1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
|
#!/usr/bin/make -f
# -*- makefile -*-
# Sample debian/rules that uses debhelper.
#
# This file was originally written by Joey Hess and Craig Small.
# As a special exception, when this file is copied by dh-make into a
# dh-make output file, you may use that output file without restriction.
# This special exception was added by Craig Small in version 0.37 of dh-make.
#
# Modified to make a template file for a multi-binary package with separated
# build-arch and build-indep targets by Bill Allombert 2001
# Official build number. Leave set to 0 if not an official build.
BUILD_NUMBER = 0
PACKAGE=openvswitch
pdkms=openvswitch-datapath-dkms
DEB_UPSTREAM_VERSION=$(shell dpkg-parsechangelog | sed -rne 's,^Version: ([0-9]:)*([^-]+).*,\2,p')
srcfiles := $(filter-out debian, $(wildcard * .[^.]*))
ifneq (,$(filter parallel=%,$(DEB_BUILD_OPTIONS)))
PARALLEL = -j$(patsubst parallel=%,%,$(filter parallel=%,$(DEB_BUILD_OPTIONS)))
else
PARALLEL =
endif
MAKEFLAGS += $(PARALLEL)
ifneq (,$(filter noopt,$(DEB_BUILD_OPTIONS)))
CFLAGS += -O0
else
CFLAGS += -O2
endif
configure: configure-stamp
configure-stamp:
dh_testdir
test -e configure || ./boot.sh
test -d _debian || mkdir _debian
echo $(DEB_BUILD_OPTIONS)
echo $$CC
cd _debian && ( \
test -e Makefile || \
../configure --prefix=/usr --localstatedir=/var --enable-ssl \
--sysconfdir=/etc --with-build-number=$(BUILD_NUMBER) \
CFLAGS="$(CFLAGS)" $(DATAPATH_CONFIGURE_OPTS))
touch configure-stamp
#Architecture
build: build-arch build-indep
build-arch: build-arch-stamp
build-arch-stamp: configure-stamp
$(MAKE) -C _debian
ifeq (,$(filter nocheck,$(DEB_BUILD_OPTIONS)))
if $(MAKE) -C _debian check TESTSUITEFLAGS='$(PARALLEL)'; then :; \
else \
cat _debian/tests/testsuite.log; \
exit 1; \
fi
endif
touch $@
build-indep: build-indep-stamp
build-indep-stamp: configure-stamp
$(MAKE) -C _debian dist distdir=openvswitch
touch $@
clean:
dh_testdir
dh_testroot
rm -f build-arch-stamp build-indep-stamp configure-stamp
rm -rf _debian
[ ! -f Makefile ] || $(MAKE) distclean
dh_clean
install: install-indep install-arch
install-indep: build-indep
dh_testdir
dh_testroot
dh_prep -i
dh_installdirs -i
$(MAKE) -C _debian DESTDIR=$(CURDIR)/debian/tmp install
dh_install -i
sed 's/^BUILD_NUMBER = .*/BUILD_NUMBER = $(BUILD_NUMBER)/' \
< debian/rules.modules \
> debian/openvswitch-datapath-source/usr/src/modules/openvswitch-datapath/debian/rules
chmod 755 debian/openvswitch-datapath-source/usr/src/modules/openvswitch-datapath/debian/rules
cd debian/openvswitch-datapath-source/usr/src && tar -c modules | bzip2 -9 > openvswitch-datapath.tar.bz2 && rm -rf modules
#dkms stuff
# setup the dirs
dh_installdirs -p$(pdkms) usr/src/$(PACKAGE)-$(DEB_UPSTREAM_VERSION)
# copy the source
cd debian/$(pdkms)/usr/src/$(PACKAGE)-$(DEB_UPSTREAM_VERSION) && tar xvzf $(CURDIR)/_debian/openvswitch.tar.gz && mv openvswitch/* . && rmdir openvswitch
# Prepare dkms.conf from the dkms.conf.in template
sed "s/__VERSION__/$(DEB_UPSTREAM_VERSION)/g" debian/dkms.conf.in > debian/$(pdkms)/usr/src/$(PACKAGE)-$(DEB_UPSTREAM_VERSION)/dkms.conf
install-arch: build-arch
dh_testdir
dh_testroot
dh_prep -s
dh_installdirs -s
$(MAKE) -C _debian DESTDIR=$(CURDIR)/debian/tmp install
cp debian/openvswitch-switch.template debian/openvswitch-switch/usr/share/openvswitch/switch/default.template
dh_install -s
# Must not depend on anything. This is to be called by
# binary-arch/binary-indep
# in another 'make' thread.
binary-common:
dh_testdir
dh_testroot
dh_installchangelogs
dh_installdocs
dh_installexamples
dh_installdebconf
dh_installlogrotate
dh_installinit -R -Nopenvswitch-switch
dh_installinit -R -popenvswitch-switch --error-handler=init_script_error
dh_installcron
dh_installman --language=C
dh_link
dh_strip --dbg-package=openvswitch-dbg
dh_compress
dh_fixperms
dh_python2
dh_perl
dh_makeshlibs
dh_installdeb
dh_shlibdeps
dh_gencontrol
dh_md5sums
dh_builddeb
binary-indep: install-indep
$(MAKE) -f debian/rules DH_OPTIONS=-i binary-common
binary-arch: install-arch
$(MAKE) -f debian/rules DH_OPTIONS=-s binary-common
binary: binary-arch binary-indep
.PHONY: build clean binary-indep binary-arch binary install install-indep install-arch configure
# This GNU make extensions disables parallel builds for the current Makefile
# but not for sub-Makefiles. This is appropriate here because build-arch and
# build-indep both invoke "make" on OVS, which can update some of the same
# targets in ways that conflict (e.g. both update tests/testsuite).
.NOTPARALLEL:
|
