aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2010-08-29Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: firewire: ohci: work around VIA and NEC PHY packet reception bug firewire: core: do not use del_timer_sync() in interrupt context firewire: net: fix unicast reception RCODE in failure paths firewire: sbp2: fix stall with "Unsolicited response" firewire: sbp2: fix memory leak in sbp2_cancel_orbs or at send error ieee1394: Adjust confusing if indentation
2010-08-29firewire: ohci: work around VIA and NEC PHY packet reception bugStefan Richter
VIA VT6306, VIA VT6308, and NEC OrangeLink controllers do not write packet event codes for received PHY packets (or perhaps write evt_no_status, hard to tell). Work around it by overwriting the packet's ACK by ack_complete, so that upper layers that listen to PHY packet reception get to see these packets. (Also tested: TI TSB82AA2, TI TSB43AB22/A, TI XIO2213A, Agere FW643, JMicron JMB381 --- these do not exhibit this bug.) Clemens proposed a quirks flag for that, IOW whitelist known misbehaving controllers for this workaround. Though to me it seems harmless enough to enable for all controllers. The log_ar_at_event() debug log will continue to show the original status from the DMA unit. Reported-by: Clemens Ladisch <clemens@ladisch.de> (VT6308) Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-08-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: net/ipv4: Eliminate kstrdup memory leak net/caif/cfrfml.c: use asm/unaligned.h ax25: missplaced sock_put(sk) qlge: reset the chip before freeing the buffers l2tp: test for ethernet header in l2tp_eth_dev_recv() tcp: select(writefds) don't hang up when a peer close connection tcp: fix three tcp sysctls tuning tcp: Combat per-cpu skew in orphan tests. pxa168_eth: silence gcc warnings pxa168_eth: update call to phy_mii_ioctl() pxa168_eth: fix error handling in prope pxa168_eth: remove unneeded null check phylib: Fix race between returning phydev and calling adjust_link caif-driver: add HAS_DMA dependency 3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx qlcnic: fix poll implementation netxen: fix poll implementation bridge: netfilter: fix a memory leak
2010-08-28Merge branch 'drm-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6 * 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: vgaarb: Wrap vga_(get|put) in CONFIG_VGA_ARB drm/radeon/kms: add missing scratch update in dp_detect drm/modes: Fix CVT-R modeline generation drm: fix regression in drm locking since BKL removal. drm/radeon/kms: remove stray radeon_i2c_destroy drm: mm: fix range restricted allocations drm/nouveau: drop drm_global_mutex before sleeping in submission path drm: export drm_global_mutex for drivers to use drm/nv20: Don't use pushbuf calls on the original nv20. drm/nouveau: Fix TMDS on some DCB1.5 boards. drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel. drm/nv30: Apply modesetting to the correct slave encoder drm/nouveau: Use a helper function to match PCI device/subsystem IDs. drm/nv50: add dcb type 14 to enum to prevent compiler complaint
2010-08-28Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bpLinus Torvalds
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: amd64_edac: Do not report error overflow as a separate error MCE, AMD: Limit MCE decoding to current families for now
2010-08-28Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: pxa27x_keypad - remove input_free_device() in pxa27x_keypad_remove() Input: mousedev - fix regression of inverting axes Input: uinput - add devname alias to allow module on-demand load Input: hil_kbd - fix compile error USB: drop tty argument from usb_serial_handle_sysrq_char() Input: sysrq - drop tty argument form handle_sysrq() Input: sysrq - drop tty argument from sysrq ops handlers
2010-08-27drm/radeon/kms: add missing scratch update in dp_detectAlex Deucher
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-08-27drm/modes: Fix CVT-R modeline generationAdam Jackson
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16651 Signed-off-by: Adam Jackson <ajax@redhat.com> Tested-by: Adam Serbinski <adam@serbinksi.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-08-27drm: fix regression in drm locking since BKL removal.Arnd Bergmann
This locking path needs proper auditing but probably too late for changes at this point for 2.6.36, so lets go with the quick fix, which is to drop the lock around schedule. Reported-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-08-27drm/radeon/kms: remove stray radeon_i2c_destroyAlex Deucher
I missed this one in the i2c unification patch. This is handled in the core radeon i2c code now. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-08-27drm: mm: fix range restricted allocationsDaniel Vetter
With the code cleanup in 7a6b2896f261894dde287d3faefa4b432cddca53 is the first bad commit commit 7a6b2896f261894dde287d3faefa4b432cddca53 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Fri Jul 2 15:02:15 2010 +0100 drm_mm: extract check_free_mm_node I've botched up the range-restriction checks. The result is usually an X server dying with SIGBUS in libpixman (software fallback rendering). Change the code to adjust the start and end for range restricted allocations. IMHO this even makes the code a bit clearer. Fixes regression bug: https://bugs.freedesktop.org/show_bug.cgi?id=29738 Reported-by-Tested-by: Till MAtthiesen <entropy@everymail.net> Acked-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-08-27Merge remote branch 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next into ↵Dave Airlie
drm-fixes * 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next: drm/nouveau: drop drm_global_mutex before sleeping in submission path drm: export drm_global_mutex for drivers to use drm/nv20: Don't use pushbuf calls on the original nv20. drm/nouveau: Fix TMDS on some DCB1.5 boards. drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel. drm/nv30: Apply modesetting to the correct slave encoder drm/nouveau: Use a helper function to match PCI device/subsystem IDs. drm/nv50: add dcb type 14 to enum to prevent compiler complaint
2010-08-27drm/nouveau: drop drm_global_mutex before sleeping in submission pathBen Skeggs
If we keep hold of the mutex here, the process which currently holds the buffer object will never be able to release it, causing a deadlock. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-27drm: export drm_global_mutex for drivers to useBen Skeggs
Nouveau needs to be able to drop the mutex before sleeping to prevent a deadlock from occuring. Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-26qlge: reset the chip before freeing the buffersBreno Leitao
Qlge is freeing the buffers before stopping the card DMA, and this can cause some severe error, as a EEH event on PPC. This patch just stop the card and then free the resources. Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-26amd64_edac: Do not report error overflow as a separate errorBorislav Petkov
When the Overflow MCi_STATUS bit is set, EDAC reports the lost error with a "no information available" message which often puzzles users parsing the dmesg. This doesn't make much sense since this error has been lost anyway so no need for reporting it separately. Thus, report the overflow bit setting in the MCE dump instead. While at it, remove reporting of MiscV and ErrorEnable (en) which are superfluous. Now it looks like this: [ 1501.650024] MC4_STATUS: Corrected error, other errors lost: yes, CPU context corrupt: no, CECC Error [ 1501.666887] Northbridge Error, node 2 Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
2010-08-26drm/nv20: Don't use pushbuf calls on the original nv20.Francisco Jerez
The "return" command is buggy on the original nv20, it jumps back to the caller address as expected, but it doesn't clear the subroutine active bit making the subsequent pushbuf calls fail with a "stack" overflow. Signed-off-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-26drm/nouveau: Fix TMDS on some DCB1.5 boards.Francisco Jerez
The TMDS output of an nv11 was being detected as LVDS, because it uses DCB type 2 for TMDS instead of type 4. Reported-by: Bertrand VIEILLE <Vieille.Bertrand@free.fr> Signed-off-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-26drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel.Francisco Jerez
This commit fixes fdo bug 29685. Reported-by: Vlado Plaga <rechner@vlado-do.de> Signed-off-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-26drm/nv30: Apply modesetting to the correct slave encoderPatrice Mandin
Signed-off-by: Patrice Mandin <patmandin@gmail.com> Reviewed-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-26drm/nouveau: Use a helper function to match PCI device/subsystem IDs.Francisco Jerez
Signed-off-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-26drm/nv50: add dcb type 14 to enum to prevent compiler complaintBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2010-08-25libata-sff: remove harmful BUG_ON from ata_bmdma_qc_issueMark Lord
Remove harmful BUG_ON() from ata_bmdma_qc_issue(), as it casts too wide of a net and breaks sata_mv. It also crashes the kernel while doing the BUG_ON(). There's already a WARN_ON_ONCE() further down to catch the case of POLLING for a BMDMA operation. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Cc: stable@kernel.org
2010-08-25sata_mv: fix broken DSM/TRIM support (v2)Mark Lord
Fix DSM/TRIM commands in sata_mv (v2). These need to be issued using old-school "BM DMA", rather than via the EDMA host queue. Since the chips don't have proper BM DMA status, we need to be more careful with setting the ATA_DMA_INTR bit, since DSM/TRIM often has a long delay between "DMA complete" and "command complete". GEN_I chips don't have BM DMA, so no TRIM for them. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Cc: stable@kernel.org
2010-08-25libata: be less of a drama queen on empty data commandsTejun Heo
ata_qc_issue() BUG_ON()s on data commands w/o data, which may be submitted via SG_IO. Be less of a drama queen and just trigger WARN_ON_ONCE() and fail the command with AC_ERR_SYSTEM. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Stefan Hübner <stefan.huebner@stud.tu-ilmenau.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-08-25[libata] sata_dwc_460ex: signdness bugDan Carpenter
dma_dwc_xfer_setup() returns an int and "dma_chan" needs to be signed for the error handling to work. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-08-25ahci: add HFLAG_YES_FBS and apply it to 88SE9128Tejun Heo
88SE9128 can do FBS and sets it in HOST_CAP but forgets to set FBSCP in PORT_CMD. Implement AHCI_HFLAG_YES_FBS and apply it to 88SE9128. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-08-25libata: remove no longer needed pata_winbond driverBartlomiej Zolnierkiewicz
Winbond W83759A controller is fully supported by pata_legacy driver so remove no longer needed pata_winbond driver. Leave PATA_WINBOND_VLB config option for compatibility reasons and teach pata_legacy to preserve the old behavior of pata_winbond driver. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-08-25pata_cmd64x: revert commit d62f5576Tejun Heo
Commit d62f5576 (pata_cmd64x: fix handling of address setup timings) incorrectly called ata_timing_compute() on UDMA mode on 0 @UT leading to devide by zero fault. Revert it until better fix is available. This is reported in bko#16607 by Milan Kocian who also root caused it. https://bugzilla.kernel.org/show_bug.cgi?id=16607 Signed-off-by: Tejun Heo <tj@kernel.org> Reported-and-root-caused-by: Milan Kocian <milan.kocian@wq.cz> Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-08-25Merge branch 'hwmon-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging * 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: MAINTAINERS: hwmon/coretemp: Change maintainers hwmon: (k8temp) Differentiate between AM2 and ASB1 hwmon: (ads7871) Fix ads7871_probe error paths hwmon: (coretemp) Fix harmless build warning
2010-08-25Merge branch 'upstream/core' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen * 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen: xen: handle events as edge-triggered xen: use percpu interrupts for IPIs and VIRQs
2010-08-25Input: pxa27x_keypad - remove input_free_device() in pxa27x_keypad_remove()Axel Lin
No need to call input_free_device() after input_unregister_device(). Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2010-08-25Input: mousedev - fix regression of inverting axesChristoph Fritz
Introduced by 987a6c0298260b7aa40702b349282554d6180e4b a swap in max/min calculation gets fixed by this patch. Reported-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2010-08-25hwmon: (k8temp) Differentiate between AM2 and ASB1Andreas Herrmann
Commit 8bf0223ed515be24de0c671eedaff49e78bebc9c (hwmon, k8temp: Fix temperature reporting for ASB1 processor revisions) fixed temperature reporting for ASB1 CPUs. But those CPU models (model 0x6b, 0x6f, 0x7f) were packaged both as AM2 (desktop) and ASB1 (mobile). Thus the commit leads to wrong temperature reporting for AM2 CPU parts. The solution is to determine the package type for models 0x6b, 0x6f, 0x7f. This is done using BrandId from CPUID Fn8000_0001_EBX[15:0]. See "Constructing the processor Name String" in "Revision Guide for AMD NPT Family 0Fh Processors" (Rev. 3.46). Cc: Rudolf Marek <r.marek@assembler.cz> Cc: stable@kernel.org [.32.x, .33.x, .34.x, .35.x] Reported-by: Vladislav Guberinic <neosisani@gmail.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-08-25hwmon: (ads7871) Fix ads7871_probe error pathsAxel Lin
1. remove 'status' variable 2. remove unneeded initialization of 'err' variable 3. return missing error code if sysfs_create_group fail. 4. fix the init sequence as: - check hardware existence - kzalloc for ads7871_data - sysfs_create_group - hwmon_device_register Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: stable@kernel.org Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-08-25hwmon: (coretemp) Fix harmless build warningJean Delvare
Fix the following build warning: CC [M] drivers/hwmon/coretemp.o drivers/hwmon/coretemp.c: In function "coretemp_init": drivers/hwmon/coretemp.c:521: warning: unused variable "n" drivers/hwmon/coretemp.c:521: warning: unused variable "p" Introduced by commit 851b29cb3b196cb66452ec964ab5f66c9c9cd1ed. When you drop code, you also have to drop the variables this code was using. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Chen Gong <gong.chen@linux.intel.com> Cc: Rudolf Marek <r.marek@assembler.cz> Cc: Huaxu Wan <huaxu.wan@intel.com>
2010-08-24pxa168_eth: silence gcc warningsDan Carpenter
Casting "pep->tx_desc_dma" to to a struct tx_desc pointer makes gcc complain: drivers/net/pxa168_eth.c:657: warning: cast to pointer from integer of different size Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24pxa168_eth: update call to phy_mii_ioctl()Dan Carpenter
The phy_mii_ioctl() function changed recently. It now takes a struct ifreq pointer directly. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24pxa168_eth: fix error handling in propeDan Carpenter
A couple issues here: * Some resources weren't released. * If alloc_etherdev() failed it would have caused a NULL dereference because "pep" would be null when we checked "if (pep->clk)". * Also it's better to propagate the error codes from mdiobus_register() instead of just returning -ENOMEM. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24pxa168_eth: remove unneeded null checkDan Carpenter
"pep->pd" isn't checked consistently in this function. For example it's dereferenced unconditionally on the next line after the end of the if condition. This function is only called from pxa168_eth_probe() and pep->pd is always non-NULL so I removed the check. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24phylib: Fix race between returning phydev and calling adjust_linkAnton Vorontsov
It is possible that phylib will call adjust_link before returning from {,of_}phy_connect(), which may cause the following [very rare, though] oops upon reopening the device: Unable to handle kernel paging request for data at address 0x0000024c Oops: Kernel access of bad area, sig: 11 [#1] PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0 P1021 RDB Modules linked in: NIP: c0345dac LR: c0345dac CTR: c0345d84 TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0 [...] NIP [c0345dac] adjust_link+0x28/0x19c LR [c0345dac] adjust_link+0x28/0x19c Call Trace: [c0d25f00] [000045e1] 0x45e1 (unreliable) [c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554 [...] Here is why. Drivers store phydev in their private structures, e.g. gianfar driver: static int init_phy(struct net_device *dev) { ... priv->phydev = of_phy_connect(...); ... } So that adjust_link could retrieve it back: static void adjust_link(struct net_device *dev) { ... struct phy_device *phydev = priv->phydev; ... } If the device has been opened before, then phydev->state is set to PHY_HALTED (or undefined if the driver didn't call phy_stop()). Now, phy_connect starts the PHY state machine before returning phydev to the driver: phy_start_machine(phydev, NULL); if (phydev->irq > 0) phy_start_interrupts(phydev); return phydev; The time between 'phy_start_machine()' and 'return phydev' is undefined. The start machine routine delays execution for 1 second, which is enough for most cases. But under heavy load, or if you're unlucky, it is quite possible that PHY state machine will execute before phy_connect() returns, and so adjust_link callback will try to dereference phydev, which is not yet ready. To fix the issue, simply initialize the PHY's state to PHY_READY during phy_attach(). This will ensure that phylib won't call adjust_link before phy_start(). Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24caif-driver: add HAS_DMA dependencyHeiko Carstens
Fix this error on an s390 allyesconfig build: linux-2.6/drivers/net/caif/caif_spi.c:98: undefined reference to `dma_free_coherent' Cc: Sjur Braendeland <sjur.brandeland@stericsson.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-24drm/i915: fix vblank wait test conditionJesse Barnes
When converting this to the new wait_for macro I inverted the wait condition, which causes all sorts of problems. So correct it to fix several failures caused by the bad wait (flickering, bad output detection, tearing, etc.). Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-24xen: handle events as edge-triggeredJeremy Fitzhardinge
Xen events are logically edge triggered, as Xen only calls the event upcall when an event is newly set, but not continuously as it remains set. As a result, use handle_edge_irq rather than handle_level_irq. This has the important side-effect of fixing a long-standing bug of events getting lost if: - an event's interrupt handler is running - the event is migrated to a different vcpu - the event is re-triggered The most noticable symptom of these lost events is occasional lockups of blkfront. Many thanks to Tom Kopec and Daniel Stodden in tracking this down. Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Tom Kopec <tek@acm.org> Cc: Daniel Stodden <daniel.stodden@citrix.com> Cc: Stable Kernel <stable@kernel.org>
2010-08-24xen: use percpu interrupts for IPIs and VIRQsJeremy Fitzhardinge
IPIs and VIRQs are inherently per-cpu event types, so treat them as such: - use a specific percpu irq_chip implementation, and - handle them with handle_percpu_irq This makes the path for delivering these interrupts more efficient (no masking/unmasking, no locks), and it avoid problems with attempts to migrate them. Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Stable Kernel <stable@kernel.org>
2010-08-24intel_scu_ipc: fix IPC i2c write bugJianwei Yang
We should pass the data to the data register. Signed-off-by: Jianwei Yang <jianwei.yang@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-24rar: Fix off by one errorOssama Othman
It looks like there is an off-by-one error in one of your changes to drivers/staging/rar_register/rar_register.c: Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-24V4L/DVB: mantis: Fix IR_CORE dependencyIngo Molnar
This build bug triggers: drivers/built-in.o: In function `mantis_exit': (.text+0x377413): undefined reference to `ir_input_unregister' drivers/built-in.o: In function `mantis_input_init': (.text+0x3774ff): undefined reference to `__ir_input_register' If MANTIS_CORE is enabled but IR_CORE is not. Add the correct dependency. Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-24MCE, AMD: Limit MCE decoding to current families for nowBorislav Petkov
Limit MCE error decoding to current and older families only (K8-F11h). Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
2010-08-243c59x: Fix deadlock between boomerang_interrupt and boomerang_start_txNeil Horman
If netconsole is in use, there is a possibility for deadlock in 3c59x between boomerang_interrupt and boomerang_start_xmit. Both routines take the vp->lock, and if netconsole is in use, a pr_* call from the boomerang_interrupt routine will result in the netconsole code attempting to trnasmit an skb, which can try to take the same spin lock, resulting in deadlock. The fix is pretty straightforward. This patch allocats a bit in the 3c59x private structure to indicate that its handling an interrupt. If we get into the transmit routine and that bit is set, we can be sure that we have recursed and will deadlock if we continue, so instead we just return NETDEV_TX_BUSY, so the stack requeues the skb to try again later. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>