diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/qrb5165-rb5.dts')
-rw-r--r-- | arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 764 |
1 files changed, 758 insertions, 6 deletions
diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index ce22d4fa383e..70ba1f6806fd 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -7,6 +7,8 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/sound/qcom,q6afe.h> +#include <dt-bindings/sound/qcom,q6asm.h> #include "sm8250.dtsi" #include "pm8150.dtsi" #include "pm8150b.dtsi" @@ -17,6 +19,7 @@ compatible = "qcom,qrb5165-rb5", "qcom,sm8250"; aliases { + hsuart0 = &uart6; serial0 = &uart12; sdhc2 = &sdhc_2; }; @@ -40,6 +43,17 @@ regulator-always-on; }; + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <<9611_out>; + }; + }; + }; + leds { compatible = "gpio-leds"; @@ -66,6 +80,108 @@ }; + lt9611_1v2: lt9611-vdd12-regulator { + compatible = "regulator-fixed"; + regulator-name = "LT9611_1V2"; + + vin-supply = <&vdc_3v3>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + + /* not connected on the board + gpio = <&pm8150l_gpios 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + */ + regulator-boot-on; + regulator-always-on; + }; + + lt9611_3v3: lt9611-3v3 { + compatible = "regulator-fixed"; + regulator-name = "LT9611_3V3"; + + vin-supply = <&vdc_3v3>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + + // TODO: make it possible to drive same GPIO from two clients + // gpio = <&pm8150l_gpios 7 GPIO_ACTIVE_HIGH>; + // enable-active-high; + }; + + thermal-zones { + xo-therm { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 0>; + trips { + active-config0 { + temperature = <50000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + wifi-therm { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 1>; + trips { + active-config0 { + temperature = <52000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + conn-therm { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150b_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + skin-msm-therm { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 0>; + + trips { + active-config0 { + temperature = <50000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + pm8150l-therm { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 1>; + + trips { + active-config0 { + temperature = <50000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + }; + vbat: vbat-regulator { compatible = "regulator-fixed"; regulator-name = "VBAT"; @@ -87,7 +203,7 @@ vdc_3v3: vdc-3v3-regulator { compatible = "regulator-fixed"; regulator-name = "VDC_3V3"; - vin-supply = <&dc12v>; + vin-supply = <&vreg_l11c_3p3>; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; @@ -118,6 +234,30 @@ regulator-max-microvolt = <1800000>; regulator-always-on; }; + + clk40M: can_clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <40000000>; + }; + + qca639x: qca639x { + compatible = "qcom,qca639x"; + #power-domain-cells = <0>; + + vddaon-supply = <&vreg_s6a_0p95>; + vddpmu-supply = <&vreg_s2f_0p95>; + vddrfa1-supply = <&vreg_s2f_0p95>; + vddrfa2-supply = <&vreg_s8c_1p3>; + vddrfa3-supply = <&vreg_s5a_1p9>; + vddpcie1-supply = <&vreg_s8c_1p3>; + vddpcie2-supply = <&vreg_s5a_1p9>; + vddio-supply = <&vreg_s4a_1p8>; + pinctrl-names = "default", "active"; + pinctrl-0 = <&wlan_default_state &bt_default_state>; + pinctrl-1 = <&wlan_active_state &bt_active_state>; + }; + }; &apps_rsc { @@ -131,6 +271,13 @@ vdd-l5-l6-supply = <&vreg_bob>; vdd-l7-supply = <&vreg_s4a_1p8>; + vreg_s2f_0p95: smps2 { + regulator-name = "vreg_s2f_0p95"; + regulator-min-microvolt = <512000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + vreg_l1f_1p1: ldo1 { regulator-name = "vreg_l1f_1p1"; regulator-min-microvolt = <1104000>; @@ -406,6 +553,187 @@ }; }; +&adsp { + status = "okay"; + firmware-name = "qcom/sm8250/adsp.mbn"; +}; + +&q6afedai { + qi2s@16 { + reg = <16>; + qcom,sd-lines = <0 1 2 3>; + }; +}; + +/* TERT I2S Uses 1 I2S SD Lines for audio on LT9611 HDMI Bridge */ +&q6afedai { + qi2s@20 { + reg = <20>; + qcom,sd-lines = <0>; + }; +}; + +&q6asmdai { + dai@0 { + reg = <0>; + }; + + dai@1 { + reg = <1>; + }; + + dai@2 { + reg = <2>; + }; +}; + +&swr0 { + + left_spkr: wsa8810-left{ + compatible = "sdw10217211000"; + reg = <0 3>; + powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrLeft"; + #sound-dai-cells = <0>; + }; + + + right_spkr: wsa8810-right{ + compatible = "sdw10217211000"; + reg = <0 4>; + powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrRight"; + #sound-dai-cells = <0>; + }; +}; + +&vamacro { + pinctrl-0 = <&cdc_dmic01_clk_active &cdc_dmic01_data_active>; + pinctrl-names = "default"; + vdd-micb-supply = <&vreg_s4a_1p8>; +}; + +&sound { + compatible = "qcom,qrb5165-rb5-sndcard"; + pinctrl-0 = <&tert_mi2s_sck_active + &tert_mi2s_sd0_active + &tert_mi2s_ws_active>; + pinctrl-names = "default"; + model = "Qualcomm-RB5-WSA8815-Speakers-DMIC0"; + audio-routing = + "SpkrLeft IN", "WSA_SPK1 OUT", + "SpkrRight IN", "WSA_SPK2 OUT", + "VA DMIC0", "vdd-micb", + "VA DMIC1", "vdd-micb", + "MM_DL1", "MultiMedia1 Playback", + "MM_DL2", "MultiMedia2 Playback", + "MultiMedia3 Capture", "MM_UL3"; + + mm1-dai-link { + link-name = "MultiMedia1"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; + }; + }; + + mm2-dai-link { + link-name = "MultiMedia2"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; + }; + }; + + mm3-dai-link { + link-name = "MultiMedia3"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; + }; + }; + + hdmi-dai-link { + link-name = "HDMI Playback"; + cpu { + sound-dai = <&q6afedai TERTIARY_MI2S_RX>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <<9611_codec 0>; + }; + }; + + dma-dai-link { + link-name = "WSA Playback"; + cpu { + sound-dai = <&q6afedai WSA_CODEC_DMA_RX_0>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro>; + }; + }; + + va-dai-link { + link-name = "VA Capture"; + cpu { + sound-dai = <&q6afedai VA_CODEC_DMA_TX_0>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <&vamacro 0>; + }; + }; +}; + +&cdsp { + status = "okay"; + firmware-name = "qcom/sm8250/cdsp.mbn"; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vreg_l9a_1p2>; + +#if 0 + qcom,dual-dsi-mode; + qcom,master-dsi; +#endif + + ports { + port@1 { + endpoint { + remote-endpoint = <<9611_a>; + data-lanes = <0 1 2 3>; + }; + }; + }; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vreg_l5a_0p88>; +}; + +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sm8250/a650_zap.mbn"; + }; +}; + /* LS-I2C0 */ &i2c4 { status = "okay"; @@ -413,6 +741,55 @@ &i2c5 { status = "okay"; + clock-frequency = <400000>; + + lt9611_codec: hdmi-bridge@2b { + compatible = "lontium,lt9611uxc"; + reg = <0x2b>; + #sound-dai-cells = <1>; + + interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>; + + reset-gpios = <&pm8150l_gpios 5 GPIO_ACTIVE_HIGH>; + + vdd-supply = <<9611_1v2>; + vcc-supply = <<9611_3v3>; + + pinctrl-names = "default"; + pinctrl-0 = <<9611_irq_pin <9611_rst_pin>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lt9611_a: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + +#if 0 + port@1 { + reg = <1>; + + lt9611_b: endpoint { + remote-endpoint = <&dsi1_out>; + }; + }; +#endif + + port@2 { + reg = <2>; + + lt9611_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + + }; + }; }; /* LS-I2C1 */ @@ -420,6 +797,150 @@ status = "okay"; }; +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 79 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_default_state>; +}; + +&pcie0_phy { + status = "okay"; + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; + + /* Power on QCA639x chip, otherwise PCIe bus timeouts */ + power-domains = <&qca639x>; +}; + +&pcie1 { + status = "okay"; + perst-gpio = <&tlmm 82 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie1_default_state>; +}; + +&pcie1_phy { + status = "okay"; + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; +}; + +&pcie2 { + status = "okay"; + perst-gpio = <&tlmm 85 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie2_default_state>; +}; + +&pcie2_phy { + status = "okay"; + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; +}; + +&pm8150_adc { + xo-therm@4c { + reg = <ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + wifi-therm@4e { + reg = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150b_adc { + conn-therm@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150l_adc { + skin-msm-therm@4e { + reg = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + pm8150l-therm@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150_adc_tm { + status = "okay"; + io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>, + <&pm8150_adc ADC5_AMUX_THM2_100K_PU>; + io-channel-names = "xo-therm", "wifi-therm"; + + xo-therm@0 { + reg = <0>; + qcom,adc-channel = <ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + wifi-therm@1 { + reg = <1>; + qcom,adc-channel = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150b_adc_tm { + status = "okay"; + io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>; + io-channel-names = "conn-therm"; + + conn-therm@0 { + reg = <0>; + qcom,adc-channel = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150l_adc_tm { + status = "okay"; + io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>, + <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>; + io-channel-names = "skin-msm-therm", "pm8150l-therm"; + + skin-msm-therm@0 { + reg = <0>; + qcom,adc-channel = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + pm8150l-therm@1 { + reg = <1>; + qcom,adc-channel = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + &pm8150_gpios { gpio-reserved-ranges = <1 1>, <3 2>, <7 1>; gpio-line-names = @@ -451,6 +972,35 @@ "NC"; }; +&pm8150b_typec { + status = "okay"; + connector { + compatible = "usb-c-connector"; + power-role = "dual"; + data-role = "dual"; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@1 { + reg = <1>; + usb3_data_ss: endpoint@0 { + remote-endpoint = <&qmp_ss_mux>; + }; + }; + }; + }; + + port { + usb3_role: endpoint { + remote-endpoint = <&dwc3_drd_switch>; + }; + }; +}; + +&pm8150b_vbus { + status = "okay"; +}; + &pm8150l_gpios { gpio-line-names = "NC", @@ -465,12 +1015,64 @@ "PM_GPIO-B", "NC", "PM3003A_MODE"; + + lt9611_rst_pin: lt9611-rst-pin { + pins = "gpio5"; + function = "normal"; + + output-high; + input-disable; + power-source = <0>; + }; +}; + +&pm8150l_lpg { + status = "okay"; + + led@1 { + reg = <1>; + label = "green:user0"; + + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + + led@2 { + reg = <2>; + label = "green:user1"; + default-state = "on"; + }; + + led@3 { + reg = <3>; + label = "green:user2"; + }; }; &pm8150_rtc { status = "okay"; }; +&qup_uart6_default { + ctsrx { + pins = "gpio16", "gpio19"; + drive-strength = <2>; + bias-disable; + }; + + rts { + pins = "gpio17"; + drive-strength = <2>; + bias-disable; + }; + + tx { + pins = "gpio18"; + drive-strength = <2>; + bias-pull-up; + }; +}; + &qupv3_id_0 { status = "okay"; }; @@ -491,12 +1093,15 @@ vqmmc-supply = <&vreg_l6c_2p96>; cd-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>; bus-width = <4>; - /* there seem to be issues with HS400-1.8V mode, so disable it */ - no-1-8-v; no-sdio; no-emmc; }; +&slpi { + /* status = "okay"; */ + firmware-name = "qcom/sm8250/slpi.mbn"; +}; + /* CAN */ &spi0 { status = "okay"; @@ -696,6 +1301,109 @@ "HST_WLAN_UART_TX", "HST_WLAN_UART_RX"; + bt_default_state: bt-default-state { + bt-en { + pins = "gpio21"; + function = "gpio"; + + drive-strength = <16>; + output-low; + bias-pull-up; + }; + }; + + bt_active_state: bt-active-state { + bt-en { + pins = "gpio21"; + function = "gpio"; + + drive-strength = <16>; + output-high; + bias-pull-up; + }; + }; + + lt9611_irq_pin: lt9611-irq { + pins = "gpio63"; + function = "gpio"; + bias-disable; + }; + + pcie0_default_state: pcie0-default { + clkreq { + pins = "gpio80"; + function = "pci_e0"; + bias-pull-up; + }; + + reset-n { + pins = "gpio79"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n { + pins = "gpio81"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie1_default_state: pcie1-default { + clkreq { + pins = "gpio83"; + function = "pci_e1"; + bias-pull-up; + }; + + reset-n { + pins = "gpio82"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n { + pins = "gpio84"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie2_default_state: pcie2-default { + clkreq { + pins = "gpio86"; + function = "pci_e2"; + bias-pull-up; + }; + + reset-n { + pins = "gpio85"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n { + pins = "gpio87"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + sdc2_default_state: sdc2-default { clk { pins = "sdc2_clk"; @@ -706,13 +1414,13 @@ cmd { pins = "sdc2_cmd"; bias-pull-up; - drive-strength = <16>; + drive-strength = <10>; }; data { pins = "sdc2_data"; bias-pull-up; - drive-strength = <16>; + drive-strength = <10>; }; }; @@ -721,6 +1429,37 @@ function = "gpio"; bias-pull-up; }; + + wlan_default_state: wlan-default-state { + wlan-en { + pins = "gpio20"; + function = "gpio"; + + drive-strength = <16>; + output-low; + bias-pull-up; + }; + }; + + wlan_active_state: wlan-active-state { + wlan-en { + pins = "gpio20"; + function = "gpio"; + + drive-strength = <16>; + output-high; + bias-pull-up; + }; + }; + +}; + +&uart6 { + status = "okay"; + bluetooth { + compatible = "qcom,qca6390-bt"; + power-domains = <&qca639x>; + }; }; &uart12 { @@ -749,10 +1488,17 @@ &usb_1 { status = "okay"; + usb-role-switch; + port { + dwc3_drd_switch: endpoint@0 { + remote-endpoint = <&usb3_role>; + }; + }; }; &usb_1_dwc3 { - dr_mode = "peripheral"; + dr_mode = "otg"; + usb-role-switch; }; &usb_1_hsphy { @@ -768,6 +1514,12 @@ vdda-phy-supply = <&vreg_l9a_1p2>; vdda-pll-supply = <&vreg_l18a_0p92>; + orientation-switch; + port { + qmp_ss_mux: endpoint@0 { + remote-endpoint = <&usb3_data_ss>; + }; + }; }; &usb_2 { |