| Age | Commit message (Collapse) | Author |
|---|
|
commit d3b9d7a9051d7024a93c76a84b2f84b3b66ad6d5 upstream.
[This is upstream commit d3b9d7a9051d7024a93c76a84b2f84b3b66ad6d5.
It needs to be backported to kernels as old as 3.2, because it fixes the
buggy commit 9dbcaec830cd97f44a0b91b315844e0d7144746b "USB: Handle warm
reset failure on empty port."]
A USB 3.0 device can transition to the Inactive state if a U1 or U2 exit
transition fails. The current code in hub_events simply issues a warm
reset, but does not call any pre-reset or post-reset driver methods (or
unbind/rebind drivers without them). Therefore the drivers won't know
their device has just been reset.
hub_events should instead call usb_reset_device. This means
hub_port_reset now needs to figure out whether it should issue a warm
reset or a hot reset.
Remove the FIXME note about needing disconnect() for a NOTATTACHED
device. This patch fixes that.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit a24a6078754f28528bc91e7e7b3e6ae86bd936d8 upstream.
[This is upstream commit 24a6078754f28528bc91e7e7b3e6ae86bd936d8.
It needs to be backported to kernels as old as 3.2, because it fixes the
buggy commit 9dbcaec830cd97f44a0b91b315844e0d7144746b "USB: Handle warm
reset failure on empty port."]
When a hot reset fails on a USB 3.0 port, the current port reset code
recursively calls hub_port_reset inside hub_port_wait_reset. This isn't
ideal, since we should avoid recursive calls in the kernel, and it also
doesn't allow us to issue multiple warm resets on reset failures.
Rip out the recursive call. Instead, add code to hub_port_reset to
issue a warm reset if the hot reset fails, and try multiple warm resets
before giving up on the port.
In hub_port_wait_reset, remove the recursive call and re-indent. The
code is basically the same, except:
1. It bails out early if the port has transitioned to Inactive or
Compliance Mode after the reset completed.
2. It doesn't consider a connect status change to be a failed reset. If
multiple warm resets needed to be issued, the connect status may have
changed, so we need to ignore that and look at the port link state
instead. hub_port_reset will now do that.
3. It unconditionally sets udev->speed on all types of successful
resets. The old recursive code would set the port speed when the second
hub_port_reset returned.
The old code did not handle connected devices needing a warm reset well.
There were only two situations that the old code handled correctly: an
empty port needing a warm reset, and a hot reset that migrated to a warm
reset.
When an empty port needed a warm reset, hub_port_reset was called with
the warm variable set. The code in hub_port_finish_reset would skip
telling the USB core and the xHC host that the device was reset, because
otherwise that would result in a NULL pointer dereference.
When a USB 3.0 device reset migrated to a warm reset, the recursive call
made the call stack look like this:
hub_port_reset(warm = false)
hub_wait_port_reset(warm = false)
hub_port_reset(warm = true)
hub_wait_port_reset(warm = true)
hub_port_finish_reset(warm = true)
(return up the call stack to the first wait)
hub_port_finish_reset(warm = false)
The old code didn't want to notify the USB core or the xHC host of device reset
twice, so it only did it in the second call to hub_port_finish_reset,
when warm was set to false. This was necessary because
before patch two ("USB: Ignore xHCI Reset Device status."), the USB core
would pay attention to the xHC Reset Device command error status, and
the second call would always fail.
Now that we no longer have the recursive call, and warm can change from
false to true in hub_port_reset, we need to have hub_port_finish_reset
unconditionally notify the USB core and the xHC of the device reset.
In hub_port_finish_reset, unconditionally clear the connect status
change (CSC) bit for USB 3.0 hubs when the port reset is done. If we
had to issue multiple warm resets for a device, that bit may have been
set if the device went into SS.Inactive and then was successfully warm
reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 2d4fa940f99663c82ba55b2244638833b388e4e2 upstream.
[This is upstream commit 2d4fa940f99663c82ba55b2244638833b388e4e2.
It needs to be backported to kernels as old as 3.2, because it fixes the
buggy commit 9dbcaec830cd97f44a0b91b315844e0d7144746b "USB: Handle warm
reset failure on empty port."]
The next patch will refactor the hub port code to rip out the recursive
call to hub_port_reset on a failed hot reset. In preparation for that,
make sure all code paths can deal with being called with a NULL udev.
The usb_device will not be valid if warm reset was issued because a port
transitioned to the Inactive or Compliance Mode on a device connect.
This patch should have no effect on current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 0fe51aa5eee51db7c7ecd201d42a977ad79c58b6 upstream.
[This is upstream commit 0fe51aa5eee51db7c7ecd201d42a977ad79c58b6.
It needs to be backported to kernels as old as 3.2, because it fixes the
buggy commit 9dbcaec830cd97f44a0b91b315844e0d7144746b "USB: Handle warm
reset failure on empty port."]
The EHCI host controller needs to prevent EHCI initialization when the
UHCI or OHCI companion controller is in the middle of a port reset. It
uses ehci_cf_port_reset_rwsem to do this. USB 3.0 hubs can't be under
an EHCI host controller, so it makes no sense to down the semaphore for
USB 3.0 hubs. It also makes the warm port reset code more complex.
Don't down ehci_cf_port_reset_rwsem for USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 65bdac5effd15d6af619b3b7218627ef4d84ed6a upstream.
An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train. In that case, we
issue a warm reset. Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.
The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded. This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.
Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes. Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.
Make hub_events disable the port if warm reset fails. This will disable
the port, and then bring it back into the RxDetect state. Make the USB
core ignore the connect change until the device reconnects.
Note that this patch does NOT handle connected devices slipping into the
Inactive state very well. This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure. However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.
This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm
reset logic"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 0920a48719f1ceefc909387a64f97563848c7854 upstream.
This increases GEN6_RC6p_THRESHOLD from 100000 to 150000. For some
reason this avoids the gen6_gt_check_fifodbg.isra warnings and
associated GPU lockups, which makes my ivy bridge machine stable.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit bdc5c1812cea6efe1aaefb3131fcba28cd0b2b68 upstream.
While shuting down a HVM guest with pci devices passed through we
get this:
pciback 0000:04:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100002)
------------[ cut here ]------------
WARNING: at drivers/pci/pci.c:1397 pci_disable_device+0x88/0xa0()
Hardware name: MS-7640
Device pciback
disabling already-disabled device
Modules linked in:
Pid: 53, comm: xenwatch Not tainted 3.9.0-rc1-20130304a+ #1
Call Trace:
[<ffffffff8106994a>] warn_slowpath_common+0x7a/0xc0
[<ffffffff81069a31>] warn_slowpath_fmt+0x41/0x50
[<ffffffff813cf288>] pci_disable_device+0x88/0xa0
[<ffffffff814554a7>] xen_pcibk_reset_device+0x37/0xd0
[<ffffffff81454b6f>] ? pcistub_put_pci_dev+0x6f/0x120
[<ffffffff81454b8d>] pcistub_put_pci_dev+0x8d/0x120
[<ffffffff814582a9>] __xen_pcibk_release_devices+0x59/0xa0
This fixes the bug.
Reported-and-Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit e37736777254ce1abc85493a5cacbefe5983b896 upstream.
When system enters sleep, non-boot CPUs will be disabled.
Cpufreq stats sysfs is created when the CPU is up, but it is not
freed when the CPU is going down. This will cause memory leak.
Signed-off-by: xiaobing tu <xiaobing.tu@intel.com>
Signed-off-by: guifang tang <guifang.tang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 4e0855dff094b0d56d6b5b271e0ce7851cc1e063 upstream.
This patch removes redundant and unbalanced pci_disable_device() from
__e1000_shutdown(). pci_clear_master() is enough, device can go into
suspended state with elevated enable_cnt.
Bug was introduced in commit 23606cf5d1192c2b17912cb2ef6e62f9b11de133
("e1000e / PCI / PM: Add basic runtime PM support (rev. 4)") in v2.6.35
Cc: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit dcd9006b1b053c7b1cebe81333261d4fd492ffeb upstream.
hid_output_raw_report() makes a direct call to usb_control_msg(). However,
some USB3 boards have shown that the usb device is not ready during the
.probe(). This blocks the entire usb device, and the paired mice, keyboards
are not functional. The dmesg output is the following:
[ 11.912287] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
[ 11.912537] logitech-djreceiver 0003:046D:C52B.0003: logi_dj_probe:logi_dj_recv_query_paired_devices error:-32
[ 11.912636] logitech-djreceiver: probe of 0003:046D:C52B.0003 failed with error -32
Relying on the scheduled call to usbhid_submit_report() fixes the problem.
related bugs:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1072082
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1039143
https://bugzilla.redhat.com/show_bug.cgi?id=840391
https://bugzilla.kernel.org/show_bug.cgi?id=49781
Reported-and-tested-by: Bob Bowles <bobjohnbowles@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit a40e7cf8f06b4e322ba902e4e9f6a6b0c2daa907 upstream.
Commit 9f9c9cbb6057 ("drivers/firmware/dmi_scan.c: fetch dmi version
from SMBIOS if it exists") hoisted the check for "_DMI_" into
dmi_scan_machine(), which means that we don't bother to check for
"_DMI_" at offset 16 in an SMBIOS entry. smbios_present() may also call
dmi_present() for an address where we found "_SM_", if it failed further
validation.
Check for "_DMI_" in smbios_present() before calling dmi_present().
[akpm@linux-foundation.org: fix build]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: Tim McGrath <tmhikaru@gmail.com>
Tested-by: Tim Mcgrath <tmhikaru@gmail.com>
Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit e8fc41377f5037ff7a661ea06adc05f1daec1548 upstream.
vbios values are wrong leading to colors that are
too bright. Use the default values instead.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit b980955236922ae6106774511c5c05003d3ad225 upstream.
Commit 6133705494bb introduced a circular lock dependency because
posix_cpu_timers_exit() is called by release_task(), which is holding
a writer lock on tasklist_lock, and this can cause a deadlock since
kill_fasync() gets called with nonblocking_pool.lock taken.
There's no reason why kill_fasync() needs to be taken while the random
pool is locked, so move it out to fix this locking dependency.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 3e78080f81481aa8340374d5a37ae033c1cf4272 upstream.
Not having power is a pretty serious error so check that we are able to
enable the supply and error out if we can't.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit f366fccd0809f13ba20d64cae3c83f7338c88af7 upstream.
We read the chip ID from the chip, use it to determine if the chip ID provided
to the driver is correct, and report it if wrong. We should also use the
correct chip ID to select supported functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit dbd712c2272764a536e29ad6841dba74989a39d9 upstream.
Peak attributes were not initialized and cleared correctly.
Also, temp2_max is only supported on page 0 and thus does not need to be
an array.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 4a35f83b2b7c6aae3fc0d1c4554fdc99dc33ad07 upstream.
Restore crtc->fb to the old framebuffer if queue_flip fails.
While at it, kill the pointless intel_fb temp variable.
v2: Update crtc->fb before queue_flip and restore it back
after a failure.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit f7f154f1246ccc5a0a7e9ce50932627d60a0c878 upstream.
virtio_rng feeds the randomness buffer handed by the core directly
into the scatterlist, since commit bb347d98079a547e80bd4722dee1de61e4dca0e8.
However, if CONFIG_HW_RANDOM=m, the static buffer isn't a linear address
(at least on most archs). We could fix this in virtio_rng, but it's actually
far easier to just do it in the core as virtio_rng would have to allocate
a buffer every time (it doesn't know how much the core will want to read).
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 466026989f112e0546ca39ab00a759af82dbe83a upstream.
For SD8688, FUNC_INIT command is queued before fw_ready flag is
set. This causes the following crash as lbs_thread blocks any
command if fw_ready is not set.
[ 209.338953] [<c0502248>] (__schedule+0x610/0x764) from [<bf20ae24>] (__lbs_cmd+0xb8/0x130 [libertas])
[ 209.348340] [<bf20ae24>] (__lbs_cmd+0xb8/0x130 [libertas]) from [<bf222474>] (if_sdio_finish_power_on+0xec/0x1b0 [libertas_sdio])
[ 209.360136] [<bf222474>] (if_sdio_finish_power_on+0xec/0x1b0 [libertas_sdio]) from [<bf2226c4>] (if_sdio_power_on+0x18c/0x20c [libertas_sdio])
[ 209.373052] [<bf2226c4>] (if_sdio_power_on+0x18c/0x20c [libertas_sdio]) from [<bf222944>] (if_sdio_probe+0x200/0x31c [libertas_sdio])
[ 209.385316] [<bf222944>] (if_sdio_probe+0x200/0x31c [libertas_sdio]) from [<bf01d820>] (sdio_bus_probe+0x94/0xfc [mmc_core])
[ 209.396748] [<bf01d820>] (sdio_bus_probe+0x94/0xfc [mmc_core]) from [<c02e729c>] (driver_probe_device+0x12c/0x348)
[ 209.407214] [<c02e729c>] (driver_probe_device+0x12c/0x348) from [<c02e7530>] (__driver_attach+0x78/0x9c)
[ 209.416798] [<c02e7530>] (__driver_attach+0x78/0x9c) from [<c02e5658>] (bus_for_each_dev+0x50/0x88)
[ 209.425946] [<c02e5658>] (bus_for_each_dev+0x50/0x88) from [<c02e6810>] (bus_add_driver+0x108/0x268)
[ 209.435180] [<c02e6810>] (bus_add_driver+0x108/0x268) from [<c02e782c>] (driver_register+0xa4/0x134)
[ 209.444426] [<c02e782c>] (driver_register+0xa4/0x134) from [<bf22601c>] (if_sdio_init_module+0x1c/0x3c [libertas_sdio])
[ 209.455339] [<bf22601c>] (if_sdio_init_module+0x1c/0x3c [libertas_sdio]) from [<c00085b8>] (do_one_initcall+0x98/0x174)
[ 209.466236] [<c00085b8>] (do_one_initcall+0x98/0x174) from [<c0076504>] (load_module+0x1c5c/0x1f80)
[ 209.475390] [<c0076504>] (load_module+0x1c5c/0x1f80) from [<c007692c>] (sys_init_module+0x104/0x128)
[ 209.484632] [<c007692c>] (sys_init_module+0x104/0x128) from [<c0008c40>] (ret_fast_syscall+0x0/0x38)
Fix it by setting fw_ready flag prior to queuing FUNC_INIT command.
Reported-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 3e7a4ff7c5b6423ddb644df9c41b8b6d2fb79d30 upstream.
Maximum delay for waking up card is 50 ms. Because of typo in
counter, this delay goes to 500ms. This patch fixes the bug.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 3412f2f086ea7531378fabe756bd4a1109994ae6 upstream.
On many different chips, important aspects of the MAC state are not
fully cleared by a warm reset. This can show up as tx/rx hangs, those
annoying "DMA failed to stop in 10 ms..." messages or other quirks.
On AR933x, the chip can occasionally get stuck in a way that only a
driver unload/reload or a reboot would bring it back to life.
With this patch, a full reset is issued when bringing the chip out of
FULL-SLEEP state (after idle), or if either Rx or Tx was not shut down
properly. This makes the DMA related error messages disappear completely
in my tests on AR933x, and the chip does not get stuck anymore.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 838f427955dcfd16858b0108ce29029da0d56a4e upstream.
The ath9k commit 2ef167557c0a26c88162ecffb017bfcc51eb7b29
(ath9k: fix signal strength reporting issues) fixed an issue where the
reported per-frame signal strength reported to mac80211 was being
overwritten with an internal average. The same issue is also present
in ath9k_htc.
In addition to preventing the driver from overwriting the value, this
commit also ensures that the internal average (which is used for ANI)
only tracks beacons of the AP that we're connected to.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit a3d63cadbad97671d740a9698acc2c95d1ca6e79 upstream.
RSSI is being stored internally as s8 in several places. The indication
of an unset RSSI value, ATH_RSSI_DUMMY_MARKER, was supposed to have been
set to 127, but ended up being set to 0x127 because of a code cleanup
mistake. This could lead to invalid signal strength values in a few
places.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 58ebb34c49fcfcaa029e4b1c1453d92583900f9a upstream.
Create_stripe_zones returns an error slightly differently to
raid0_run and to raid0_takeover_*.
The error returned used by the second was wrong and an error would
result in mddev->private being set to NULL and sooner or later a
crash.
So never return NULL, return ERR_PTR(err), not NULL from
create_stripe_zones.
This bug has been present since 2.6.35 so the fix is suitable
for any kernel since then.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit a64685399181780998281fe07309a94b25dd24c3 upstream.
You cannot resize a RAID0 array (in terms of making the devices
bigger), but the code doesn't entirely stop you.
So:
disable setting of the available size on each device for
RAID0 and Linear devices. This must not change as doing so
can change the effective layout of data.
Make sure that the size that raid0_size() reports is accurate,
but rounding devices sizes to chunk sizes. As the device sizes
cannot change now, this isn't so important, but it is best to be
safe.
Without this change:
mdadm --grow /dev/md0 -z max
mdadm --grow /dev/md0 -Z max
then read to the end of the array
can cause a BUG in a RAID0 array.
These bugs have been present ever since it became possible
to resize any device, which is a long time. So the fix is
suitable for any -stable kerenl.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit bbfa57c0f2243a7c31fd248d22e9861a2802cad5 upstream.
If an fsync occurs on a read-only array, we need to send a
completion for the IO and may not increment the active IO count.
Otherwise, we hit a bug trace and can't stop the MD array anymore.
By advice of Christoph Hellwig we return success upon a flush
request but we return -EROFS for other writes.
We detect flush requests by checking if the bio has zero sectors.
This patch is suitable to any -stable kernel to which it applies.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: NeilBrown <neilb@suse.de>
Signed-off-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 7e5a5104c6af709a8d97d5f4711e7c917761d464 upstream.
Now zram allocates new page with GFP_KERNEL in zram I/O path
if IO is partial. Unfortunately, It may cause deadlock with
reclaim path like below.
write_page from fs
fs_lock
allocation(GFP_KERNEL)
reclaim
pageout
write_page from fs
fs_lock <-- deadlock
This patch fixes it by using GFP_NOIO. In read path, we
reorganize code flow so that kmap_atomic is called after the
GFP_NOIO allocation.
Acked-by: Jerome Marchand <jmarchand@redhat.com>
Acked-by: Nitin Gupta <ngupta@vflare.org>
[ penberg@kernel.org: don't use GFP_ATOMIC ]
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit bd97120fc3d1a11f3124c7c9ba1d91f51829eb85 upstream.
If a single descriptor crosses a region, the
second chunk length should be decremented
by size translated so far, instead it includes
the full descriptor length.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 0322bd3980b3ebf7dde8474e22614cb443d6479a upstream.
Don't let Masterkit MA901 USB radio be handled by usb hid drivers.
This device will be handled by radio-ma901.c driver.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 389cd784969e9148fedcde0608f15bd74d6b769e upstream.
This patch adds the IDE-mode SATA Device IDs for the Intel Lynx Point-LP PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 3aee8bc52c415aba8148f144e5e5359b0fd75dd1 upstream.
This patch adds the IDE-mode SATA Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit aaa515277db9585eeb4fdeb4637b9f9df50a1dd9 upstream.
This patch adds the IDE-mode SATA DeviceIDs for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit cb7da022450cdaaebd33078b6b32fb7dd2aaf6db upstream.
Since commit 8871e99f89b7 ('asus-laptop: HRWS/HWRS typo'), module
initialisation is very slow on the Asus UL30A. The HWRS method takes
about 12 seconds to run, and subsequent initialisation also seems to
be delayed. Since we don't really need the result, don't bother
calling it on init. Those who are curious can still get the result
through the 'infos' device attribute.
Update the comment about HWRS in show_infos().
Reported-by: ryan <draziw+deb@gmail.com>
References: http://bugs.debian.org/692436
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit d9904344fc4052fbe7e4dc137eba0dcdadf326bd upstream.
An earlier commit cd006086fa5d91414d8ff9ff2b78fbb593878e3c ("ata_piix:
defer disks to the Hyper-V drivers by default") broke MS Virtual PC
guests. Hyper-V guests and Virtual PC guests have nearly identical DMI
info. As a result the driver does currently ignore the emulated hardware
in Virtual PC guests and defers the handling to hv_blkvsc. Since Virtual
PC does not offer paravirtualized drivers no disks will be found in the
guest.
One difference in the DMI info is the product version. This patch adds a
match for MS Virtual PC 2007 and "unignores" the emulated hardware.
This was reported for openSuSE 12.1 in bugzilla:
https://bugzilla.novell.com/show_bug.cgi?id=737532
Here is a detailed list of DMI info from example guests:
hwinfo --bios:
virtual pc guest:
System Info: #1
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "VS2005R2"
Serial: "3178-9905-1533-4840-9282-0569-59"
UUID: undefined, but settable
Wake-up: 0x06 (Power Switch)
Board Info: #2
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "5.0"
Serial: "3178-9905-1533-4840-9282-0569-59"
Chassis Info: #3
Manufacturer: "Microsoft Corporation"
Version: "5.0"
Serial: "3178-9905-1533-4840-9282-0569-59"
Asset Tag: "7188-3705-6309-9738-9645-0364-00"
Type: 0x03 (Desktop)
Bootup State: 0x03 (Safe)
Power Supply State: 0x03 (Safe)
Thermal State: 0x01 (Other)
Security Status: 0x01 (Other)
win2k8 guest:
System Info: #1
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "7.0"
Serial: "9106-3420-9819-5495-1514-2075-48"
UUID: undefined, but settable
Wake-up: 0x06 (Power Switch)
Board Info: #2
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "7.0"
Serial: "9106-3420-9819-5495-1514-2075-48"
Chassis Info: #3
Manufacturer: "Microsoft Corporation"
Version: "7.0"
Serial: "9106-3420-9819-5495-1514-2075-48"
Asset Tag: "7076-9522-6699-1042-9501-1785-77"
Type: 0x03 (Desktop)
Bootup State: 0x03 (Safe)
Power Supply State: 0x03 (Safe)
Thermal State: 0x01 (Other)
Security Status: 0x01 (Other)
win2k12 guest:
System Info: #1
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "7.0"
Serial: "8179-1954-0187-0085-3868-2270-14"
UUID: undefined, but settable
Wake-up: 0x06 (Power Switch)
Board Info: #2
Manufacturer: "Microsoft Corporation"
Product: "Virtual Machine"
Version: "7.0"
Serial: "8179-1954-0187-0085-3868-2270-14"
Chassis Info: #3
Manufacturer: "Microsoft Corporation"
Version: "7.0"
Serial: "8179-1954-0187-0085-3868-2270-14"
Asset Tag: "8374-0485-4557-6331-0620-5845-25"
Type: 0x03 (Desktop)
Bootup State: 0x03 (Safe)
Power Supply State: 0x03 (Safe)
Thermal State: 0x01 (Other)
Security Status: 0x01 (Other)
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 23cb21092eb9dcec9d3604b68d95192b79915890 upstream.
Add module aliases so that autoloading works correctly if the user
tries to activate "snapshot-origin" or "snapshot-merge" targets.
Reference: https://bugzilla.redhat.com/889973
Reported-by: Chao Yang <chyang@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 45e27161c62216c163880d7aed751cb55a65c8e9 upstream.
Adding an include of linux/mm.h resolves this:
drivers/xen/xenbus/xenbus_client.c: In function ‘xenbus_map_ring_valloc_hvm’:
drivers/xen/xenbus/xenbus_client.c:532:66: error: implicit declaration of function ‘page_to_section’ [-Werror=implicit-function-declaration]
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 472b72f2db7831d7dbe22ffdff4adee3bd49b05d upstream.
The page++ is wrong. It makes bio_add_pc_page() pointing to a wrong page
address if the 'while (len > 0 && data_len > 0) { ... }' loop is
executed more than one once.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 3a2d63f87989e01437ba994df5f297528c353d7d upstream.
There are two problems with shutdown in the NBD driver.
1: Receiving the NBD_DISCONNECT ioctl does not sync the filesystem.
This patch adds the sync operation into __nbd_ioctl()'s
NBD_DISCONNECT handler. This is useful because BLKFLSBUF is restricted
to processes that have CAP_SYS_ADMIN, and the NBD client may not
possess it (fsync of the block device does not sync the filesystem,
either).
2: Once we clear the socket we have no guarantee that later reads will
come from the same backing storage.
The patch adds calls to kill_bdev() in __nbd_ioctl()'s socket
clearing code so the page cache is cleaned, lest reads that hit on the
page cache will return stale data from the previously-accessible disk.
Example:
# qemu-nbd -r -c/dev/nbd0 /dev/sr0
# file -s /dev/nbd0
/dev/stdin: # UDF filesystem data (version 1.5) etc.
# qemu-nbd -d /dev/nbd0
# qemu-nbd -r -c/dev/nbd0 /dev/sda
# file -s /dev/nbd0
/dev/stdin: # UDF filesystem data (version 1.5) etc.
While /dev/sda has:
# file -s /dev/sda
/dev/sda: x86 boot sector; etc.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Paul Clements <Paul.Clements@steeleye.com>
Cc: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ luis: adjust context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 3bec60d511179853138836ae6e1b61fe34d9235f upstream.
fw_device_init() didn't check whether the allocated minor number isn't
too large. Fail if it goes overflows MINORBITS.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit fd3a9025c0349bc9b01d627529f54e6e1e389015 upstream.
This patch addresses a v3.5+ regression in iscsi-target where TX thread
process context -> handle_response_queue() execution is allowed to run
unbounded while servicing constant outgoing flow of ISTATE_SEND_DATAIN
response state.
This ends up preventing memory release of StatSN acknowledged commands
in a timely manner when under heavy large block streaming DATAIN
workloads.
The regression bug was initially introduced with:
commit 6f3c0e69a9c20441bdc6d3b2d18b83b244384ec6
Author: Andy Grover <agrover@redhat.com>
Date: Tue Apr 3 15:51:09 2012 -0700
target/iscsi: Refactor target_tx_thread immediate+response queue loops
Go ahead and follow original iscsi_target_tx_thread() logic and check
to break for immediate queue processing after each DataIN Sequence and/or
Response PDU has been sent.
Reported-by: Benjamin ESTRABAUD <be@mpstor.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 3ec1c3983d73b1e3d4cfd72afab94c34eceafe8a upstream.
The call to handlers 0x124 and 0x135 (rfkill control) seems to take a
bitmask to control various states of the device. For our rfkill we need
a fully on/off. SVZ1311Z9R/X's LTE modem needs more bits up.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47751
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 208afec4f3be8c51ad6eebe6611dd6d2ad2fa298 upstream.
This bug was introduced back in bitkeeper days in 2003. We use
"dcb->dev_mode" before it has been initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 9d2696e658ef4f209955ddaa987d43f1a1bd81a1 upstream.
Properly initialize scatterlist before using it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 9d092603cc306ee6edfe917bf9ab8beb5f32d7bc upstream.
"be->mode" is obtained from xenbus_read(), which does a kmalloc() for
the message body. The short string is never released, so do it along
with freeing "be" itself, and make sure the string isn't kept when
backend_changed() doesn't complete successfully (which made it
desirable to slightly re-structure that function, so that the error
cleanup can be done in one place).
Reported-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit fbbf8555a986ed31e54f006b6cc637ea4ff1425b upstream.
This patch adds missing bounds checking for the configfs provided
mapped_lun value during target_fabric_make_mappedlun() setup ahead
of se_lun_acl initialization.
This addresses a potential OOPs when using a mapped_lun value that
exceeds the hardcoded TRANSPORT_MAX_LUNS_PER_TPG-1 value within
se_node_acl->device_list[].
Reported-by: Jan Engelhardt <jengelh@inai.de>
Cc: Jan Engelhardt <jengelh@inai.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit f528d980c17b8714aedc918ba86e058af914d66b upstream.
When dma_ops are initialized the unity mappings are
created. The init_device_table_dma() function makes sure DMA
from all devices is blocked by default. This opens a short
window in time where DMA to unity mapped regions is blocked
by the IOMMU. Make sure this does not happen by initializing
the device table after dma_ops.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 55ee64b30a38d688232e5eb2860467dddc493573 upstream.
Walking rbtree while it's modified is a Bad Idea(tm); besides,
the result of find_vma() can be freed just as it's getting returned
to caller. Fortunately, it's easy to fix - just take ->mmap_sem a bit
earlier (and don't bother with find_vma() at all if virtp >= PAGE_OFFSET -
in that case we don't even look at its result).
While we are at it, what prevents VIDIOC_PREPARE_BUF calling
v4l_prepare_buf() -> (e.g) vb2_ioctl_prepare_buf() -> vb2_prepare_buf() ->
__buf_prepare() -> __qbuf_userptr() -> vb2_vmalloc_get_userptr() -> find_vma(),
AFAICS without having taken ->mmap_sem anywhere in process? The code flow
is bloody convoluted and depends on a bunch of things done by initialization,
so I certainly might've missed something...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Archit Taneja <archit@ti.com>
Cc: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
commit 4d9b109060f690f5c835130ff54165ae157b3087 upstream.
This change fixes a deadlock when the multiplexer is closed while there
are still client side ports open.
When the multiplexer is closed and there are active tty's it tries to
close them with tty_vhangup. This has a problem though, because
tty_vhangup needs the tty_lock. This patch changes it to unlock the
tty_lock before attempting the hangup and relocks afterwards. The
additional call to tty_port_tty_set is needed because otherwise the
port stays active because of the reference counter.
This change also exposed another problem that other code paths don't
expect that the multiplexer could have been closed. This patch also adds
checks for these cases in the gsmtty_ class of function that could be
called.
The documentation explicitly states that "first close all virtual ports
before closing the physical port" but we've found this to not always
reality in our field situations. The GPRS / UTMS modem sometimes crashes
and needs a power cycle in that case which means cleanly shutting down
everything is not always possible. This change makes it much more robust
for our situation where at least the system is recoverable with this patch
and doesn't hang in a deadlock situation inside the kernel.
The patch is against the long term support kernel (3.4.27) and should
apply cleanly to more recent branches. Tested with a Telit GE864-QUADV2
and Telit HE910 modem.
Signed-off-by: Dirkjan Bussink <dirkjan.bussink@nedap.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
Commit 4c4bc25d0fa6beaf054c0b4c3b324487f266c820 upstream.
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting
meaningful output from a Lab-PC+ in differential mode for AI cmds, but
AI insn reads gave correct readings. He tracked it down to two
problems, one of which is addressed by this patch.
It seems the setting of the channel bits for particular scanning modes
was incorrect for differential mode. (Only half the number of channels
are available in differential mode; comedi refers to them as channels 0,
1, 2 and 3, but the hardware documentation refers to them as channels 0,
2, 4 and 6.) In differential mode, the setting of the channel enable
bits in the command1 register should depend on whether the scan enable
bit is set. Effectively, we need to double the comedi channel number
when the scan enable bit is not set in differential mode. The scan
enable bit gets set when the AI scan mode is `MODE_MULT_CHAN_UP` or
`MODE_MULT_CHAN_DOWN`, and gets cleared when the AI scan mode is
`MODE_SINGLE_CHAN` or `MODE_SINGLE_CHAN_INTERVAL`. The existing test
for whether the comedi channel number needs to be doubled in
differential mode is incorrect in `labpc_ai_cmd()`. This patch corrects
the test.
Thanks to Tuomas for suggesting the fix.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
|
Commit 22056e2b46246d97ff0f7c6e21a77b8daa07f02c upstream.
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting
meaningful output from a Lab-PC+ in differential mode for AI cmds, but
AI insn reads gave correct readings. He tracked it down to two
problems, one of which is addressed by this patch.
It seems that writing to the command3 register after writing to the
command4 register in `labpc_ai_cmd()` messes up the differential
reference bit setting in the command4 register. Set up the command4
register after the command3 register (as in `labpc_ai_rinsn()`) to avoid
the problem.
Thanks to Tuomas for suggesting the fix.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
|
