aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2015-10-27asix: Do full reset during ax88772_bindCharles Keepax
[ Upstream commit 436c2a5036b6ffe813310df2cf327d3b69be0734 ] commit 3cc81d85ee01 ("asix: Don't reset PHY on if_up for ASIX 88772") causes the ethernet on Arndale to no longer function. This appears to be because the Arndale ethernet requires a full reset before it will function correctly, however simply reverting the above patch causes problems with ethtool settings getting reset. It seems the problem is that the ethernet is not properly reset during bind, and indeed the code in ax88772_bind that resets the device is a very small subset of the actual ax88772_reset function. This patch uses ax88772_reset in place of the existing reset code in ax88772_bind which removes some code duplication and fixes the ethernet on Arndale. It is still possible that the original patch causes some issues with suspend and resume but that seems like a separate issue and I haven't had a chance to test that yet. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Tested-by: Riku Voipio <riku.voipio@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-27asix: Don't reset PHY on if_up for ASIX 88772Michel Stam
[ Upstream commit 3cc81d85ee01e5a0b7ea2f4190e2ed1165f53c31 ] I've noticed every time the interface is set to 'up,', the kernel reports that the link speed is set to 100 Mbps/Full Duplex, even when ethtool is used to set autonegotiation to 'off', half duplex, 10 Mbps. It can be tested by: ifconfig eth0 down ethtool -s eth0 autoneg off speed 10 duplex half ifconfig eth0 up Then checking 'dmesg' for the link speed. Signed-off-by: Michel Stam <m.stam@fugro.nl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-27ppp: don't override sk->sk_state in pppoe_flush_dev()Guillaume Nault
[ Upstream commit e6740165b8f7f06d8caee0fceab3fb9d790a6fed ] Since commit 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release"), pppoe_release() calls dev_put(po->pppoe_dev) if sk is in the PPPOX_ZOMBIE state. But pppoe_flush_dev() can set sk->sk_state to PPPOX_ZOMBIE _and_ reset po->pppoe_dev to NULL. This leads to the following oops: [ 570.140800] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e0 [ 570.142931] IP: [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] PGD 3d119067 PUD 3dbc1067 PMD 0 [ 570.144601] Oops: 0000 [#1] SMP [ 570.144601] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppoe pppox ppp_generic slhc loop crc32c_intel ghash_clmulni_intel jitterentropy_rng sha256_generic hmac drbg ansi_cprng aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper acpi_cpufreq evdev serio_raw processor button ext4 crc16 mbcache jbd2 virtio_net virtio_blk virtio_pci virtio_ring virtio [ 570.144601] CPU: 1 PID: 15738 Comm: ppp-apitest Not tainted 4.2.0 #1 [ 570.144601] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014 [ 570.144601] task: ffff88003d30d600 ti: ffff880036b60000 task.ti: ffff880036b60000 [ 570.144601] RIP: 0010:[<ffffffffa018c701>] [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP: 0018:ffff880036b63e08 EFLAGS: 00010202 [ 570.144601] RAX: 0000000000000000 RBX: ffff880034340000 RCX: 0000000000000206 [ 570.144601] RDX: 0000000000000006 RSI: ffff88003d30dd20 RDI: ffff88003d30dd20 [ 570.144601] RBP: ffff880036b63e28 R08: 0000000000000001 R09: 0000000000000000 [ 570.144601] R10: 00007ffee9b50420 R11: ffff880034340078 R12: ffff8800387ec780 [ 570.144601] R13: ffff8800387ec7b0 R14: ffff88003e222aa0 R15: ffff8800387ec7b0 [ 570.144601] FS: 00007f5672f48700(0000) GS:ffff88003fc80000(0000) knlGS:0000000000000000 [ 570.144601] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 570.144601] CR2: 00000000000004e0 CR3: 0000000037f7e000 CR4: 00000000000406a0 [ 570.144601] Stack: [ 570.144601] ffffffffa018f240 ffff8800387ec780 ffffffffa018f240 ffff8800387ec7b0 [ 570.144601] ffff880036b63e48 ffffffff812caabe ffff880039e4e000 0000000000000008 [ 570.144601] ffff880036b63e58 ffffffff812cabad ffff880036b63ea8 ffffffff811347f5 [ 570.144601] Call Trace: [ 570.144601] [<ffffffff812caabe>] sock_release+0x1a/0x75 [ 570.144601] [<ffffffff812cabad>] sock_close+0xd/0x11 [ 570.144601] [<ffffffff811347f5>] __fput+0xff/0x1a5 [ 570.144601] [<ffffffff811348cb>] ____fput+0x9/0xb [ 570.144601] [<ffffffff81056682>] task_work_run+0x66/0x90 [ 570.144601] [<ffffffff8100189e>] prepare_exit_to_usermode+0x8c/0xa7 [ 570.144601] [<ffffffff81001a26>] syscall_return_slowpath+0x16d/0x19b [ 570.144601] [<ffffffff813babb1>] int_ret_from_sys_call+0x25/0x9f [ 570.144601] Code: 48 8b 83 c8 01 00 00 a8 01 74 12 48 89 df e8 8b 27 14 e1 b8 f7 ff ff ff e9 b7 00 00 00 8a 43 12 a8 0b 74 1c 48 8b 83 a8 04 00 00 <48> 8b 80 e0 04 00 00 65 ff 08 48 c7 83 a8 04 00 00 00 00 00 00 [ 570.144601] RIP [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP <ffff880036b63e08> [ 570.144601] CR2: 00000000000004e0 [ 570.200518] ---[ end trace 46956baf17349563 ]--- pppoe_flush_dev() has no reason to override sk->sk_state with PPPOX_ZOMBIE. pppox_unbind_sock() already sets sk->sk_state to PPPOX_DEAD, which is the correct state given that sk is unbound and po->pppoe_dev is NULL. Fixes: 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Tested-by: Oleksii Berezhniak <core@irc.lg.ua> Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-22bonding: correct the MAC address for "follow" fail_over_mac policydingtianhong
[ Upstream commit a951bc1e6ba58f11df5ed5ddc41311e10f5fd20b ] The "follow" fail_over_mac policy is useful for multiport devices that either become confused or incur a performance penalty when multiple ports are programmed with the same MAC address, but the same MAC address still may happened by this steps for this policy: 1) echo +eth0 > /sys/class/net/bond0/bonding/slaves bond0 has the same mac address with eth0, it is MAC1. 2) echo +eth1 > /sys/class/net/bond0/bonding/slaves eth1 is backup, eth1 has MAC2. 3) ifconfig eth0 down eth1 became active slave, bond will swap MAC for eth0 and eth1, so eth1 has MAC1, and eth0 has MAC2. 4) ifconfig eth1 down there is no active slave, and eth1 still has MAC1, eth2 has MAC2. 5) ifconfig eth0 up the eth0 became active slave again, the bond set eth0 to MAC1. Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same MAC address, it will break this policy for ACTIVE_BACKUP mode. This patch will fix this problem by finding the old active slave and swap them MAC address before change active slave. Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to 3.10: bond_for_each_slave() takes an extra int paramter] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01usbnet: Get EVENT_NO_RUNTIME_PM bit before it is clearedEugene Shatokhin
[ Upstream commit f50791ac1aca1ac1b0370d62397b43e9f831421a ] It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in usbnet_stop(), but its value should be read before it is cleared when dev->flags is set to 0. The problem was spotted and the fix was provided by Oliver Neukum <oneukum@suse.de>. Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01bonding: fix destruction of bond with devices different from arphrd_etherNikolay Aleksandrov
[ Upstream commit 06f6d1094aa0992432b1e2a0920b0ee86ccd83bf ] When the bonding is being unloaded and the netdevice notifier is unregistered it executes NETDEV_UNREGISTER for each device which should remove the bond's proc entry but if the device enslaved is not of ARPHRD_ETHER type and is in front of the bonding, it may execute bond_release_and_destroy() first which would release the last slave and destroy the bond device leaving the proc entry and thus we will get the following error (with dynamic debug on for bond_netdev_event to see the events order): [ 908.963051] eql: event: 9 [ 908.963052] eql: IFF_SLAVE [ 908.963054] eql: event: 2 [ 908.963056] eql: IFF_SLAVE [ 908.963058] eql: event: 6 [ 908.963059] eql: IFF_SLAVE [ 908.963110] bond0: Releasing active interface eql [ 908.976168] bond0: Destroying bond bond0 [ 908.976266] bond0 (unregistering): Released all slaves [ 908.984097] ------------[ cut here ]------------ [ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575 remove_proc_entry+0x112/0x160() [ 908.984110] remove_proc_entry: removing non-empty directory 'net/bonding', leaking at least 'bond0' [ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore usb_common [last unloaded: bonding] [ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O 4.2.0-rc2+ #8 [ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34 ffff8800358dfda8 [ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40 ffff88003e3a4280 [ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a ffffffff8172ebd0 [ 908.984181] Call Trace: [ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50 [ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0 [ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50 [ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160 [ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30 [bonding] [ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding] [ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70 [ 908.984225] [<ffffffff8142f52d>] ? unregister_pernet_operations+0x8d/0xd0 [ 908.984228] [<ffffffff8142f58d>] ? unregister_pernet_subsys+0x1d/0x30 [ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding] [ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250 [ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0 [ 908.984244] [<ffffffff8152b732>] ? entry_SYSCALL_64_fastpath+0x16/0x75 [ 908.984247] ---[ end trace 7c006ed4abbef24b ]--- Thus remove the proc entry manually if bond_release_and_destroy() is used. Because of the checks in bond_remove_proc_entry() it's not a problem for a bond device to change namespaces (the bug fixed by the Fixes commit) but since commit f9399814927ad ("bonding: Don't allow bond devices to change network namespaces.") that can't happen anyway. Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: a64d49c3dd50 ("bonding: Manage /proc/net/bonding/ entries from the netdev events") Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01tg3: Fix temperature reportingJean Delvare
commit d3d11fe08ccc9bff174fc958722b5661f0932486 upstream. The temperature registers appear to report values in degrees Celsius while the hwmon API mandates values to be exposed in millidegrees Celsius. Do the conversion so that the values reported by "sensors" are correct. Fixes: aed93e0bf493 ("tg3: Add hwmon support for temperature") Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Prashant Sreedharan <prashant@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01rtlwifi: rtl8192cu: Add new device IDAdrien Schildknecht
commit 1642d09fb9b128e8e538b2a4179962a34f38dff9 upstream. The v2 of NetGear WNA1000M uses a different idProduct: USB ID 0846:9043 Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-03ath9k: fix DMA stop sequence for AR9003+Felix Fietkau
commit 300f77c08ded96d33f492aaa02549103852f0c12 upstream. AR93xx and newer needs to stop rx before tx to avoid getting the DMA engine or MAC into a stuck state. This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-22xen: netback: read hotplug script once at start of day.Ian Campbell
[ Upstream commit 31a418986a5852034d520a5bab546821ff1ccf3d ] When we come to tear things down in netback_remove() and generate the uevent it is possible that the xenstore directory has already been removed (details below). In such cases netback_uevent() won't be able to read the hotplug script and will write a xenstore error node. A recent change to the hypervisor exposed this race such that we now sometimes lose it (where apparently we didn't ever before). Instead read the hotplug script configuration during setup and use it for the lifetime of the backend device. The apparently more obvious fix of moving the transition to state=Closed in netback_remove() to after the uevent does not work because it is possible that we are already in state=Closed (in reaction to the guest having disconnected as it shutdown). Being already in Closed means the toolstack is at liberty to start tearing down the xenstore directories. In principal it might be possible to arrange to unregister the device sooner (e.g on transition to Closing) such that xenstore would still be there but this state machine is fragile and prone to anger... A modern Xen system only relies on the hotplug uevent for driver domains, when the backend is in the same domain as the toolstack it will run the necessary setup/teardown directly in the correct sequence wrt xenstore changes. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-22net: dp83640: fix broken calibration routine.Richard Cochran
[ Upstream commit 397a253af5031de4a4612210055935309af4472c ] Currently, the calibration function that corrects the initial offsets among multiple devices only works the first time. If the function is called more than once, the calibration fails and bogus offsets will be programmed into the devices. In a well hidden spot, the device documentation tells that trigger indexes 0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work. This patch fixes the issue by using one of the special triggers during the recalibration method. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-22net: phy: Allow EEE for all RGMII variantsFlorian Fainelli
[ Upstream commit 7e14069651591c81046ffaec13c3dac8cb70f5fb ] RGMII interfaces come in multiple flavors: RGMII with transmit or receive internal delay, no delays at all, or delays in both direction. This change extends the initial check for PHY_INTERFACE_MODE_RGMII to cover all of these variants since EEE should be allowed for any of these modes, since it is a property of the RGMII, hence Gigabit PHY capability more than the RGMII electrical interface and its delays. Fixes: a59a4d192166 ("phy: add the EEE support and the way to access to the MMD registers") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-05rtlwifi: rtl8192cu: Fix kernel deadlockLarry Finger
commit 414b7e3b9ce8b0577f613e656fdbc36b34b444dd upstream. The USB mini-driver in rtlwifi, which is used by rtl8192cu, issues a call to usb_control_msg() with a timeout value of 0. In some instances where the interface is shutting down, this infinite wait results in a CPU deadlock. A one second timeout fixes this problem without affecting any normal operations. This bug is reported at https://bugzilla.novell.com/show_bug.cgi?id=927786. Reported-by: Bernhard Wiedemann <bwiedemann@suse.com> Tested-by: Bernhard Wiedemann <bwiedemann@suse.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Bernhard Wiedemann <bwiedemann@suse.com> Cc: Takashi Iwai<tiwai@suse.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-05rt2x00: add new rt2800usb device DWA 130Scott Branden
commit ea345c145ff23197eab34d0c4d0c8a93d7bea8c6 upstream. Add the USB Id to link the D-Link DWA 130 USB Wifi adapter to the rt2830 driver. Signed-off-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Pieter Truter <ptruter@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06wl18xx: show rx_frames_per_rates as an array as it really isNicolas Iooss
commit a3fa71c40f1853d0c27e8f5bc01a722a705d9682 upstream. In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an array, not a number. This means WL18XX_DEBUGFS_FWSTATS_FILE can't be used to display this field in debugfs (it would display a pointer, not the actual data). Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead. This bug has been found by adding a __printf attribute to wl1271_format_buffer. gcc complained about "format '%u' expects argument of type 'unsigned int', but argument 5 has type 'u32 *'". Fixes: c5d94169e818 ("wl18xx: use new fw stats structures") Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06e1000: add dummy allocator to fix race condition between mtu change and netpollSabrina Dubroca
commit 08e8331654d1d7b2c58045e549005bc356aa7810 upstream. There is a race condition between e1000_change_mtu's cleanups and netpoll, when we change the MTU across jumbo size: Changing MTU frees all the rx buffers: e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings -> e1000_clean_rx_ring Then, close to the end of e1000_change_mtu: pr_info -> ... -> netpoll_poll_dev -> e1000_clean -> e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag And when we come back to do the rest of the MTU change: e1000_up -> e1000_configure -> e1000_configure_rx -> e1000_alloc_jumbo_rx_buffers alloc_jumbo finds the buffers already != NULL, since data (shared with page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage, or at least not what is expected when in jumbo state. This results in an unusable adapter (packets don't get through), and a NULL pointer dereference on the next call to e1000_clean_rx_ring (other mtu change, link down, shutdown): BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330 [...] Call Trace: [<ffffffff81195445>] put_page+0x55/0x60 [<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200 [<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60 [<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0 [<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840 [<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170 [<ffffffff81647050>] dev_set_mtu+0xa0/0x140 [<ffffffff81664218>] do_setlink+0x218/0xac0 [<ffffffff814459e9>] ? nla_parse+0xb9/0x120 [<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890 [<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40 [<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100 [<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260 By setting the allocator to a dummy version, netpoll can't mess up our rx buffers. The allocator is set back to a sane value in e1000_configure_rx. Fixes: edbbb3ca1077 ("e1000: implement jumbo receive with partial descriptors") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06rtlwifi: rtl8192cu: Add new device IDMarek Vasut
commit 9374e7d2fdcad3c36dafc8d3effd554bc702c4b6 upstream. Add new ID for ASUS N10 WiFi dongle. Signed-off-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: John W. Linville <linville@tuxdriver.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06rtlwifi: rtl8192cu: Add new USB IDLarry Finger
commit 2f92b314f4daff2117847ac5343c54d3d041bf78 upstream. USB ID 2001:330d is used for a D-Link DWA-131. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-29benet: Call dev_kfree_skby_any instead of kfree_skb.Eric W. Biederman
Replace free_skb with dev_kfree_skb_any in be_tx_compl_process as which can be called in hard irq by netpoll, softirq context by normal napi polling, and in normal sleepable context by the network device close method. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-29ixgb: Call dev_kfree_skby_any instead of dev_kfree_skb.Eric W. Biederman
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can be called in hard irq and other contexts. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-29tg3: Call dev_kfree_skby_any instead of dev_kfree_skb.Eric W. Biederman
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can be called in hard irq and other contexts. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-29bnx2: Call dev_kfree_skby_any instead of dev_kfree_skb.Eric W. Biederman
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can be called in hard irq and other contexts. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-29r8169: Call dev_kfree_skby_any instead of dev_kfree_skb.Eric W. Biederman
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can be called in hard irq and other contexts. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-298139too: Call dev_kfree_skby_any instead of dev_kfree_skb.Eric W. Biederman
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can be called in hard irq and other contexts. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-298139cp: Call dev_kfree_skby_any instead of kfree_skb.Eric W. Biederman
Replace kfree_skb with dev_kfree_skb_any in cp_start_xmit as it can be called in both hard irq and other contexts. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-19iwlwifi: dvm: run INIT firmware again upon .start()Emmanuel Grumbach
commit 9c8928f5176766bec79f272bd47b7124e11cccbd upstream. The assumption before this patch was that we don't need to run again the INIT firmware after the system booted. The INIT firmware runs calibrations which impact the physical layer's behavior. Users reported that it may be helpful to run these calibrations again every time the interface is brought up. The penatly is minimal, since the calibrations run fast. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=94341 Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-13net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5}Markos Chandras
commit 87f966d97b89774162df04d2106c6350c8fe4cb3 upstream. On a MIPS Malta board, tons of fifo underflow errors have been observed when using u-boot as bootloader instead of YAMON. The reason for that is that YAMON used to set the pcnet device to SRAM mode but u-boot does not. As a result, the default Tx threshold (64 bytes) is now too small to keep the fifo relatively used and it can result to Tx fifo underflow errors. As a result of which, it's best to setup the SRAM on supported controllers so we can always use the NOUFLO bit. Cc: <netdev@vger.kernel.org> Cc: <linux-kernel@vger.kernel.org> Cc: Don Fry <pcnet32@frontier.com> Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-13Revert "iwlwifi: mvm: fix failure path when power_update fails in add_interface"Greg Kroah-Hartman
This reverts commit fce2d025479af5e1fa6717480c7853cdfb8b71aa It was incorrectly applied, as it merged with fuzz. Reported-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
2015-03-26can: add missing initialisations in CAN related skbuffsOliver Hartkopp
commit 969439016d2cf61fef53a973d7e6d2061c3793b1 upstream. When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient this can lead to a skb_under_panic due to missing skb initialisations. Add the missing initialisations at the CAN skbuff creation times on driver level (rx path) and in the network layer (tx path). Reported-by: Austin Schuh <austin@peloton-tech.com> Reported-by: Daniel Steer <daniel.steer@mclaren.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26Revert "net: cx82310_eth: use common match macro"Ondrej Zary
[ Upstream commit 8d006e0105978619fb472e150c88b0d49337fe2b ] This reverts commit 11ad714b98f6d9ca0067568442afe3e70eb94845 because it breaks cx82310_eth. The custom USB_DEVICE_CLASS macro matches bDeviceClass, bDeviceSubClass and bDeviceProtocol but the common USB_DEVICE_AND_INTERFACE_INFO matches bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are not specified. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-18ath5k: fix spontaneus AR5312 freezesSergey Ryazanov
commit 8bfae4f9938b6c1f033a5159febe97e441d6d526 upstream. Sometimes while CPU have some load and ath5k doing the wireless interface reset the whole WiSoC completely freezes. Set of tests shows that using atomic delay function while we wait interface reset helps to avoid such freezes. The easiest way to reproduce this issue: create a station interface, start continous scan with wpa_supplicant and load CPU by something. Or just create multiple station interfaces and put them all in continous scan. This patch partially reverts the commit 1846ac3dbec0 ("ath5k: Use usleep_range where possible"), which replaces initial udelay() by usleep_range(). I do not know actual source of this issue, but all looks like that HW freeze is caused by transaction on internal SoC bus, while wireless block is in reset state. Also I should note that I do not know how many chips are affected, but I did not see this issue with chips, other than AR5312. CC: Jiri Slaby <jirislaby@gmail.com> CC: Nick Kossifidis <mickflemm@gmail.com> CC: Luis R. Rodriguez <mcgrof@do-not-panic.com> Fixes: 1846ac3dbec0 ("ath5k: Use usleep_range where possible") Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com> Tested-by: Eric Bree <ebree@nltinc.com> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-18team: don't traverse port list using rcu in team_set_mac_addressJiri Pirko
[ Upstream commit 9215f437b85da339a7dfe3db6e288637406f88b2 ] Currently the list is traversed using rcu variant. That is not correct since dev_set_mac_address can be called which eventually calls rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this by remove the rcu usage here. Fixes: 3d249d4ca7 "net: introduce ethernet teaming device" Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-18usb: plusb: Add support for National Instruments host-to-host cableBen Shelton
[ Upstream commit 42c972a1f390e3bc51ca1e434b7e28764992067f ] The National Instruments USB Host-to-Host Cable is based on the Prolific PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it. Signed-off-by: Ben Shelton <ben.shelton@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-18macvtap: make sure neighbour code can push ethernet headerEric Dumazet
[ Upstream commit 2f1d8b9e8afa5a833d96afcd23abcb8cdf8d83ab ] Brian reported crashes using IPv6 traffic with macvtap/veth combo. I tracked the crashes in neigh_hh_output() -> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD); Neighbour code assumes headroom to push Ethernet header is at least 16 bytes. It appears macvtap has only 14 bytes available on arches where NET_IP_ALIGN is 0 (like x86) Effect is a corruption of 2 bytes right before skb->head, and possible crashes if accessing non existing memory. This fix should also increase IPv4 performance, as paranoid code in ip_finish_output2() wont have to call skb_realloc_headroom() Reported-by: Brian Rak <brak@vultr.com> Tested-by: Brian Rak <brak@vultr.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-18team: fix possible null pointer dereference in team_handle_frameJiri Pirko
[ Upstream commit 57e595631904c827cfa1a0f7bbd7cc9a49da5745 ] Currently following race is possible in team: CPU0 CPU1 team_port_del team_upper_dev_unlink priv_flags &= ~IFF_TEAM_PORT team_handle_frame team_port_get_rcu team_port_exists priv_flags & IFF_TEAM_PORT == 0 return NULL (instead of port got from rx_handler_data) netdev_rx_handler_unregister The thing is that the flag is removed before rx_handler is unregistered. If team_handle_frame is called in between, team_port_exists returns 0 and team_port_get_rcu will return NULL. So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister that team_handle_frame will always see valid rx_handler_data pointer. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-18net: phy: Fix verification of EEE support in phy_init_eeeGuenter Roeck
[ Upstream commit 54da5a8be3c1e924c35480eb44c6e9b275f6444e ] phy_init_eee uses phy_find_setting(phydev->speed, phydev->duplex) to find a valid entry in the settings array for the given speed and duplex value. For full duplex 1000baseT, this will return the first matching entry, which is the entry for 1000baseKX_Full. If the phy eee does not support 1000baseKX_Full, this entry will not match, causing phy_init_eee to fail for no good reason. Fixes: 9a9c56cb34e6 ("net: phy: fix a bug when verify the EEE support") Fixes: 3e7077067e80c ("phy: Expand phy speed/duplex settings array") Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-06iwlwifi: mvm: always use mac color zeroLuciano Coelho
commit 5523d11cc46393a1e61b7ef4a0b2d4e7ed9521e4 upstream. We don't really need to use different mac colors when adding mac contexts, because they're not used anywhere. In fact, the firmware doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401 when we reach that. Remove the color increment to use always zero and avoid reaching 255. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-06iwlwifi: mvm: fix failure path when power_update fails in add_interfaceLuciano Coelho
commit fd66fc1cafd72ddf27dbec3a5e29e99839d1bc84 upstream. When iwl_mvm_power_update_mac() is called, we have already added the mac context, so if this call fails we should remove the mac. Fixes: commit e5e7aa8e2561 ('iwlwifi: mvm: refactor power code') Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-06iwlwifi: mvm: validate tid and sta_id in ba_notifEyal Shapira
commit 2cee4762c528a9bd2cdff793197bf591a2196c11 upstream. These are coming from the FW and are used to access arrays. Bad values can cause an out of bounds access so discard such ba_notifs and warn. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-06iwlwifi: pcie: disable the SCD_BASE_ADDR when we resume from WoWLANEmmanuel Grumbach
commit cd8f438405032ac8ff88bd8f2eca5e0c0063b14b upstream. The base address of the scheduler in the device's memory (SRAM) comes from two different sources. The periphery register and the alive notification from the firmware. We have a check in iwl_pcie_tx_start that ensures that they are the same. When we resume from WoWLAN, the firmware may have crashed for whatever reason. In that case, the whole device may be reset which means that the periphery register will hold a meaningless value. When we come to compare trans_pcie->scd_base_addr (which really holds the value we had when we loaded the WoWLAN firmware upon suspend) and the current value of the register, we don't see a match unsurprisingly. Trick the check to avoid a loud yet harmless WARN. Note that when the WoWLAN has crashed, we will see that in iwl_trans_pcie_d3_resume which will let the op_mode know. Once the op_mode is informed that the WowLAN firmware has crashed, it can't do much besides resetting the whole device. Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-26ppp: deflate: never return len larger than output bufferFlorian Westphal
[ Upstream commit e2a4800e75780ccf4e6c2487f82b688ba736eb18 ] When we've run out of space in the output buffer to store more data, we will call zlib_deflate with a NULL output buffer until we've consumed remaining input. When this happens, olen contains the size the output buffer would have consumed iff we'd have had enough room. This can later cause skb_over_panic when ppp_generic skb_put()s the returned length. Reported-by: Iain Douglas <centos@1n6.org.uk> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-26netxen: fix netxen_nic_poll() logicEric Dumazet
[ Upstream commit 6088beef3f7517717bd21d90b379714dd0837079 ] NAPI poll logic now enforces that a poller returns exactly the budget when it wants to be called again. If a driver limits TX completion, it has to return budget as well when the limit is hit, not the number of received packets. Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: d75b1ade567f ("net: less interrupt masking in NAPI") Cc: Manish Chopra <manish.chopra@qlogic.com> Acked-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-05drivers: net: cpsw: discard dual emac default vlan configurationMugunthan V N
commit 02a54164c52ed6eca3089a0d402170fbf34d6cf5 upstream. In Dual EMAC, the default VLANs are used to segregate Rx packets between the ports, so adding the same default VLAN to the switch will affect the normal packet transfers. So returning error on addition of dual EMAC default VLANs. Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to break dual EMAC port separations. Fixes: d9ba8f9e6298 (driver: net: ethernet: cpsw: dual emac interface implementation) Reported-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-05can: kvaser_usb: Fix state handling upon BUS_ERROR eventsAhmed S. Darwish
commit e638642b08c170d2021b706f0b1c4f4ae93d8cbd upstream. While being in an ERROR_WARNING state, and receiving further bus error events with error counters still in the ERROR_WARNING range of 97-127 inclusive, the state handling code erroneously reverts back to ERROR_ACTIVE. Per the CAN standard, only revert to ERROR_ACTIVE when the error counters are less than 96. Moreover, in certain Kvaser models, the BUS_ERROR flag is always set along with undefined bits in the M16C status register. Thus use bitwise operators instead of full equality for checking that register against bus errors. Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-05can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUTAhmed S. Darwish
commit 14c10c2a1dd8eb8e00b750b521753260befa2789 upstream. On some x86 laptops, plugging a Kvaser device again after an unplug makes the firmware always ignore the very first command. For such a case, provide some room for retries instead of completely exiting the driver init code. Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-05can: kvaser_usb: Send correct context to URB completionAhmed S. Darwish
commit 3803fa6977f1de15fda4e8646c8fec97c8045cae upstream. Send expected argument to the URB completion hander: a CAN netdevice instead of the network interface private context `kvaser_usb_net_priv'. This was discovered by having some garbage in the kernel log in place of the netdevice names: can0 and can1. Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-05can: kvaser_usb: Do not sleep in atomic contextAhmed S. Darwish
commit ded5006667318c06df875609535176bd33f243a1 upstream. Upon receiving a hardware event with the BUS_RESET flag set, the driver kills all of its anchored URBs and resets all of its transmit URB contexts. Unfortunately it does so under the context of URB completion handler `kvaser_usb_read_bulk_callback()', which is often called in an atomic context. While the device is flooded with many received error packets, usb_kill_urb() typically sleeps/reschedules till the transfer request of each killed URB in question completes, leading to the sleep in atomic bug. [3] In v2 submission of the original driver patch [1], it was stated that the URBs kill and tx contexts reset was needed since we don't receive any tx acknowledgments later and thus such resources will be locked down forever. Fortunately this is no longer needed since an earlier bugfix in this patch series is now applied: all tx URB contexts are reset upon CAN channel close. [2] Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF event, which is the recommended handling method advised by the device manufacturer. [1] http://article.gmane.org/gmane.linux.network/239442 http://www.webcitation.org/6Vr2yagAQ [2] can: kvaser_usb: Reset all URB tx contexts upon channel close 889b77f7fd2bcc922493d73a4c51d8a851505815 [3] Stacktrace: <IRQ> [<ffffffff8158de87>] dump_stack+0x45/0x57 [<ffffffff8158b60c>] __schedule_bug+0x41/0x4f [<ffffffff815904b1>] __schedule+0x5f1/0x700 [<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10 [<ffffffff81590684>] schedule+0x24/0x70 [<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0 [<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110 [<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80 [<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb] [<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb] [<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20 [<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb] [<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0 [<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110 [<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd] [<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20 [<ffffffff81069f65>] ? local_clock+0x15/0x30 [<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd] [<ffffffff814fbb31>] ? process_backlog+0xb1/0x130 [<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd] [<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30 [<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120 [<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60 [<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110 [<ffffffff81004dfd>] handle_irq+0x1d/0x30 [<ffffffff81004727>] do_IRQ+0x57/0x100 [<ffffffff8159482a>] common_interrupt+0x6a/0x6a Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-29can: dev: fix crtlmode_supported checkOliver Hartkopp
commit 9b1087aa5e86448fe6ad40a58964e35f3ba423d5 upstream. When changing flags in the CAN drivers ctrlmode the provided new content has to be checked whether the bits are allowed to be changed. The bits that are to be changed are given as a bitfield in cm->mask. Therefore checking against cm->flags is wrong as the content can hold any kind of values. The iproute2 tool sets the bits in cm->mask and cm->flags depending on the detected command line options. To be robust against bogus user space applications additionally sanitize the provided flags with the provided mask. Cc: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-27can: kvaser_usb: Don't send a RESET_CHIP for non-existing channelsAhmed S. Darwish
commit 5e7e6e0c9b47a45576c38b4a72d67927a5e049f7 upstream. Recent Leaf firmware versions (>= 3.1.557) do not allow to send commands for non-existing channels. If a command is sent for a non-existing channel, the firmware crashes. Reported-by: Christopher Storah <Christopher.Storah@invetech.com.au> Signed-off-by: Olivier Sobrie <olivier@sobrie.be> Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-27can: kvaser_usb: Reset all URB tx contexts upon channel closeAhmed S. Darwish
commit 889b77f7fd2bcc922493d73a4c51d8a851505815 upstream. Flooding the Kvaser CAN to USB dongle with multiple reads and writes in very high frequency (*), closing the CAN channel while all the transmissions are on (#), opening the device again (@), then sending a small number of packets would make the driver enter an almost infinite loop of: [....] [15959.853988] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853990] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853991] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853993] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853994] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853995] kvaser_usb 4-3:1.0 can0: cannot find free context [....] _dragging the whole system down_ in the process due to the excessive logging output. Initially, this has caused random panics in the kernel due to a buggy error recovery path. That got fixed in an earlier commit.(%) This patch aims at solving the root cause. --> 16 tx URBs and contexts are allocated per CAN channel per USB device. Such URBs are protected by: a) A simple atomic counter, up to a value of MAX_TX_URBS (16) b) A flag in each URB context, stating if it's free c) The fact that ndo_start_xmit calls are themselves protected by the networking layers higher above After grabbing one of the tx URBs, if the driver noticed that all of them are now taken, it stops the netif transmission queue. Such queue is worken up again only if an acknowedgment was received from the firmware on one of our earlier-sent frames. Meanwhile, upon channel close (#), the driver sends a CMD_STOP_CHIP to the firmware, effectively closing all further communication. In the high traffic case, the atomic counter remains at MAX_TX_URBS, and all the URB contexts remain marked as active. While opening the channel again (@), it cannot send any further frames since no more free tx URB contexts are available. Reset all tx URB contexts upon CAN channel close. (*) 50 parallel instances of `cangen0 -g 0 -ix` (#) `ifconfig can0 down` (@) `ifconfig can0 up` (%) "can: kvaser_usb: Don't free packets when tight on URBs" Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-08 06:49:46 +0000