1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
|
/*
* Copyright (c) 2016, ARM Limited and Contributors. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* Redistributions of source code must retain the above copyright notice, this
* list of conditions and the following disclaimer.
*
* Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* Neither the name of ARM nor the names of its contributors may be used
* to endorse or promote products derived from this software without specific
* prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
#include <arch_helpers.h>
#include <assert.h>
#include <debug.h>
#include <delay_timer.h>
#include <mmio.h>
#include <m0_ctl.h>
#include <plat_private.h>
#include <rk3399_def.h>
#include <secure.h>
#include <soc.h>
void m0_init(void)
{
/* secure config for M0 */
mmio_write_32(SGRF_BASE + SGRF_PMU_CON(0), WMSK_BIT(7));
mmio_write_32(SGRF_BASE + SGRF_SOC_CON(6), WMSK_BIT(12));
/* set the execute address for M0 */
mmio_write_32(SGRF_BASE + SGRF_PMU_CON(3),
BITS_WITH_WMASK((M0_BINCODE_BASE >> 12) & 0xffff,
0xffff, 0));
mmio_write_32(SGRF_BASE + SGRF_PMU_CON(7),
BITS_WITH_WMASK((M0_BINCODE_BASE >> 28) & 0xf,
0xf, 0));
/* document is wrong, PMU_CRU_GATEDIS_CON0 do not need set MASK BIT */
mmio_setbits_32(PMUCRU_BASE + PMUCRU_GATEDIS_CON0, 0x02);
/*
* To switch the parent to xin24M and div == 1,
*
* We need to close most of the PLLs and clocks except the OSC 24MHz
* durning suspend, and this should be enough to supplies the ddrfreq,
* For the simple handle, we just keep the fixed 24MHz to supply the
* suspend and ddrfreq directly.
*/
mmio_write_32(PMUCRU_BASE + PMUCRU_CLKSEL_CON0,
BIT_WITH_WMSK(15) | BITS_WITH_WMASK(0x0, 0x1f, 8));
mmio_write_32(PMUCRU_BASE + PMUCRU_CLKGATE_CON2, WMSK_BIT(5));
}
void m0_start(void)
{
/* enable clocks for M0 */
mmio_write_32(PMUCRU_BASE + PMUCRU_CLKGATE_CON2,
BITS_WITH_WMASK(0x0, 0xf, 0));
/* clean the PARAM_M0_DONE flag, mean that M0 will start working */
mmio_write_32(M0_PARAM_ADDR + PARAM_M0_DONE, 0);
dmbst();
mmio_write_32(PMUCRU_BASE + PMUCRU_SOFTRST_CON0,
BITS_WITH_WMASK(0x0, 0x4, 0));
udelay(5);
/* start M0 */
mmio_write_32(PMUCRU_BASE + PMUCRU_SOFTRST_CON0,
BITS_WITH_WMASK(0x0, 0x20, 0));
dmbst();
}
void m0_stop(void)
{
/* stop M0 */
mmio_write_32(PMUCRU_BASE + PMUCRU_SOFTRST_CON0,
BITS_WITH_WMASK(0x24, 0x24, 0));
/* disable clocks for M0 */
mmio_write_32(PMUCRU_BASE + PMUCRU_CLKGATE_CON2,
BITS_WITH_WMASK(0xf, 0xf, 0));
}
void m0_wait_done(void)
{
do {
/*
* Don't starve the M0 for access to SRAM, so delay before
* reading the PARAM_M0_DONE value again.
*/
udelay(5);
dsb();
} while (mmio_read_32(M0_PARAM_ADDR + PARAM_M0_DONE) != M0_DONE_FLAG);
/*
* Let the M0 settle into WFI before we leave. This is so we don't reset
* the M0 in a bad spot which can cause problems with the M0.
*/
udelay(10);
dsb();
}
|
