aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2015-12-09ath10k: fix invalid NSS for 4x4 devicesRajkumar Manoharan
commit f680f70adbeab28b35f849016b964dd645db6237 upstream. The number of spatial streams that are derived from chain mask for 4x4 devices is using wrong bitmask and conditional check. This is affecting downlink throughput for QCA99x0 devices. Earlier cfg_tx_chainmask is not filled by default until user configured it and so get_nss_from_chainmask never be called. This issue is exposed by recent commit 166de3f1895d ("ath10k: remove supported chain mask"). By default maximum supported chain mask is filled in cfg_tx_chainmask. Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation") Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09can: sja1000: clear interrupts on startMirza Krak
commit 7cecd9ab80f43972c056dc068338f7bcc407b71c upstream. According to SJA1000 data sheet error-warning (EI) interrupt is not cleared by setting the controller in to reset-mode. Then if we have the following case: - system is suspended (echo mem > /sys/power/state) and SJA1000 is left in operating state - A bus error condition occurs which activates EI interrupt, system is still suspended which means EI interrupt will be not be handled nor cleared. If the above two events occur, on resume there is no way to return the SJA1000 to operating state, except to cycle power to it. By simply reading the IR register on start we will clear any previous conditions that could be present. Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com> Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09can: Use correct type in sizeof() in nla_put()Marek Vasut
commit 562b103a21974c2f9cd67514d110f918bb3e1796 upstream. The sizeof() is invoked on an incorrect variable, likely due to some copy-paste error, and this might result in memory corruption. Fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: netdev@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09mwifiex: fix mwifiex_rdeeprom_read()Dan Carpenter
commit 1f9c6e1bc1ba5f8a10fcd6e99d170954d7c6d382 upstream. There were several bugs here. 1) The done label was in the wrong place so we didn't copy any information out when there was no command given. 2) We were using PAGE_SIZE as the size of the buffer instead of "PAGE_SIZE - pos". 3) snprintf() returns the number of characters that would have been printed if there were enough space. If there was not enough space (and we had fixed the memory corruption bug #2) then it would result in an information leak when we do simple_read_from_buffer(). I've changed it to use scnprintf() instead. I also removed the initialization at the start of the function, because I thought it made the code a little more clear. Fixes: 5e6e3a92b9a4 ('wireless: mwifiex: initial commit for Marvell mwifiex driver') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09net: mvneta: Fix CPU_MAP registers initialisationMaxime Ripard
commit 2502d0ef272da7058ef303b849a2c8dc324c2e2e upstream. The CPU_MAP register is duplicated for each CPUs at different addresses, each instance being at a different address. However, the code so far was using CONFIG_NR_CPUS to initialise the CPU_MAP registers for each registers, while the SoCs embed at most 4 CPUs. This is especially an issue with multi_v7_defconfig, where CONFIG_NR_CPUS is currently set to 16, resulting in writes to registers that are not CPU_MAP. Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09iwlwifi: Add new PCI IDs for the 8260 seriesOren Givon
commit 4ab75944c4b324c1f5f01dbd4c4d122d2b9da187 upstream. Add some new PCI IDs for the 8260 series which were missing. The following sub-system IDs were added: 0x0130, 0x1130, 0x0132, 0x1132, 0x1150, 0x8110, 0x9110, 0x8130, 0x9130, 0x8132, 0x9132, 0x8150, 0x9150, 0x0044, 0x0930 Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09iwlwifi: pcie: fix (again) prepare card flowEmmanuel Grumbach
commit 03a19cbb91994212be72ce15ac3406fa9f8ba079 upstream. The hardware bug in the commit mentioned below forces us not to re-enable the clock gating in the Host Cluster. The impact on the power consumption is minimal and it allows the WAKE_ME interrupt to propagate. Fixes: c9fdec9f3970 ("iwlwifi: pcie: fix prepare card flow") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09virtio-net: drop NETIF_F_FRAGLISTJason Wang
[ Upstream commit 48900cb6af4282fa0fb6ff4d72a81aa3dadb5c39 ] virtio declares support for NETIF_F_FRAGLIST, but assumes that there are at most MAX_SKB_FRAGS + 2 fragments which isn't always true with a fraglist. A longer fraglist in the skb will make the call to skb_to_sgvec overflow the sg array, leading to memory corruption. Drop NETIF_F_FRAGLIST so we only get what we can handle. Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09sfc: push partner queue for skb->xmit_moreMartin Habets
[ Upstream commit b2663a4f30e85ec606b806f5135413e6d5c78d1e ] When the IP stack passes SKBs the sfc driver puts them in 2 different TX queues (called partners), one for checksummed and one for not checksummed. If the SKB has xmit_more set the driver will delay pushing the work to the NIC. When later it does decide to push the buffers this patch ensures it also pushes the partner queue, if that also has any delayed work. Before this fix the work in the partner queue would be left for a long time and cause a netdev watchdog. Fixes: 70b33fb ("sfc: add support for skb->xmit_more") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09stmmac: Correctly report PTP capabilities.Phil Reid
[ Upstream commit e6dbe1eb2db0d7a14991c06278dd3030c45fb825 ] priv->hwts_*_en indicate if timestamping is enabled/disabled at run time. But priv->dma_cap.time_stamp and priv->dma_cap.atime_stamp indicates HW is support for PTPv1/PTPv2. Signed-off-by: Phil Reid <preid@electromag.com.au> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09net/mlx4: Copy/set only sizeof struct mlx4_eqe bytesCarol L Soto
[ Upstream commit c02b05011fadf8e409e41910217ca689f2fc9d91 ] When doing memcpy/memset of EQEs, we should use sizeof struct mlx4_eqe as the base size and not caps.eqe_size which could be bigger. If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt data in the master context. When using a 64 byte stride, the memcpy copied over 63 bytes to the slave_eq structure. This resulted in copying over the entire eqe of interest, including its ownership bit -- and also 31 bytes of garbage into the next WQE in the slave EQ -- which did NOT include the ownership bit (and therefore had no impact). However, once the stride is increased to 128, we are overwriting the ownership bits of *three* eqes in the slave_eq struct. This results in an incorrect ownership bit for those eqes, which causes the eq to seem to be full. The issue therefore surfaced only once 128-byte EQEs started being used in SRIOV and (overarchitectures that have 128/256 byte cache-lines such as PPC) - e.g after commit 77507aa249ae "net/mlx4_core: Enable CQE/EQE stride support". Fixes: 08ff32352d6f ('mlx4: 64-byte CQE/EQE support') Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09ppp: fix pppoe_dev deletion condition in pppoe_release()Guillaume Nault
[ Upstream commit 1acea4f6ce1b1c0941438aca75dd2e5c6b09db60 ] We can't rely on PPPOX_ZOMBIE to decide whether to clear po->pppoe_dev. PPPOX_ZOMBIE can be set by pppoe_disc_rcv() even when po->pppoe_dev is NULL. So we have no guarantee that (sk->sk_state & PPPOX_ZOMBIE) implies (po->pppoe_dev != NULL). Since we're releasing a PPPoE socket, we want to release the pppoe_dev if it exists and reset sk_state to PPPOX_DEAD, no matter the previous value of sk_state. So we can just check for po->pppoe_dev and avoid any assumption on sk->sk_state. Fixes: 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09macvtap: unbreak receiving of gro skb with frag listJason Wang
[ Upstream commit f23d538bc24a83c16127c2eb82c9cf1adc2b5149 ] We don't have fraglist support in TAP_FEATURES. This will lead software segmentation of gro skb with frag list. Fixes by having frag list support in TAP_FEATURES. With this patch single session of netperf receiving were restored from about 5Gb/s to about 12Gb/s on mlx4. Fixes a567dd6252 ("macvtap: simplify usage of tap_features") Cc: Vlad Yasevich <vyasevic@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-09qmi_wwan: add Sierra Wireless MC74xx/EM74xxBjørn Mork
[ Upstream commit 0db65fcfcded76fe4f74e3ca9f4e2baf67b683ef ] New device IDs shamelessly lifted from the vendor driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09iwlwifi: pci: add a few more PCI subvendor IDs for the 7265 seriesLuca Coelho
commit f08f625876476b6c4a87834dc86e3b927f4697d2 upstream. Add 3 new subdevice IDs for the 0x095A device ID and 2 for the 0x095B device ID. Reported-by: Jeremy <jeremy.bomkamp@gmail.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09iwlwifi: mvm: flush fw_dump_wk when mvm fails to startAndrei Otcheretianski
commit dbf73d4a8bb8f4e1d1f3edd3be825692279e2ef3 upstream. FW dump may be triggered when running init ucode, for example due to a sysassert. In this case fw_dump_wk may run after mvm is freed, resulting in a kernel panic. Fix it by flushing the work. Fixes: 01b988a708af ("iwlwifi: mvm: allow to collect debug data when restart is disabled") Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09iwlwifi: mvm: init card correctly on ctkill exit checkArik Nemtsov
commit 1a3fe0b2b6778b7866e2b3f5c9a299d5e9bbd89c upstream. During the CT-kill exit flow, the card is powered up and partially initialized to check if the temperature is already low enough. Unfortunately the init bails early because the CT-kill flag is set. Make the code bail early only for HW RF-kill, as was intended by the author. CT-kill is self-imposed and is not really RF-kill. Fixes: 31b8b343e019 ("iwlwifi: fix RFkill while calibrating") Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09iwlwifi: mvm: fix D3 firmware PN programmingJohannes Berg
commit 2cf5eb3ab7bb7f2e3a70edcef236cd62c87db030 upstream. The code to send the RX PN data (for each TID) to the firmware has a devastating bug: it overwrites the data for TID 0 with all the TID data, leaving the remaining TIDs zeroed. This will allow replays to actually be accepted by the firmware, which could allow waking up the system. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09iwlwifi: mvm: clear csa countdown when AP is stoppedAvraham Stern
commit e9cb0327b26dd7ba43a3b7a05b4b62219decf42d upstream. The csa_countdown flag was not cleared when the AP is stopped. As a result, if the AP was stopped after csa_countdown had started, all the folowing channel switch commands would fail. Fix that by clearing the csa_countdown flag when the AP is stopped. Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09rtlwifi: rtl8821ae: Fix system lockups on bootLarry Finger
commit 54328e64047a54b8fc2362c2e1f0fa16c90f739f upstream. In commit 1277fa2ab2f9 ("rtlwifi: Remove the clear interrupt routine from all drivers"), the code that cleared all interrupt enable bits before setting them was removed for all PCI drivers. This fixed an issue that caused TX to be blocked for 3-5 seconds. On some RTL8821AE units, this change causes soft lockups to occur on boot. For that reason, the portion of the earlier commit that applied to rtl8821ae is reverted. Kernels 4.1 and newer are affected. See http://marc.info/?l=linux-wireless&m=144373370103285&w=2 and https://bugzilla.opensuse.org/show_bug.cgi?id=944978 for two cases where this regression affected user systems. Note that this bug does not appear on any of the developer's setups. For those users whose systems are affected by the TX blockage, but do not lock up on boot, a module parameter is added to disable the interrupt clear Fixes: 1277fa2ab2f9 ("rtlwifi: Remove the clear interrupt routine from all drivers") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09iwlwifi: fix firmware filename for 3160Johannes Berg
commit b5a48134f8af08f5243328f8a0b05fc5ae7cf343 upstream. The MODULE_FIRMWARE() for 3160 should be using the 7260 version as it's done in the device configuration struct instead of referencing IWL3160_UCODE_API_OK which doesn't even exist. Reported-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09iwlwifi: dvm: fix D3 firmware PN programmingJohannes Berg
commit 5bd166872d8f99f156fac191299d24f828bb2348 upstream. The code to send the RX PN data (for each TID) to the firmware has a devastating bug: it overwrites the data for TID 0 with all the TID data, leaving the remaining TIDs zeroed. This will allow replays to actually be accepted by the firmware, which could allow waking up the system. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09ath9k: declare required extra tx headroomFelix Fietkau
commit 029cd0370241641eb70235d205aa0b90c84dce44 upstream. ath9k inserts padding between the 802.11 header and the data area (to align it). Since it didn't declare this extra required headroom, this led to some nasty issues like randomly dropped packets in some setups. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-27ppp: don't override sk->sk_state in pppoe_flush_dev()Guillaume Nault
[ Upstream commit e6740165b8f7f06d8caee0fceab3fb9d790a6fed ] Since commit 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release"), pppoe_release() calls dev_put(po->pppoe_dev) if sk is in the PPPOX_ZOMBIE state. But pppoe_flush_dev() can set sk->sk_state to PPPOX_ZOMBIE _and_ reset po->pppoe_dev to NULL. This leads to the following oops: [ 570.140800] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e0 [ 570.142931] IP: [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] PGD 3d119067 PUD 3dbc1067 PMD 0 [ 570.144601] Oops: 0000 [#1] SMP [ 570.144601] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppoe pppox ppp_generic slhc loop crc32c_intel ghash_clmulni_intel jitterentropy_rng sha256_generic hmac drbg ansi_cprng aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper acpi_cpufreq evdev serio_raw processor button ext4 crc16 mbcache jbd2 virtio_net virtio_blk virtio_pci virtio_ring virtio [ 570.144601] CPU: 1 PID: 15738 Comm: ppp-apitest Not tainted 4.2.0 #1 [ 570.144601] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014 [ 570.144601] task: ffff88003d30d600 ti: ffff880036b60000 task.ti: ffff880036b60000 [ 570.144601] RIP: 0010:[<ffffffffa018c701>] [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP: 0018:ffff880036b63e08 EFLAGS: 00010202 [ 570.144601] RAX: 0000000000000000 RBX: ffff880034340000 RCX: 0000000000000206 [ 570.144601] RDX: 0000000000000006 RSI: ffff88003d30dd20 RDI: ffff88003d30dd20 [ 570.144601] RBP: ffff880036b63e28 R08: 0000000000000001 R09: 0000000000000000 [ 570.144601] R10: 00007ffee9b50420 R11: ffff880034340078 R12: ffff8800387ec780 [ 570.144601] R13: ffff8800387ec7b0 R14: ffff88003e222aa0 R15: ffff8800387ec7b0 [ 570.144601] FS: 00007f5672f48700(0000) GS:ffff88003fc80000(0000) knlGS:0000000000000000 [ 570.144601] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 570.144601] CR2: 00000000000004e0 CR3: 0000000037f7e000 CR4: 00000000000406a0 [ 570.144601] Stack: [ 570.144601] ffffffffa018f240 ffff8800387ec780 ffffffffa018f240 ffff8800387ec7b0 [ 570.144601] ffff880036b63e48 ffffffff812caabe ffff880039e4e000 0000000000000008 [ 570.144601] ffff880036b63e58 ffffffff812cabad ffff880036b63ea8 ffffffff811347f5 [ 570.144601] Call Trace: [ 570.144601] [<ffffffff812caabe>] sock_release+0x1a/0x75 [ 570.144601] [<ffffffff812cabad>] sock_close+0xd/0x11 [ 570.144601] [<ffffffff811347f5>] __fput+0xff/0x1a5 [ 570.144601] [<ffffffff811348cb>] ____fput+0x9/0xb [ 570.144601] [<ffffffff81056682>] task_work_run+0x66/0x90 [ 570.144601] [<ffffffff8100189e>] prepare_exit_to_usermode+0x8c/0xa7 [ 570.144601] [<ffffffff81001a26>] syscall_return_slowpath+0x16d/0x19b [ 570.144601] [<ffffffff813babb1>] int_ret_from_sys_call+0x25/0x9f [ 570.144601] Code: 48 8b 83 c8 01 00 00 a8 01 74 12 48 89 df e8 8b 27 14 e1 b8 f7 ff ff ff e9 b7 00 00 00 8a 43 12 a8 0b 74 1c 48 8b 83 a8 04 00 00 <48> 8b 80 e0 04 00 00 65 ff 08 48 c7 83 a8 04 00 00 00 00 00 00 [ 570.144601] RIP [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP <ffff880036b63e08> [ 570.144601] CR2: 00000000000004e0 [ 570.200518] ---[ end trace 46956baf17349563 ]--- pppoe_flush_dev() has no reason to override sk->sk_state with PPPOX_ZOMBIE. pppox_unbind_sock() already sets sk->sk_state to PPPOX_DEAD, which is the correct state given that sk is unbound and po->pppoe_dev is NULL. Fixes: 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Tested-by: Oleksii Berezhniak <core@irc.lg.ua> Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-27net/ibm/emac: bump version numbers for correct work with ethtoolIvan Mikhaylov
[ Upstream commit 661dfc65f7981481ba2e31aaa702371e82336e56 ] The size of the MAC register dump used to be the size specified by the reg property in the device tree. Userland has no good way of finding out that size, and it was not specified consistently for each MAC type, so ethtool would end up printing junk at the end of the register dump if the device tree didn't match the size it assumed. Using the new version numbers indicates unambiguously that the size of the MAC register dump is dependent only on the MAC type. Fixes: 5369c71f7ca2 ("net/ibm/emac: fix size of emac dump memory areas") Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-22igb: do not re-init SR-IOV during probeStefan Assmann
commit 6423fc34160939142d72ffeaa2db6408317f54df upstream. During driver probing the following code path is triggered. igb_probe ->igb_sw_init ->igb_probe_vfs ->igb_pci_enable_sriov ->igb_sriov_reinit Doing the SR-IOV re-init is not necessary during probing since we're starting from scratch. Here we can call igb_enable_sriov() right away. Running igb_sriov_reinit() during igb_probe() also seems to cause occasional packet loss on some onboard 82576 NICs. Reproduced on Dell and HP servers with onboard 82576 NICs. Example: Intel Corporation 82576 Gigabit Network Connection [8086:10c9] (rev 01) Subsystem: Dell Device [1028:0481] Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Daniel J Blueman <daniel@numascale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-22net/xen-netfront: only napi_synchronize() if runningChas Williams
commit 274b045509175db0405c784be85e8cce116e6f7d upstream. If an interface isn't running napi_synchronize() will hang forever. [ 392.248403] rmmod R running task 0 359 343 0x00000000 [ 392.257671] ffff88003760fc88 ffff880037193b40 ffff880037193160 ffff88003760fc88 [ 392.267644] ffff880037610000 ffff88003760fcd8 0000000100014c22 ffffffff81f75c40 [ 392.277524] 0000000000bc7010 ffff88003760fca8 ffffffff81796927 ffffffff81f75c40 [ 392.287323] Call Trace: [ 392.291599] [<ffffffff81796927>] schedule+0x37/0x90 [ 392.298553] [<ffffffff8179985b>] schedule_timeout+0x14b/0x280 [ 392.306421] [<ffffffff810f91b9>] ? irq_free_descs+0x69/0x80 [ 392.314006] [<ffffffff811084d0>] ? internal_add_timer+0xb0/0xb0 [ 392.322125] [<ffffffff81109d07>] msleep+0x37/0x50 [ 392.329037] [<ffffffffa00ec79a>] xennet_disconnect_backend.isra.24+0xda/0x390 [xen_netfront] [ 392.339658] [<ffffffffa00ecadc>] xennet_remove+0x2c/0x80 [xen_netfront] [ 392.348516] [<ffffffff81481c69>] xenbus_dev_remove+0x59/0xc0 [ 392.356257] [<ffffffff814e7217>] __device_release_driver+0x87/0x120 [ 392.364645] [<ffffffff814e7cf8>] driver_detach+0xb8/0xc0 [ 392.371989] [<ffffffff814e6e69>] bus_remove_driver+0x59/0xe0 [ 392.379883] [<ffffffff814e84f0>] driver_unregister+0x30/0x70 [ 392.387495] [<ffffffff814814b2>] xenbus_unregister_driver+0x12/0x20 [ 392.395908] [<ffffffffa00ed89b>] netif_exit+0x10/0x775 [xen_netfront] [ 392.404877] [<ffffffff81124e08>] SyS_delete_module+0x1d8/0x230 [ 392.412804] [<ffffffff8179a8ee>] system_call_fastpath+0x12/0x71 Signed-off-by: Chas Williams <3chas3@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: "Kamata, Munehisa" <kamatam@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-22rsi: Fix possible leak when loading firmwareChristian Engelmayer
commit a8b9774571d46506a0774b1ced3493b1245cf893 upstream. Commit 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory leak fix and fix the leak") also added a check on the allocation of DMA-accessible memory that may directly return. In that case the already allocated firmware data is leaked. Make sure the data is always freed correctly. Detected by Coverity CID 1316519. Fixes: 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory leak fix and fix the leak") Signed-off-by: Christian Engelmayer <cengelma@gmx.at> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-22ath10k: reject 11b tx fragmentation configurationMichal Kazior
commit 92092fe528e79c9bd25784ca0ef341d5a1d1b642 upstream. Even though there's a WMI enum for fragmentation threshold no known firmware actually implements it. Moreover it is not possible to rely frame fragmentation to mac80211 because firmware clears the "more fragments" bit in frame control making it impossible for remote devices to reassemble frames. Hence implement a dummy callback just to say fragmentation isn't supported. This effectively prevents mac80211 from doing frame fragmentation in software. This fixes Tx becoming broken after setting fragmentation threshold. Fixes: 1010ba4c5d1c ("ath10k: unregister and remove frag_threshold callback") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-22ath10k: fix dma_mapping_error() handlingMichal Kazior
commit 5e55e3cbd1042cffa6249f22c10585e63f8a29bf upstream. The function returns 1 when DMA mapping fails. The driver would return bogus values and could possibly confuse itself if DMA failed. Fixes: 767d34fc67af ("ath10k: remove DMA mapping wrappers") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03mvneta: use inband status only when explicitly enabledStas Sergeev
[ Upstream commit f8af8e6eb95093d5ce5ebcc52bd1929b0433e172 in net-next tree, will be pushed to Linus very soon. ] The commit 898b2970e2c9 ("mvneta: implement SGMII-based in-band link state signaling") implemented the link parameters auto-negotiation unconditionally. Unfortunately it appears that some HW that implements SGMII protocol, doesn't generate the inband status, so it is not possible to auto-negotiate anything with such HW. This patch enables the auto-negotiation only if explicitly requested with the 'managed' DT property. This patch fixes the following regression: https://lkml.org/lkml/2015/7/8/865 Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net> CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> CC: netdev@vger.kernel.org CC: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03net: phy: fixed_phy: handle link-down caseStas Sergeev
[ Upstream 868a4215be9a6d80548ccb74763b883dc99d32a2 in net-next tree, will be pushed to Linus very soon. ] fixed_phy_register() currently hardcodes the fixed PHY link to 1, and expects to find a "speed" parameter to provide correct information towards the fixed PHY consumer. In a subsequent change, where we allow "managed" (e.g: (RS)GMII in-band status auto-negotiation) fixed PHYs, none of these parameters can be provided since they will be auto-negotiated, hence, we just provide a zero-initialized fixed_phy_status to fixed_phy_register() which makes it fail when we call fixed_phy_update_regs() since status.speed = 0 which makes us hit the "default" label and error out. Without this change, we would also see potentially inconsistent speed/duplex parameters for fixed PHYs when the link is DOWN. CC: netdev@vger.kernel.org CC: linux-kernel@vger.kernel.org Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net> [florian: add more background to why this is correct and desirable] Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03net: dsa: bcm_sf2: Do not override speed settingsFlorian Fainelli
[ Upstream d2eac98f7d1b950b762a7eca05a9ce0ea1d878d2 in net-next tree, will be pushed to Linus very soon. ] The SF2 driver currently overrides speed settings for its port configured using a fixed PHY, this is both unnecessary and incorrect, because we keep feedback to the hardware parameters that we read from the PHY device, which in the case of a fixed PHY cannot possibly change speed. This is a required change to allow the fixed PHY code to allow registering a PHY with a link configured as DOWN by default and avoid some sort of circular dependency where we require the link_update callback to run to program the hardware, and we then utilize the fixed PHY parameters to program the hardware with the same settings. Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03macvtap: fix TUNSETSNDBUF values > 64kMichael S. Tsirkin
[ Upstream commit 3ea79249e81e5ed051f2e6480cbde896d99046e8 ] Upon TUNSETSNDBUF, macvtap reads the requested sndbuf size into a local variable u. commit 39ec7de7092b ("macvtap: fix uninitialized access on TUNSETIFF") changed its type to u16 (which is the right thing to do for all other macvtap ioctls), breaking all values > 64k. The value of TUNSETSNDBUF is actually a signed 32 bit integer, so the right thing to do is to read it into an int. Cc: David S. Miller <davem@davemloft.net> Fixes: 39ec7de7092b ("macvtap: fix uninitialized access on TUNSETIFF") Reported-by: Mark A. Peloquin Bisected-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com> Reported-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com> Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03net/mlx4_en: really allow to change RSS keyEric Dumazet
[ Upsteam commit 4671fc6d47e0a0108fe24a4d830347d6a6ef4aa7 ] When changing rss key, we do not want to overwrite user provided key by the one provided by netdev_rss_key_fill(), which is the host random key generated at boot time. Fixes: 947cbb0ac242 ("net/mlx4_en: Support for configurable RSS hash function") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eyal Perry <eyalpe@mellanox.com> CC: Amir Vadai <amirv@mellanox.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03net: dsa: bcm_sf2: Fix 64-bits register writesFlorian Fainelli
[ Upstream commit 03679a14739a0d4c14b52ba65a69ff553bfba73b ] The macro to write 64-bits quantities to the 32-bits register swapped the value and offsets arguments, we want to preserve the ordering of the arguments with respect to how writel() is implemented for instance: value first, offset/base second. Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03net: dsa: bcm_sf2: Fix ageing conditions and operationFlorian Fainelli
[ Upstream commit 39797a279d62972cd914ef580fdfacb13e508bf8 ] The comparison check between cur_hw_state and hw_state is currently invalid because cur_hw_state is right shifted by G_MISTP_SHIFT, while hw_state is not, so we end-up comparing bits 2:0 with bits 7:5, which is going to cause an additional aging to occur. Fix this by not shifting cur_hw_state while reading it, but instead, mask the value with the appropriately shitfted bitmask. The other problem with the fast-ageing process is that we did not set the EN_AGE_DYNAMIC bit to request the ageing to occur for dynamically learned MAC addresses. Finally, write back 0 to the FAST_AGE_CTRL register to avoid leaving spurious bits sets from one operation to the other. Fixes: 12f460f23423 ("net: dsa: bcm_sf2: add HW bridging support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03net: eth: altera: fix napi poll_list corruptionAtsushi Nemoto
[ Upstream commit 4548a697e4969d695047cebd6d9af5e2f6cc728e ] tse_poll() calls __napi_complete() with irq enabled. This leads napi poll_list corruption and may stop all napi drivers working. Use napi_complete() instead of __napi_complete(). Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03net: fec: clear receive interrupts before processing a packetRussell King
[ Upstream commit ed63f1dcd5788d36f942fbcce350742385e3e18c ] The patch just to re-submit the patch "db3421c114cfa6326" because the patch "4d494cdc92b3b9a0" remove the change. Clear any pending receive interrupt before we process a pending packet. This helps to avoid any spurious interrupts being raised after we have fully cleaned the receive ring, while still allowing an interrupt to be raised if we receive another packet. The position of this is critical: we must do this prior to reading the next packet status to avoid potentially dropping an interrupt when a packet is still pending. Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03usbnet: Get EVENT_NO_RUNTIME_PM bit before it is clearedEugene Shatokhin
[ Upstream commit f50791ac1aca1ac1b0370d62397b43e9f831421a ] It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in usbnet_stop(), but its value should be read before it is cleared when dev->flags is set to 0. The problem was spotted and the fix was provided by Oliver Neukum <oneukum@suse.de>. Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-03vxlan: re-ignore EADDRINUSE from igmp_joinMarcelo Ricardo Leitner
[ Upstream commit bef0057b7ba881d5ae67eec876df7a26fe672a59 ] Before 56ef9c909b40[1] it used to ignore all errors from igmp_join(). That commit enhanced that and made it error out whatever error happened with igmp_join(), but that's not good because when using multicast groups vxlan will try to join it multiple times if the socket is reused and then the 2nd and further attempts will fail with EADDRINUSE. As we don't track to which groups the socket is already subscribed, it's okay to just ignore that error. Fixes: 56ef9c909b40 ("vxlan: Move socket initialization to within rtnl scope") Reported-by: John Nielsen <lists@jnielsen.net> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29bna: fix interrupts storm caused by erroneous packetsIvan Vecera
[ Upstream commit ade4dc3e616e33c80d7e62855fe1b6f9895bc7c3 ] The commit "e29aa33 bna: Enable Multi Buffer RX" moved packets counter increment from the beginning of the NAPI processing loop after the check for erroneous packets so they are never accounted. This counter is used to inform firmware about number of processed completions (packets). As these packets are never acked the firmware fires IRQs for them again and again. Fixes: e29aa33 ("bna: Enable Multi Buffer RX") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Rasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29rocker: free netdevice during netdevice removalIdo Schimmel
[ Upstream commit 1ebd47efa4e17391dfac8caa349c6a8d35f996d1 ] When removing a port's netdevice in 'rocker_remove_ports', we should also free the allocated 'net_device' structure. Do that by calling 'free_netdev' after unregistering it. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Fixes: 4b8ac9660af ("rocker: introduce rocker switch driver") Acked-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29net/mlx4_core: Fix wrong index in propagating port change event to VFsJack Morgenstein
[ Upstream commit 1c1bf34951e8d17941bf708d1901c47e81b15d55 ] The port-change event processing in procedure mlx4_eq_int() uses "slave" as the vf_oper array index. Since the value of "slave" is the PF function index, the result is that the PF link state is used for deciding to propagate the event for all the VFs. The VF link state should be used, so the VF function index should be used here. Fixes: 948e306d7d64 ('net/mlx4: Add VF link state support') Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29virtio_net: don't require ANY_LAYOUT with VERSION_1Michael S. Tsirkin
[ Upstream commit 75993300d008f418ee2569a632185fc1d7d50674 ] ANY_LAYOUT is a compatibility feature. It's implied for VERSION_1 devices, and non-transitional devices might not offer it. Change code to behave accordingly. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29bonding: correct the MAC address for "follow" fail_over_mac policydingtianhong
[ Upstream commit a951bc1e6ba58f11df5ed5ddc41311e10f5fd20b ] The "follow" fail_over_mac policy is useful for multiport devices that either become confused or incur a performance penalty when multiple ports are programmed with the same MAC address, but the same MAC address still may happened by this steps for this policy: 1) echo +eth0 > /sys/class/net/bond0/bonding/slaves bond0 has the same mac address with eth0, it is MAC1. 2) echo +eth1 > /sys/class/net/bond0/bonding/slaves eth1 is backup, eth1 has MAC2. 3) ifconfig eth0 down eth1 became active slave, bond will swap MAC for eth0 and eth1, so eth1 has MAC1, and eth0 has MAC2. 4) ifconfig eth1 down there is no active slave, and eth1 still has MAC1, eth2 has MAC2. 5) ifconfig eth0 up the eth0 became active slave again, the bond set eth0 to MAC1. Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same MAC address, it will break this policy for ACTIVE_BACKUP mode. This patch will fix this problem by finding the old active slave and swap them MAC address before change active slave. Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29bonding: fix destruction of bond with devices different from arphrd_etherNikolay Aleksandrov
[ Upstream commit 06f6d1094aa0992432b1e2a0920b0ee86ccd83bf ] When the bonding is being unloaded and the netdevice notifier is unregistered it executes NETDEV_UNREGISTER for each device which should remove the bond's proc entry but if the device enslaved is not of ARPHRD_ETHER type and is in front of the bonding, it may execute bond_release_and_destroy() first which would release the last slave and destroy the bond device leaving the proc entry and thus we will get the following error (with dynamic debug on for bond_netdev_event to see the events order): [ 908.963051] eql: event: 9 [ 908.963052] eql: IFF_SLAVE [ 908.963054] eql: event: 2 [ 908.963056] eql: IFF_SLAVE [ 908.963058] eql: event: 6 [ 908.963059] eql: IFF_SLAVE [ 908.963110] bond0: Releasing active interface eql [ 908.976168] bond0: Destroying bond bond0 [ 908.976266] bond0 (unregistering): Released all slaves [ 908.984097] ------------[ cut here ]------------ [ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575 remove_proc_entry+0x112/0x160() [ 908.984110] remove_proc_entry: removing non-empty directory 'net/bonding', leaking at least 'bond0' [ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore usb_common [last unloaded: bonding] [ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O 4.2.0-rc2+ #8 [ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34 ffff8800358dfda8 [ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40 ffff88003e3a4280 [ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a ffffffff8172ebd0 [ 908.984181] Call Trace: [ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50 [ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0 [ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50 [ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160 [ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30 [bonding] [ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding] [ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70 [ 908.984225] [<ffffffff8142f52d>] ? unregister_pernet_operations+0x8d/0xd0 [ 908.984228] [<ffffffff8142f58d>] ? unregister_pernet_subsys+0x1d/0x30 [ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding] [ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250 [ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0 [ 908.984244] [<ffffffff8152b732>] ? entry_SYSCALL_64_fastpath+0x16/0x75 [ 908.984247] ---[ end trace 7c006ed4abbef24b ]--- Thus remove the proc entry manually if bond_release_and_destroy() is used. Because of the checks in bond_remove_proc_entry() it's not a problem for a bond device to change namespaces (the bug fixed by the Fixes commit) but since commit f9399814927ad ("bonding: Don't allow bond devices to change network namespaces.") that can't happen anyway. Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: a64d49c3dd50 ("bonding: Manage /proc/net/bonding/ entries from the netdev events") Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29net/xen-netback: off by one in BUG_ON() conditionDan Carpenter
[ Upstream commit 50c2e4dd6749725338621fff456b26d3a592259f ] The > should be >=. I also added spaces around the '-' operations so the code is a little more consistent and matches the condition better. Fixes: f53c3fe8dad7 ('xen-netback: Introduce TX grant mapping') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29net: stmmac: dwmac-rk: Fix clk rate when provided by socHeiko Stübner
commit c48fa33c1fb2ccdb4bcc863a7b841f11efe0f8b0 upstream. The first iteration of the dwmac-rk support did access an intermediate clock directly below the pll selector. This was removed in a subsequent revision, but the clock and one invocation remained. This results in the driver trying to set the rate of a non-existent clock when the soc and not some external source provides the phy clock for RMII phys. So set the rate of the correct clock and remove the remaining now completely unused definition. Fixes: 436f5ae08f9d ("GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29stmmac: troubleshoot unexpected bits in des0 & des1Alexey Brodkin
commit f1590670ce069eefeb93916391a67643e6ad1630 upstream. Current implementation of descriptor init procedure only takes care about setting/clearing ownership flag in "des0"/"des1" fields while it is perfectly possible to get unexpected bits set because of the following factors: [1] On driver probe underlying memory allocated with dma_alloc_coherent() might not be zeroed and so it will be filled with garbage. [2] During driver operation some bits could be set by SD/MMC controller (for example error flags etc). And unexpected and/or randomly set flags in "des0"/"des1" fields may lead to unpredictable behavior of GMAC DMA block. This change addresses both items above with: [1] Use of dma_zalloc_coherent() instead of simple dma_alloc_coherent() to make sure allocated memory is zeroed. That shouldn't affect performance because this allocation only happens once on driver probe. [2] Do explicit zeroing of both "des0" and "des1" fields of all buffer descriptors during initialization of DMA transfer. And while at it fixed identation of dma_free_coherent() counterpart as well. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: arc-linux-dev@synopsys.com Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Cc: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-17 22:53:04 +0000