diff options
Diffstat (limited to 'Documentation/devicetree/bindings/arm/gic.txt')
-rw-r--r-- | Documentation/devicetree/bindings/arm/gic.txt | 61 |
1 files changed, 59 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index c7d2fa156678..45ccc2db3436 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -31,12 +31,16 @@ Main node required properties: The 3rd cell is the flags, encoded as follows: bits[3:0] trigger type and level flags. 1 = low-to-high edge triggered - 2 = high-to-low edge triggered + 2 = high-to-low edge triggered (invalid for SPIs) 4 = active high level-sensitive - 8 = active low level-sensitive + 8 = active low level-sensitive (invalid for SPIs). bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of the 8 possible cpus attached to the GIC. A bit set to '1' indicated the interrupt is wired to that CPU. Only valid for PPI interrupts. + Also note that the configurability of PPI interrupts is IMPLEMENTATION + DEFINED and as such not guaranteed to be present (most SoC available + in 2014 seem to ignore the setting of this flag and use the hardware + default value). - reg : Specifies base physical address(s) and size of the GIC registers. The first region is the GIC distributor register base and size. The 2nd region is @@ -96,3 +100,56 @@ Example: <0x2c006000 0x2000>; interrupts = <1 9 0xf04>; }; + + +* GICv2m extension for MSI/MSI-x support (Optional) + +Certain revisions of GIC-400 supports MSI/MSI-x via V2M register frame(s). +This is enabled by specifying v2m sub-node(s). + +Required properties: + +- compatible : The value here should contain "arm,gic-v2m-frame". + +- msi-controller : Identifies the node as an MSI controller. + +- reg : GICv2m MSI interface register base and size + +Optional properties: + +- arm,msi-base-spi : When the MSI_TYPER register contains an incorrect + value, this property should contain the SPI base of + the MSI frame, overriding the HW value. + +- arm,msi-num-spis : When the MSI_TYPER register contains an incorrect + value, this property should contain the number of + SPIs assigned to the frame, overriding the HW value. + +Example: + + interrupt-controller@e1101000 { + compatible = "arm,gic-400"; + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + interrupt-controller; + interrupts = <1 8 0xf04>; + ranges = <0 0 0 0xe1100000 0 0x100000>; + reg = <0x0 0xe1110000 0 0x01000>, + <0x0 0xe112f000 0 0x02000>, + <0x0 0xe1140000 0 0x10000>, + <0x0 0xe1160000 0 0x10000>; + v2m0: v2m@0x8000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0x0 0x80000 0 0x1000>; + }; + + .... + + v2mN: v2m@0x9000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0x0 0x90000 0 0x1000>; + }; + }; |