| Age | Commit message (Collapse) | Author |
|---|
|
Linux 3.12-rc2
|
|
Merged in v3.12-rc1.
Fair number of conflicts & issues
* Managed to resolve most of the netfilter issues
* Had to drop some of the bluetooth sco changes
* Had to drop some cgroup changes
* Other fixups in ion and various shrinker updates
* The upstream EVIOCREVOKE uses the same ioctl number as
EVIOCSSUSPENDBLOCK, so I had to change EVIOCSSUSPENDBLOCK.
This may cause problems until userland is updated to use new
EVIOCSSUSPENDBLOCK ioctl number.
There's probably more issues not resolved, but its a decent first pass.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Conflicts:
arch/arm/mm/cache-l2x0.c
drivers/hid/hid-multitouch.c
drivers/input/evdev.c
drivers/mmc/core/core.c
drivers/power/power_supply_core.c
include/linux/cgroup.h
include/net/bluetooth/sco.h
include/net/tcp.h
kernel/sched/core.c
net/bluetooth/hci_conn.c
net/bluetooth/hci_event.c
net/bluetooth/sco.c
net/ipv4/netfilter/Kconfig
net/ipv6/netfilter/Kconfig
net/netfilter/xt_socket.c
|
|
Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).
Wait until firmware ack is written before unlocking channel
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.
This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When system CPU is stressed it's possible that the driver will not be able
to pulse the FW every second, which will cause the log to be filled with
error messages.
Increasing the threshold to 5 seconds seems to be enough to eliminate the
issue.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the
actual configuration. Change the 848xx duplex settings to advertise half-duplex
only if configured.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when 1G-optic module was plugged in, internal loopback test failed because the
driver used to check the optic module (with no need), and for 1G optic module,
the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled.
This patch avoid accessing optic module in case internal loopback was selected,
and update the link speed in case 1G optic module was detected during init
stage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not
configured in order to clear it's configuration, otherwise the link may come up
at 20G instead of the requested 10G-KR. In addition, restart AN after
disabling KR2 as part of the KR2 work-around.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, in case of KR link down, the driver would reset the PHY and restart
auto negotiation only when old Warpcore microcode was used (below D108).
This patch comes to generalize this by keep trying to restart KR link,
regardless of Warpcore microcode, since it was found that it solves another link
issue which source is a link-partner. As part of this change, the signal
detect is no longer a condition to apply the work-around to cover this new case.
Like before, as long as the link is down, AN will be restarted every 2 seconds.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ben Hutchings says:
====================
Daniel Pieczko fixed two bugs in reset handling that particularly
affected the new SFC9120 controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The old implementation was heavy on str* functions and sprintf calls.
This version is more manual, but faster.
Profiling just the printing of a 3 char CAN-id resulted in 60 instructions
for the manual method and over 2000 for the sprintf method. Bear in
mind the profiling was done against libc and not the kernel sprintf.
Together with this rewrite an issue with sending and receiving of RTR frames
has been fixed by Oliver for the cases that the DLC is not zero.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The locking is needed, since the the internal buffer for the CAN frames is
changed during the wakeup call. This could cause buffer inconsistencies
under high loads, especially for the outgoing short CAN packet skbuffs.
The needed locks led to deadlocks before commit
"5ede52538ee2b2202d9dff5b06c33bfde421e6e4 tty: Remove extra wakeup from pty
write() path", which removed the direct callback to the wakeup function from the
tty layer.
As slcan.c is based on slip.c the issue in the original code is fixed, too.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx and rx urbs are not deallocated if something goes wrong in peak_usb_start().
The patch fixes error handling to deallocate all the resources.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The SFC9120 MC firmware often takes longer than 20ms to reboot and
update the warm boot count in BIU_MC_SFT_STATUS_REG. A timeout of
250ms is very generous for an MC reboot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Scheduling a reset following an MC reboot event before waiting for
reboot to complete results in a race that can lead to a state where
must_realloc_vis is false in efx_ef10_fini_dmaq() but the VIs have
been destroyed during the MC reboot.
To avoid MC errors when trying to remove VIs that do not exist, wait
for the MC reboot to complete before scheduling the reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Pull networking fixes from David Miller:
1) If the local_df boolean is set on an SKB we have to allocate a
unique ID even if IP_DF is set in the ipv4 headers, from Ansis
Atteka.
2) Some fixups for the new chipset support that went into the sfc
driver, from Ben Hutchings.
3) Because SCTP bypasses a good chunk of, and actually duplicates, the
logic of the ipv6 output path, some IPSEC things don't get done
properly. Integrate SCTP better into the ipv6 output path so that
these problems are fixed and such issues don't get missed in the
future either. From Daniel Borkmann.
4) Fix skge regressions added by the DMA mapping error return checking
added in v3.10, from Mikulas Patocka.
5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.
6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.
7) Fix error handling in tun_set_iff(), in particular don't leak
resources. From Jason Wang.
8) Prevent format-string injection into xen-netback driver, from Kees
Cook.
9) Fix regression added to netpoll ARP packet handling, in particular
check for the right ETH_P_ARP protocol code. From Sonic Zhang.
10) Try to deal with AMD IOMMU errors when using r8169 chips, from
Francois Romieu.
11) Cure freezes due to recent changes in the rt2x00 wireless driver,
from Stanislaw Gruszka.
12) Don't do SPI transfers (which can sleep) in interrupt context in
cw1200 driver, from Solomon Peachy.
13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
From Nithin Sujir.
14) Make xen_netbk_count_skb_slots() count the actual number of slots
that will be used, taking into consideration packing and other
issues that the transmit path will run into. From David Vrabel.
15) Use the correct maximum age when calculating the bridge
message_age_timer, from Chris Healy.
16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
Khoroshilov.
17) Netfilter conntrack extensions were converted to RCU but are not
always freed properly using kfree_rcu(). Fix from Michal Kubecek.
18) VF reset recovery not being done correctly in qlcnic driver, from
Manish Chopra.
19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.
20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.
21) Internal switch not initialized properly in bgmac driver, from Rafał
Miłecki.
22) Netlink messages report wrong local and remote addresses in IPv6
tunneling, from Ding Zhi.
23) ICMP redirects should not generate socket errors in DCCP and SCTP.
We're still working out how this should be handled for RAW and UDP
sockets. From Daniel Borkmann and Duan Jiong.
24) We've had several bugs wherein the network namespace's loopback
device gets accessed after it is free'd, NULL it out so that we can
catch these problems more readily. From Eric W Biederman.
25) Fix regression in TCP RTO calculations, from Neal Cardwell.
26) Fix too early free of xen-netback network device when VIFs still
exist. From Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
netconsole: fix a deadlock with rtnl and netconsole's mutex
netpoll: fix NULL pointer dereference in netpoll_cleanup
skge: fix broken driver
ip: generate unique IP identificator if local fragmentation is allowed
ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
xen-netback: Don't destroy the netdev until the vif is shut down
net:dccp: do not report ICMP redirects to user space
cnic: Fix crash in cnic_bnx2x_service_kcq()
bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
vxlan: Avoid creating fdb entry with NULL destination
tcp: fix RTO calculated from cached RTT
drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
net loopback: Set loopback_dev to NULL when freed
batman-adv: set the TAG flag for the vid passed to BLA
netfilter: nfnetlink_queue: use network skb for sequence adjustment
net: sctp: rfc4443: do not report ICMP redirects to user space
net: usb: cdc_ether: use usb.h macros whenever possible
net: usb: cdc_ether: fix checkpatch errors and warnings
net: usb: cdc_ether: Use wwan interface for Telit modules
ip6_tunnels: raddr and laddr are inverted in nl msg
...
|
|
This bug was introduced by commit
7a163bfb7ce50895bbe67300ea610d31b9c09230 ("netconsole: avoid a crash with
multiple sysfs writers"). In store_enabled() we have the following
sequence: acquire nt->mutex then rtnl, but in the netconsole netdev
notifier we have rtnl then nt->mutex effectively leading to a deadlock.
The NULL pointer dereference that the above commit tries to fix is
actually due to another bug in netpoll_cleanup(). This is fixed by dropping
the mutex from the netdev notifier as it's already protected by rtnl.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch 136d8f377e1575463b47840bc5f1b22d94bf8f63 broke the skge driver.
Note this part of the patch:
+ if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+ dev_kfree_skb(nskb);
+ goto resubmit;
+ }
+
pci_unmap_single(skge->hw->pdev,
dma_unmap_addr(e, mapaddr),
dma_unmap_len(e, maplen),
PCI_DMA_FROMDEVICE);
skb = e->skb;
prefetch(skb->data);
- skge_rx_setup(skge, e, nskb, skge->rx_buf_size);
The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.
This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Vasiliy Glazov <vascom2@gmail.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.
For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.
With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 104a43edb264321a4d41850e98153b4fa8a9ef42
cnic: Use CHIP_NUM macros from bnx2x.h
changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not. There is another place in cnic that is still using
the old method to determine if FCoE is supported or not. The 2 methods
may not yield the same result after the network interface is brought down
and up. This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.
The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro. As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit b9871bcfd211d316adee317608dab44c58d6ea2d
bnx2x: VF RSS support - PF side
changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc. For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit afbd8bae9c798c5cdbe4439d3a50536b5438247c
vxlan: add implicit fdb entry for default destination
creates an implicit fdb entry for default destination. This results
in an invalid fdb entry if default destination is not specified.
For ex:
ip link add vxlan1 type vxlan id 100
creates the following fdb entry
00:00:00:00:00:00 dev vxlan1 dst 0.0.0.0 self permanent
This patch fixes this issue by creating an fdb entry only if a
valid default destination is specified.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
instead of <asm/io.h>
clears following warnings :
WARNING: Use include <linux/io.h> instead of <asm/io.h>
WARNING: Use include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has recently turned up that we have a number of long standing bugs
in the network stack cleanup code with use of the loopback device
after it has been freed that have not turned up because in most cases
the storage allocated to the loopback device is not reused, when those
accesses happen.
Set looback_dev to NULL to trigger oopses instead of silent data corrupt
when we hit this class of bug.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ben Hutchings says:
====================
Some bug fixes and future-proofing for the recently added SFC9120
support:
1. Minimal support for the 40G configuration.
2. Disable the incomplete PTP/hardware timestamping support.
3. Reset MAC stats properly after a firmware upgrade.
4. Re-check the datapath firmware capabilities after the controller is
reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use USB_DEVICE_AND_INTERFACE_INFO and USB_VENDOR_AND_INTERFACE_INFO
macros to reduce boilerplate.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: <stable@vger.kernel.org> # 3.0+ as far back as it applies cleanly
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. The max expected
value is 0xF, so now it should be possible to read decimal form ("15")
and hex form ("0xF").
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use separate table for alias entries in the ehea module, otherwise the
probe() function will operate on the separate ports instead of the
lhea-"root" entry of the device-tree
Addresses https://bugzilla.novell.com/show_bug.cgi?id=435215
[ Thadeu notes that: "... this issue might happen with the generation of
initrd, when the scripts check for /sys/class/net/eth0/device/modalias,
which links to the port device at
/sys/devices/ibmebus/23c00400.lhea/port0/" ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Olaf Hering <ohering@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When driver registration fails, we need to clean up the resources allocated
before. cxgb4 missed to destroy the workqueue allocated at the very beginning.
This patch destroies the workqueue when registration fails.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
running bonding in ALB mode requires that learning packets be sent periodically,
so that the switch knows where to send responding traffic. However, depending
on switch configuration, there may not be any need to send traffic at the
default rate of 3 packets per second, which represents little more than wasted
data. Allow the ALB learning packet interval to be made configurable via sysfs
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Acked-by: Veaceslav Falico <vfalico@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes sparse warnings when incorrectly handling the port number
and using int instead of unsigned int iterating through &vn->sock_list[].
Keeping the port as __be16 also makes things clearer wrt endianess.
Also, it was pointed out that vxlan_get_rx_port() had unnecessary checks
which got removed.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o At the time of firmware hang "adapter->need_fw_reset" variable gets
set but after re-initialization of firmware OR at the time of VF
re-initialization that variable was not getting cleared which
was leading to failure in VF reset recovery.Fix it by clearing
this variable before re-initializing VF
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/toshiba/ps3_gelic_net.c
It's a NOOP since 2.6.35 and I will remove it one day ;)
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch proposes to remove the IRQF_DISABLED flag from
code in drivers/net/ethernet/smsc/
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/pasemi/pasemi_mac.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch proposes to remove the IRQF_DISABLED flag from
code in drivers/net/ethernet/natsemi/
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/micrel/ks8851_mll.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/lantiq_etop.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/hp/hp100.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/freescale/fec_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
