/* * MMC definitions for OMAP2 * * Copyright (C) 2006 Nokia Corporation * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #ifndef __OMAP2_MMC_H #define __OMAP2_MMC_H #include #include #include #include #include #define OMAP15XX_NR_MMC 1 #define OMAP16XX_NR_MMC 2 #define OMAP1_MMC_SIZE 0x080 #define OMAP1_MMC1_BASE 0xfffb7800 #define OMAP1_MMC2_BASE 0xfffb7c00 /* omap16xx only */ #define OMAP24XX_NR_MMC 2 #define OMAP2420_MMC_SIZE OMAP1_MMC_SIZE #define OMAP2_MMC1_BASE 0x4809c000 #define OMAP4_MMC_REG_OFFSET 0x100 #define OMAP_MMC_MAX_SLOTS 2 /* * struct omap_mmc_dev_attr.flags possibilities * * OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can * operate with either 1.8Vdc or 3.0Vdc card voltages; this flag * should be set if this is the case. See for example Section 22.5.3 * "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia * Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R). * * OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers * don't work correctly on some MMC controller instances on some * OMAP3 SoCs; this flag should be set if this is the case. See * for example Advisory 2.1.1.128 "MMC: Multiple Block Read * Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_ * Revision F (October 2010) (SPRZ278F). */ #define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0) #define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ BIT(1) struct omap_mmc_dev_attr { u8 flags; }; struct omap_mmc_platform_data { /* back-link to device */ struct device *dev; /* number of slots per controller */ unsigned nr_slots:2; /* set if your board has components or wiring that limits the * maximum frequency on the MMC bus */ unsigned int max_freq; /* switch the bus to a new slot */ int (*switch_slot)(struct device *dev, int slot); /* initialize board-specific MMC functionality, can be NULL if * not supported */ int (*init)(struct device *dev); void (*cleanup)(struct device *dev); void (*shutdown)(struct device *dev); /* To handle board related suspend/resume functionality for MMC */ int (*suspend)(struct device *dev, int slot); int (*resume)(struct device *dev, int slot); /* Return context loss count due to PM states changing */ int (*get_context_loss_count)(struct device *dev); u64 dma_mask; /* Integrating attributes from the omap_hwmod layer */ u8 controller_flags; /* Register offset deviation */ u16 reg_offset; struct omap_mmc_slot_data { /* * 4/8 wires and any additional host capabilities * need to OR'd all capabilities (ref. linux/mmc/host.h) */ u8 wires; /* Used for the MMC driver on omap1 and 2420 */ u32 caps; /* Used for the MMC driver on 2430 and later */ u32 pm_caps; /* PM capabilities of the mmc */ /* * nomux means "standard" muxing is wrong on this board, and * that board-specific code handled it before common init logic. */ unsigned nomux:1; /* switch pin can be for card detect (default) or card cover */ unsigned cover:1; /* use the internal clock */ unsigned internal_clock:1; /* nonremovable e.g. eMMC */ unsigned nonremovable:1; /* Try to sleep or power off when possible */ unsigned power_saving:1; /* If using power_saving and the MMC power is not to go off */ unsigned no_off:1; /* eMMC does not handle power off when not in sleep state */ unsigned no_regulator_off_init:1; /* Regulator off remapped to sleep */ unsigned vcc_aux_disable_is_sleep:1; /* we can put the features above into this variable */ #define HSMMC_HAS_PBIAS (1 << 0) #define HSMMC_HAS_UPDATED_RESET (1 << 1) unsigned features; int switch_pin; /* gpio (card detect) */ int gpio_wp; /* gpio (write protect) */ int (*set_bus_mode)(struct device *dev, int slot, int bus_mode); int (*set_power)(struct device *dev, int slot, int power_on, int vdd); int (*get_ro)(struct device *dev, int slot); void (*remux)(struct device *dev, int slot, int power_on); /* Call back before enabling / disabling regulators */ void (*before_set_reg)(struct device *dev, int slot, int power_on, int vdd); /* Call back after enabling / disabling regulators */ void (*after_set_reg)(struct device *dev, int slot, int power_on, int vdd); /* if we have special card, init it using this callback */ void (*init_card)(struct mmc_card *card); /* return MMC cover switch state, can be NULL if not supported. * * possible return values: * 0 - closed * 1 - open */ int (*get_cover_state)(struct device *dev, int slot); const char *name; u32 ocr_mask; /* Card detection IRQs */ int card_detect_irq; int (*card_detect)(struct device *dev, int slot); unsigned int ban_openended:1; } slots[OMAP_MMC_MAX_SLOTS]; }; /* called from board-specific card detection service routine */ extern void omap_mmc_notify_cover_event(struct device *dev, int slot, int is_closed); #if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \ defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE) void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data, int nr_controllers); void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data); int omap_mmc_add(const char *name, int id, unsigned long base, unsigned long size, unsigned int irq, struct omap_mmc_platform_data *data); #else static inline void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data, int nr_controllers) { } static inline void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data) { } static inline int omap_mmc_add(const char *name, int id, unsigned long base, unsigned long size, unsigned int irq, struct omap_mmc_platform_data *data) { return 0; } #endif extern int omap_msdi_reset(struct omap_hwmod *oh); #endif