-cells: should be 1
+ - #size-cells: should be 0
+
+Optional properties:
+ - resets: phandle of the internal reset line
+
+See ../spi/spi-bus.txt for more details on SPI bus master and slave devices
+required and optional properties.
+
+Example :
+	spi@c1108d80 {
+		compatible = "amlogic,meson-gx-spicc";
+		reg = <0xc1108d80 0x80>;
+		interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "core";
+		clocks = <&clk81>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary
index d1824b399b2d..1721c1b570c3 100644
--- a/Documentation/spi/spi-summary
+++ b/Documentation/spi/spi-summary
@@ -62,8 +62,8 @@ chips described as using "three wire" signaling: SCK, data, nCSx.
 (That data line is sometimes called MOMI or SISO.)
 
 Microcontrollers often support both master and slave sides of the SPI
-protocol.  This document (and Linux) currently only supports the master
-side of SPI interactions.
+protocol.  This document (and Linux) supports both the master and slave
+sides of SPI interactions.
 
 
 Who uses it?  On what kinds of systems?
@@ -154,9 +154,8 @@ control audio interfaces, present touchscreen sensors as input interfaces,
 or monitor temperature and voltage levels during industrial processing.
 And those might all be sharing the same controller driver.
 
-A "struct spi_device" encapsulates the master-side interface between
-those two types of driver.  At this writing, Linux has no slave side
-programming interface.
+A "struct spi_device" encapsulates the controller-side interface between
+those two types of drivers.
 
 There is a minimal core of SPI programming interfaces, focussing on
 using the driver model to connect controller and protocol drivers using
@@ -177,10 +176,24 @@ shows up in sysfs in several locations:
    /sys/bus/spi/drivers/D ... driver for one or more spi*.* devices
 
    /sys/class/spi_master/spiB ... symlink (or actual device node) to
-	a logical node which could hold class related state for the
-	controller managing bus "B".  All spiB.* devices share one
+	a logical node which could hold class related state for the SPI
+	master controller managing bus "B".  All spiB.* devices share one
 	physical SPI bus segment, with SCLK, MOSI, and MISO.
 
+   /sys/devices/.../CTLR/slave ... virtual file for (un)registering the
+	slave device for an SPI slave controller.
+	Writing the driver name of an SPI slave handler to this file
+	registers the slave device; writing "(null)" unregisters the slave
+	device.
+	Reading from this file shows the name of the slave device ("(null)"
+	if not registered).
+
+   /sys/class/spi_slave/spiB ... symlink (or actual device node) to
+	a logical node which could hold class related state for the SPI
+	slave controller on bus "B".  When registered, a single spiB.*
+	device is present here, possible sharing the physical SPI bus
+	segment with other SPI slave devices.
+
 Note that the actual location of the controller's class state depends
 on whether you enabled CONFIG_SYSFS_DEPRECATED or not.  At this time,
 the only class-specific state is the bus number ("B" in "spiB"), so