| Age | Commit message (Collapse) | Author |
|---|
|
Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.
Early demux is supposed to be an optimization, we should avoid spending
too much time in it.
It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.
10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.
Fixes: 421b3885bf6d5 ("udp: ipv4: Add udp early demux")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Held <drheld@google.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers
Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stephen hemminger <stephen@networkplumber.org>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hari's been doing the patch submissions for a while now and he'll be
taking over as maintainer.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
"This pull request is later than I'd have liked because I was waiting
for some performance data to help finally justify sending the
long-standing dm-crypt cpu scalability improvements upstream.
Unfortunately we came up short, so those dm-crypt changes will
continue to wait, but it seems we're not far off.
. Add dm_accept_partial_bio interface to DM core to allow DM targets
to only process a portion of a bio, the remainder being sent in the
next bio. This enables the old dm snapshot-origin target to only
split write bios on chunk boundaries, read bios are now sent to the
origin device unchanged.
. Add DM core support for disabling WRITE SAME if the underlying SCSI
layer disables it due to command failure.
. Reduce lock contention in DM's bio-prison.
. A few small cleanups and fixes to dm-thin and dm-era"
* tag 'dm-3.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: update discard_granularity to reflect the thin-pool blocksize
dm bio prison: implement per bucket locking in the dm_bio_prison hash table
dm: remove symbol export for dm_set_device_limits
dm: disable WRITE SAME if it fails
dm era: check for a non-NULL metadata object before closing it
dm thin: return ENOSPC instead of EIO when error_if_no_space enabled
dm thin: cleanup noflush_work to use a proper completion
dm snapshot: do not split read bios sent to snapshot-origin target
dm snapshot: allocate a per-target structure for snapshot-origin target
dm: introduce dm_accept_partial_bio
dm: change sector_count member in clone_info from sector_t to unsigned
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull more PCI updates from Bjorn Helgaas:
"Here are some more things I'd like to see in v3.16-rc1:
- DMA alias iterator, part of some work to fix IOMMU issues
- MVEBU, Tegra, DesignWare changes that I forgot to include before
- Some whitespace code cleanup
Details:
IOMMU
- Add DMA alias iterator (Alex Williamson)
- Add DMA alias quirks for ASMedia, ITE, Tundra bridges (Alex Williamson)
- Add DMA alias quirks for Marvell, Ricoh devices (Alex Williamson)
- Add DMA alias quirk for HighPoint devices (Jérôme Carretero)
MSI
- Fix leak in free_msi_irqs() (Alexei Starovoitov)
Marvell MVEBU
- Remove unnecessary use of 'conf_lock' spinlock (Andrew Murray)
- Avoid setting an undefined window size (Jason Gunthorpe)
- Allow several windows with the same target/attribute (Thomas Petazzoni)
- Split PCIe BARs into multiple MBus windows when needed (Thomas Petazzoni)
- Fix off-by-one in the computed size of the mbus windows (Willy Tarreau)
NVIDIA Tegra
- Use new OF interrupt mapping when possible (Lucas Stach)
Synopsys DesignWare
- Remove unnecessary use of 'conf_lock' spinlock (Andrew Murray)
- Use new OF interrupt mapping when possible (Lucas Stach)
- Split Exynos and i.MX bindings (Lucas Stach)
- Fix comment for setting number of lanes (Mohit Kumar)
- Fix iATU programming for cfg1, io and mem viewport (Mohit Kumar)
Miscellaneous
- EXPORT_SYMBOL cleanup (Ryan Desfosses)
- Whitespace cleanup (Ryan Desfosses)
- Merge multi-line quoted strings (Ryan Desfosses)"
* tag 'pci-v3.16-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (21 commits)
PCI: Add function 1 DMA alias quirk for HighPoint RocketRaid 642L
PCI/MSI: Fix memory leak in free_msi_irqs()
PCI: Merge multi-line quoted strings
PCI: Whitespace cleanup
PCI: Move EXPORT_SYMBOL so it immediately follows function/variable
PCI: Add bridge DMA alias quirk for ITE bridge
PCI: designware: Split Exynos and i.MX bindings
PCI: Add bridge DMA alias quirk for ASMedia and Tundra bridges
PCI: Add support for PCIe-to-PCI bridge DMA alias quirks
PCI: Add function 1 DMA alias quirk for Marvell devices
PCI: Add function 0 DMA alias quirk for Ricoh devices
PCI: Add support for DMA alias quirks
PCI: Convert pci_dev_flags definitions to bit shifts
PCI: Add DMA alias iterator
PCI: mvebu: Use '%pa' for printing 'phys_addr_t' type
PCI: mvebu: Remove unnecessary use of 'conf_lock' spinlock
PCI: designware: Remove unnecessary use of 'conf_lock' spinlock
PCI: designware: Use new OF interrupt mapping when possible
PCI: designware: Fix iATU programming for cfg1, io and mem viewport
PCI: designware: Fix comment for setting number of lanes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are fixups on top of the previous PM+ACPI pull request,
regression fixes (ACPI hotplug, cpufreq ppc-corenet), other bug fixes
(ACPI reset, cpufreq), new PM trace points for system suspend
profiling and a copyright notice update.
Specifics:
- I didn't remember correctly that the Hans de Goede's ACPI video
patches actually didn't flip the video.use_native_backlight
default, although we had discussed that and decided to do that.
Since I said we would do that in the previous PM+ACPI pull request,
make that change for real now.
- ACPI bus check notifications for PCI host bridges don't cause the
bus below the host bridge to be checked for changes as they should
because of a mistake in the ACPI-based PCI hotplug (ACPIPHP)
subsystem that forgets to add hotplug contexts to PCI host bridge
ACPI device objects. Create hotplug contexts for PCI host bridges
too as appropriate.
- Revert recent cpufreq commit related to the big.LITTLE cpufreq
driver that breaks arm64 builds.
- Fix for a regression in the ppc-corenet cpufreq driver introduced
during the 3.15 cycle and causing the driver to use the remainder
from do_div instead of the quotient. From Ed Swarthout.
- Resets triggered by panic activate a BUG_ON() in vmalloc.c on
systems where the ACPI reset register is located in memory address
space. Fix from Randy Wright.
- Fix for a problem with cpufreq governors that decisions made by
them may be suboptimal due to the fact that deferrable timers are
used by them for CPU load sampling. From Srivatsa S Bhat.
- Fix for a problem with the Tegra cpufreq driver where the CPU
frequency is temporarily switched to a "stable" level that is
different from both the initial and target frequencies during
transitions which causes udelay() to expire earlier than it should
sometimes. From Viresh Kumar.
- New trace points and rework of some existing trace points for
system suspend/resume profiling from Todd Brandt.
- Assorted cpufreq fixes and cleanups from Stratos Karafotis and
Viresh Kumar.
- Copyright notice update for suspend-and-cpuhotplug.txt from
Srivatsa S Bhat"
* tag 'pm+acpi-3.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / hotplug / PCI: Add hotplug contexts to PCI host bridges
PM / sleep: trace events for device PM callbacks
cpufreq: cpufreq-cpu0: remove dependency on THERMAL and REGULATOR
cpufreq: tegra: update comment for clarity
cpufreq: intel_pstate: Remove duplicate CPU ID check
cpufreq: Mark CPU0 driver with CPUFREQ_NEED_INITIAL_FREQ_CHECK flag
PM / Documentation: Update copyright in suspend-and-cpuhotplug.txt
cpufreq: governor: remove copy_prev_load from 'struct cpu_dbs_common_info'
cpufreq: governor: Be friendly towards latency-sensitive bursty workloads
PM / sleep: trace events for suspend/resume
cpufreq: ppc-corenet-cpu-freq: do_div use quotient
Revert "cpufreq: Enable big.LITTLE cpufreq driver on arm64"
cpufreq: Tegra: implement intermediate frequency callbacks
cpufreq: add support for intermediate (stable) frequencies
ACPI / video: Change the default for video.use_native_backlight to 1
ACPI: Fix bug when ACPI reset register is implemented in system memory
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED updates from Bryan Wu:
"I just found merge window is open and I'm quite busy and almost forget
to send out this pull request. Thanks Russell and Alexandre ping me
about this.
So basically we got some clean up and leds-pwm fixing patches from
Russell"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Remove duplicated OOM message for individual driver
drivers/leds: Replace __get_cpu_var use through this_cpu_ptr
leds: lp55xx: add DT bindings for LP55231
leds: 88pm860x: Fix missing refcount decrement for parent of_node
leds: 88pm860x: Use of_get_child_by_name
leds: leds-pwm: add DT support for LEDs wired to supply
leds: leds-pwm: implement PWM inversion
leds: leds-pwm: convert OF parsing code to use led_pwm_add()
leds: leds-pwm: provide a common function to setup a single led-pwm device
leds: pca9685: Remove leds-pca9685 driver
dell-led: add mic mute led interface
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight fixes from Lee Jones:
"This merely contains some very basic build/run-time bug fixes"
* tag 'backlight-for-linus-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: gpio-backlight: Fix warning when the GPIO is on a I2C chip
video/backlight: s6e63m0: Fix string type mismatch
video/backlight: LP8788 needs PWM
video/backlight: LP855X needs PWM
video/pxa: LCD_CORGI needs BACKLIGHT_CLASS_DEVICE
video/backlight: LM3630A needs PWM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull more MFD updates from Lee Jones:
"I missed collecting these patches due to a branch/tag naming
ambiguity. Completely my own fault, as I mindlessly named a branch
and tag identically. Sorry for the fuss.
This pull-request contains some misplaced patches from Tony Lindgren
that should have been part of the initial one"
* tag 'mfd-for-linus-3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle
mfd: twl4030-power: Add support for board specific configuration
mfd: twl4030-power: Add recommended idle configuration
mfd: twl4030-power: Add generic reset configuration
mfd: twl4030-power: Fix some defines for SW_EVENTS
mfd: twl4030-power: Fix hang on reboot if sleep configuration was loaded earlier
|
|
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes for 3.16.
- fix some various compiler warnings
- make atmel-mci compile again
- fix regression for sdhci-msm"
* tag 'mmc-v3.16-2' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: simplify SDHCI Kconfig dependencies
mmc: omap: don't select TPS65010
mmc: mvsdio: avoid compiler warning
mmc: atmel-mci: incude asm/cacheclush.h
mmc: sdhci-msm: Fix fallout from sdhci refactoring
mmc: usdhi6rol0: fix compiler warnings
|
|
Pull drm updates from Dave Airlie:
"This is the main drm merge window pull request, changes all over the
place, mostly normal levels of churn.
Highlights:
Core drm:
More cleanups, fix race on connector/encoder naming, docs updates,
object locking rework in prep for atomic modeset
i915:
mipi DSI support, valleyview power fixes, cursor size fixes,
execlist refactoring, vblank improvements, userptr support, OOM
handling improvements
radeon:
GPUVM tuning and large page size support, gart fixes, deep color
HDMI support, HDMI audio cleanups
nouveau:
- displayport rework should fix lots of issues
- initial gk20a support
- gk110b support
- gk208 fixes
exynos:
probe order fixes, HDMI changes, IPP consolidation
msm:
debugfs updates, misc fixes
ast:
ast2400 support, sync with UMS driver
tegra:
cleanups, hdmi + hw cursor for Tegra 124.
panel:
fixes existing panels add some new ones.
ipuv3:
moved from staging to drivers/gpu"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (761 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
|
|
When running RHEL6 userspace on a current upstream kernel, "ip link"
fails to show VF information.
The reason is a kernel<->userspace API change introduced by commit
88c5b5ce5cb57 ("rtnetlink: Call nlmsg_parse() with correct header length"),
after which the kernel does not see iproute2's IFLA_EXT_MASK attribute
in the netlink request.
iproute2 adjusted for the API change in its commit 63338dca4513
("libnetlink: Use ifinfomsg instead of rtgenmsg in rtnl_wilddump_req_filter").
The problem has been noticed before:
http://marc.info/?l=linux-netdev&m=136692296022182&w=2
(Subject: Re: getting VF link info seems to be broken in 3.9-rc8)
We can do better than tell those with old userspace to upgrade. We can
recognize the old iproute2 in the kernel by checking the netlink message
length. Even when including the IFLA_EXT_MASK attribute, its netlink
message is shorter than struct ifinfomsg.
With this patch "ip link" shows VF information in both old and new
iproute2 versions.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to a problem observed when losing a FIN segment that does not
contain data. In such situations, TLP is unable to recover from
*any* tail loss and instead adds at least PTO ms to the
retransmission process, i.e., RTO = RTO + PTO.
Signed-off-by: Per Hurtig <per.hurtig@kau.se>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fugang Duan says:
====================
net: fec: Enable Software TSO to improve the tx performance
Add SG and software TSO support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board, running iperf tcp tests shows:
* 82% improvement comparing with NO SG & TSO patch
$ ethtool -K eth0 sg on
$ ethtool -K eth0 tso on
[ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec
* cpu loading is 30%
$ ethtool -K eth0 sg off
$ ethtool -K eth0 tso off
[ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec
FEC HW support IP header and TCP/UDP hw checksum, support multi buffer descriptor transfer
one frame, but don't support HW TSO. And imx6q/dl SOC FEC Gbps speed has HW bus Bandwidth
limitation (400Mbps ~ 700Mbps), imx6sx SOC FEC Gbps speed has no HW bandwidth limitation.
The patch set just enable TSO feature, which is done following the mv643xx_eth driver.
Test result analyze:
imx6dl sabresd board: there have 82% improvement, since imx6dl FEC HW has bandwidth limitation,
the performance with SW TSO is a milestone.
Addition test:
imx6sx sdb board:
upstream still don't support imx6sx due to some patches being upstream... they use same FEC IP.
Use the SW TSO patches test imx6sx sdb board in internal kernel tree:
No SW TSO patch: tx bandwidth 840Mbps, cpu loading is 100%.
SW TSO patch: tx bandwidth 942Mbps, cpu loading is 65%.
It means the patch set have great improvement for imx6sx FEC performance.
V2:
* From Frank Li's suggestion:
Change the API "fec_enet_txdesc_entry_free" name to "fec_enet_get_free_txdesc_num".
* Summary David Laight and Eric Dumazet's thoughts:
RX BD entry number change to 256.
* From ezequiel's suggestion:
Follow the latest TSO fixes from his solution to rework the queue stop/wake-up.
Avoid unmapping the TSO header buffers.
* From Eric Dumazet's suggestion:
Avoid more bytes copy, just copying the unaligned part of the payload into first
descriptor. The suggestion will bring more complex for the driver, and imx6dl FEC
DMA need 16 bytes alignment, but cpu loading is not problem that cpu loading is
30%, the current performance is so better. Later chip like imx6sx Gigbit FEC DMA
support byte alignment, so there don't exist memory copy. So, the V2 version drop
the suggestion.
Anyway, thanks for Eric's response and suggestion.
V3:
* From David Laight's feedback:
Decide to drop RX BD entry number change for the SW TSO patch set.
I will generate one separate patch to increase RX BDs entry for interrupt coalescing feature which
will be supported in my later patch set.
V4:
* From David Laight's feedback:
Remove the conditional in .fec_enet_get_bd_index().
V5:
* Patch #4 update:
From David Laight's feedback:
"expect fec_enet_get_free_txdesc_num() to return one less than it does currently."
Change the function:
Return space available, 0..size-1. it always leave one free entry. Which is same as linux circ_buf.
Thanks for Eric and ezequiel's help and idea.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add software TSO support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board, running iperf tcp tests shows:
- 16.2% improvement comparing with FEC SG patch
- 82% improvement comparing with NO SG & TSO patch
$ ethtool -K eth0 tso on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec
During the testing, CPU loading is 30%.
Since imx6dl FEC Bandwidth is limited to SOC system bus bandwidth, the
performance with SW TSO is a milestone.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Scatter/gather support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board:
Running iperf tests shows a 55.4% improvement.
$ ethtool -K eth0 sg off
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec
$ ethtool -K eth0 sg on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52617 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 154 MBytes 432 Mbits/sec
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support SG, software TSO, let's increase BD entry number.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to enhance the code readable, let's factorize the
feature list.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IP header checksum is calcalated by network layer in default.
To support software TSO, it is better to use HW calculate the
IP header checksum.
FEC hw checksum feature request the checksum field in frame
is zero, otherwise the calculative CRC is not correct.
For segmentated TCP packet, HW calculate the IP header checksum again,
it doesn't bring any impact. For SW TSO, HW calculated checksum bring
better performance.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the code more readable and easy to support other features like
SG, TSO, moving the common transmit function to one api.
And the patch also factorize the getting BD index to it own function.
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some fields in "struct net_bridge" aren't available when compiling the
kernel without IPv6 support. Therefore adding a check/macro to skip the
complaining code sections in that case.
Introduced by 2cd4143192e8c60f66cb32c3a30c76d0470a372d
("bridge: memorize and export selected IGMP/MLD querier port")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"New smatch warnings:
net/bridge/br_multicast.c:1368 br_ip6_multicast_query() error:
we previously assumed 'group' could be null (see line 1349)"
In the rare (sort of broken) case of a query having a Maximum
Response Delay of zero, we could create a potential null pointer
dereference.
Fixing this by skipping the multicast specific MLD Query parsing again
if no multicast group address is available.
Introduced by dc4eb53a996a78bfb8ea07b47423ff5a3aadc362
("bridge: adhere to querier election mechanism specified by RFCs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With some specific configuration (VT6105M on Soekris 5510 and depending
on the device at the other end), fragmented packets were not transmitted
when forcing 100 full-duplex with autoneg disable.
This fix now write full-duplex chips register when forcing full or
half-duplex not only when autoneg is enable.
Signed-off-by: François Cachereul <f.cachereul@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"This the bunch that sat in -next + lock_parent() fix. This is the
minimal set; there's more pending stuff.
In particular, I really hope to get acct.c fixes merged this cycle -
we need that to deal sanely with delayed-mntput stuff. In the next
pile, hopefully - that series is fairly short and localized
(kernel/acct.c, fs/super.c and fs/namespace.c). In this pile: more
iov_iter work. Most of prereqs for ->splice_write with sane locking
order are there and Kent's dio rewrite would also fit nicely on top of
this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
lock_parent: don't step on stale ->d_parent of all-but-freed one
kill generic_file_splice_write()
ceph: switch to iter_file_splice_write()
shmem: switch to iter_file_splice_write()
nfs: switch to iter_splice_write_file()
fs/splice.c: remove unneeded exports
ocfs2: switch to iter_file_splice_write()
->splice_write() via ->write_iter()
bio_vec-backed iov_iter
optimize copy_page_{to,from}_iter()
bury generic_file_aio_{read,write}
lustre: get rid of messing with iovecs
ceph: switch to ->write_iter()
ceph_sync_direct_write: stop poking into iov_iter guts
ceph_sync_read: stop poking into iov_iter guts
new helper: copy_page_from_iter()
fuse: switch to ->write_iter()
btrfs: switch to ->write_iter()
ocfs2: switch to ->write_iter()
xfs: switch to ->write_iter()
...
|
|
Yuval Mintz says:
====================
bnx2x: Bug fixes patch series
This patch series contains various bug fixes - 2 link related fixes,
one sriov-related issue and an additional fix for a theoretical bug
on new boards.
Please consider applying these patches to `net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A malicious VF might try to starve the other VFs & PF by creating
contineous doorbell floods. In order to negate this, HW has a threshold of
doorbells per client, which will stop the client doorbells from arriving
if crossed.
The threshold currently configured for VFs is too low - under extreme traffic
scenarios, it's possible for a VF to reach the threshold and thus for its
fastpath to stop working.
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If L2FW utilized by the UNDI driver has the same version number as that
of the regular FW, a driver loading after UNDI and receiving an uncommon
answer from management will mistakenly assume the loaded FW matches its
own requirement and try to exist the flow via FLR.
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the phy access mode even in case of link-flap avoidance.
Signed-off-by: Yaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This avoids clearing the RX polarity setting in KR mode when polarity lane
is swapped, as otherwise this will result in failed link.
Signed-off-by: Yaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Consider the scenario:
For a TCP-style socket, while processing the COOKIE_ECHO chunk in
sctp_sf_do_5_1D_ce(), after it has passed a series of sanity check,
a new association would be created in sctp_unpack_cookie(), but afterwards,
some processing maybe failed, and sctp_association_free() will be called to
free the previously allocated association, in sctp_association_free(),
sk_ack_backlog value is decremented for this socket, since the initial
value for sk_ack_backlog is 0, after the decrement, it will be 65535,
a wrap-around problem happens, and if we want to establish new associations
afterward in the same socket, ABORT would be triggered since sctp deem the
accept queue as full.
Fix this issue by only decrementing sk_ack_backlog for associations in
the endpoint's list.
Fix-suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* pm-sleep:
PM / sleep: trace events for device PM callbacks
PM / sleep: trace events for suspend/resume
|
|
* pm-cpufreq:
cpufreq: cpufreq-cpu0: remove dependency on THERMAL and REGULATOR
cpufreq: tegra: update comment for clarity
cpufreq: intel_pstate: Remove duplicate CPU ID check
cpufreq: Mark CPU0 driver with CPUFREQ_NEED_INITIAL_FREQ_CHECK flag
cpufreq: governor: remove copy_prev_load from 'struct cpu_dbs_common_info'
cpufreq: governor: Be friendly towards latency-sensitive bursty workloads
cpufreq: ppc-corenet-cpu-freq: do_div use quotient
Revert "cpufreq: Enable big.LITTLE cpufreq driver on arm64"
cpufreq: Tegra: implement intermediate frequency callbacks
cpufreq: add support for intermediate (stable) frequencies
|
|
* acpi-general:
ACPI: Fix bug when ACPI reset register is implemented in system memory
* acpi-video:
ACPI / video: Change the default for video.use_native_backlight to 1
|
|
* acpi-hotplug:
ACPI / hotplug / PCI: Add hotplug contexts to PCI host bridges
|
|
We have a number of front-end drivers for SDHCI_PLTFM, some of them
use 'select MMC_SDHCI_PLTFM', others use 'depends on'. This is
inconsistent and confusing, and in one case has also led to a
build error because of incomplete dependencies:
warning: (MMC_SDHCI_PXAV3 && MMC_SDHCI_PXAV2 && MMC_SDHCI_BCM_KONA) selects MMC_SDHCI_PLTFM which has unmet direct dependencies (MMC && MMC_SDHCI)
drivers/built-in.o: In function `sdhci_sirf_resume':
:(.text+0xaaacb4): undefined reference to `sdhci_resume_host'
drivers/built-in.o: In function `sdhci_sirf_suspend':
:(.text+0xaaacf8): undefined reference to `sdhci_suspend_host'
drivers/built-in.o: In function `sdhci_sirf_probe':
:(.text+0xaaaf44): undefined reference to `sdhci_add_host'
:(.text+0xaaaf50): undefined reference to `sdhci_remove_host'
This changes Kconfig to use 'depends on MMC_SDHCI_PLTFM' for all these
cases, to fix the build error and make the logic more logical.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The MMC host driver should not select the pmic driver, since that
may have other dependencies, notably i2c in this case. It's not
clear what the exact requirement of the driver is, but to preserve
the behavior, this patch changes the 'select' into 'depends on',
meaning you now have to turn on TPS65010 explicitly and then
MMC_OMAP.
Found during randconfig build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
gcc correctly points out that hw_state can be used uninitially
in the mvsd_setup_data() function. This rearranges the function
to ensure it always contains a proper value.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Chris Ball <chris@printf.net>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: linux-mmc@vger.kernel.org
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This avoids a build error due to the use of flush_dcache_page.
drivers/mmc/host/atmel-mci.c: In function 'atmci_read_data_pio':
drivers/mmc/host/atmel-mci.c:1870:5: error: implicit declaration of function 'flush_dcache_page' [-Werror=implicit-function-declaration]
flush_dcache_page(sg_page(sg));
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sdhci core was refactored recently and some of those
refactorings required changes in every sdhci platform driver.
Those updates happened around the same time as when the msm
driver was merged so the refactorings missed the msm driver.
Hook in the basic library functions so that we can boot apq8074
dragonboards again instead of crashing when we try to jump to
NULL function pointers.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Georgi Djakov <gdjakov@mm-sol.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Georgi Djakov <gdjakov@mm-sol.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix a number of wrong print formats.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Dentry that had been through (or into) __dentry_kill() might be seen
by shrink_dentry_list(); that's normal, it'll be taken off the shrink
list and freed if __dentry_kill() has already finished. The problem
is, its ->d_parent might be pointing to already freed dentry, so
lock_parent() needs to be careful.
We need to check that dentry hasn't already gone into __dentry_kill()
*and* grab rcu_read_lock() before dropping ->d_lock - the latter makes
sure that whatever we see in ->d_parent after dropping ->d_lock it
won't be freed until we drop rcu_read_lock().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Backmerge of dcache.c changes from mainline. It's that, or complete
rebase...
Conflicts:
fs/splice.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
no callers left
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
ocfs2 was using a bunch of splice.c guts...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
iter_file_splice_write() - a ->splice_write() instance that gathers the
pipe buffers, builds a bio_vec-based iov_iter covering those and feeds
it to ->write_iter(). A bunch of simple cases coverted to that...
[AV: fixed the braino spotted by Cyrill]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
