Merge tag 'tty-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial driver fixes from Greg KH:
 "Here are a small number of tty/serial driver fixes to resolve reported
  issues with 3.14-rc and earlier (in the case of the vt bugfix).  Some
  of these have been tested and reported by a number of people as the
  tty bugfix was pretty commonly hit on some platforms.

  All have been in linux-next for a while"

* tag 'tty-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  vt: Fix secure clear screen
  serial: 8250: Support XR17V35x fraction divisor
  n_tty: Fix stale echo output
  serial: sirf: fix kernel panic caused by unpaired spinlock
  serial: 8250_pci: unbreak last serial ports on NetMos 9865 cards
  n_tty: Fix poll() when TIME_CHAR and MIN_CHAR == 0
  serial: omap: fix rs485 probe on defered pinctrl
  serial: 8250_dw: fix compilation warning when !CONFIG_PM_SLEEP
  serial: omap-serial: Move info message to probe function
  tty: Set correct tty name in 'active' sysfs attribute
  tty: n_gsm: Fix for modems with brk in modem status control
  drivers/tty/hvc: don't use module_init in non-modular hyp. console code

5 files changed, 32 insertions, 8 deletions

diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index 61ecd709a72..69932b7556c 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -2433,6 +2433,24 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
 	serial_dl_write(up, quot);
 
 	/*
+	 * XR17V35x UARTs have an extra fractional divisor register (DLD)
+	 *
+	 * We need to recalculate all of the registers, because DLM and DLL
+	 * are already rounded to a whole integer.
+	 *
+	 * When recalculating we use a 32x clock instead of a 16x clock to
+	 * allow 1-bit for rounding in the fractional part.
+	 */
+	if (up->port.type == PORT_XR17V35X) {
+		unsigned int baud_x32 = (port->uartclk * 2) / baud;
+		u16 quot = baud_x32 / 32;
+		u8 quot_frac = DIV_ROUND_CLOSEST(baud_x32 % 32, 2);
+
+		serial_dl_write(up, quot);
+		serial_port_out(port, 0x2, quot_frac & 0xf);
+	}
+
+	/*
 	 * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
 	 * is written without DLAB set, this mode will be disabled.
 	 */
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index faa64e64610..ed311357674 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -391,7 +391,7 @@ static int dw8250_remove(struct platform_device *pdev)
 	return 0;
 }
 
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
 static int dw8250_suspend(struct device *dev)
 {
 	struct dw8250_data *data = dev_get_drvdata(dev);
@@ -409,7 +409,7 @@ static int dw8250_resume(struct device *dev)
 
 	return 0;
 }
-#endif /* CONFIG_PM */
+#endif /* CONFIG_PM_SLEEP */
 
 #ifdef CONFIG_PM_RUNTIME
 static int dw8250_runtime_suspend(struct device *dev)
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 50228eed3b6..0ff3e3624d4 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -783,7 +783,8 @@ static int pci_netmos_9900_setup(struct serial_private *priv,
 {
 	unsigned int bar;
 
-	if ((priv->dev->subsystem_device & 0xff00) == 0x3000) {
+	if ((priv->dev->device != PCI_DEVICE_ID_NETMOS_9865) &&
+	    (priv->dev->subsystem_device & 0xff00) == 0x3000) {
 		/* netmos apparently orders BARs by datasheet layout, so serial
 		 * ports get BARs 0 and 3 (or 1 and 4 for memmapped)
 		 */
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index fa511ebab67..77f035158d6 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -738,9 +738,6 @@ static int serial_omap_startup(struct uart_port *port)
 			return retval;
 		}
 		disable_irq(up->wakeirq);
-	} else {
-		dev_info(up->port.dev, "no wakeirq for uart%d\n",
-			 up->port.line);
 	}
 
 	dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->port.line);
@@ -1604,8 +1601,11 @@ static int serial_omap_probe_rs485(struct uart_omap_port *up,
 					    flags & SER_RS485_RTS_AFTER_SEND);
 		if (ret < 0)
 			return ret;
-	} else
+	} else if (up->rts_gpio == -EPROBE_DEFER) {
+		return -EPROBE_DEFER;
+	} else {
 		up->rts_gpio = -EINVAL;
+	}
 
 	if (of_property_read_u32_array(np, "rs485-rts-delay",
 				    rs485_delay, 2) == 0) {
@@ -1687,6 +1687,9 @@ static int serial_omap_probe(struct platform_device *pdev)
 	up->port.iotype = UPIO_MEM;
 	up->port.irq = uartirq;
 	up->wakeirq = wakeirq;
+	if (!up->wakeirq)
+		dev_info(up->port.dev, "no wakeirq for uart%d\n",
+			 up->port.line);
 
 	up->port.regshift = 2;
 	up->port.fifosize = 64;
diff --git a/drivers/tty/serial/sirfsoc_uart.c b/drivers/tty/serial/sirfsoc_uart.c
index 49a2ffd101a..b7bfe24d4eb 100644
--- a/drivers/tty/serial/sirfsoc_uart.c
+++ b/drivers/tty/serial/sirfsoc_uart.c
@@ -542,8 +542,10 @@ static void sirfsoc_rx_tmo_process_tl(unsigned long param)
 	wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl,
 			rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) |
 			SIRFUART_IO_MODE);
-	sirfsoc_uart_pio_rx_chars(port, 4 - sirfport->rx_io_count);
 	spin_unlock_irqrestore(&sirfport->rx_lock, flags);
+	spin_lock(&port->lock);
+	sirfsoc_uart_pio_rx_chars(port, 4 - sirfport->rx_io_count);
+	spin_unlock(&port->lock);
 	if (sirfport->rx_io_count == 4) {
 		spin_lock_irqsave(&sirfport->rx_lock, flags);
 		sirfport->rx_io_count = 0;